Teac-AI301DA-dac-sm维修电路原理图.pdf

《Teac-AI301DA-dac-sm维修电路原理图.pdf》由会员分享，可在线阅读，更多相关《Teac-AI301DA-dac-sm维修电路原理图.pdf（75页珍藏版）》请在收音机爱好者资料库上搜索。

1、D-0028 AI-301DA USB DAC STEREO INTEGRATED AMPLIFIER SERVICE MANUAL Effective: April 2014 INSTRUCTIONS FOR SERVICE PERSONNEL BEFORE RETURNING APPLIANCE TO THE CUSTOMER, MAKE LEAKAGE-CURRENT OR RESISTANCE MEASUREMENTS TO DETERMINE THAT EXPOSED PARTS ARE ACCEPTABLY INSULATED FROM THE SUPPLY CIRCUIT. 目次

2、 1. 仕様.2 2. 寸法図.3 3. 動作確認.4 4. POWER.AMP 交換. .8 5. USB.8 6. .9 7. 結線図.10 8. 分解図.11 9. 基板図.13 10.安全部品.19 11.付属品.20 Contents 1.Specifications.2 2.Dimensional.drawings.3 3.Checking.operation.4 4.Power.Amp.Assembly.and.change.guide. .8 5.Updating.the.USB.Driver.8 6.Block.Diagram.9 7.Wiring.Diagram.10 8.

3、Exploded.Views.and.Parts.List.11 9.PC.Boards.and.Parts.List.13 10.Safety.parts.19 11.Included.Accessories.20 Z RadioFans.CN 收音机爱 好者资料库 - 2 - TEAC AI-301DA 1. Specifications 仕様 Amplifier Section Maximum power output : 20 W + 20 W (JEITA 10%, 1 kHz, 8 ) 40 W + 40 W (JEITA 10%, 1 kHz, 4 ) Rated power o

4、utput : 15 W + 15 W (JEITA 1%, 1 kHz, 8 ) 28 W + 28 W (JEITA 1%, 1 kHz, 4 ) Total Harmonic Distortion : 0.01% (1 kHz, 8 , 1W) Signal-to-noise ratio LINE IN : 95 dB (IHF-A/LPF 20kHz 1kHz 2V input) Frequency Response : 2 Hz 100 kHz (5 dB) Digital audio input Coaxial digital jack (75) 1 : 0.5 Vp-p Opti

5、cal digital connector 1 : 24.0 to 14.5 dBm peak USB port (type B) connector : USB 2.0 Supported sampling frequencies (PCM) : 32/44.1/48/88.2/96/176.4/192 kHz ( 96kHz maximum when using optical digital input) Supported bit lengths : 16/24 bits Supported sampling frequencies (DSD) : 2.8/5.6 MHz (only

6、when connected by USB) Bluetooth Bluetooth version : V2.1+EDR Output : Class 2 Supported profiles : A2DP, AVRCP Headphones output Rated output : 100 mW+100 mW (32 , 1 kHz) Total harmonic distortion : 0.005% General Power supply Model for Europe : AC 230 V, 50 Hz Model for USA/Canada : AC 120 V, 60 H

7、z Power consumption : 38 W Dimension (W H D) : 215 61 254 mm (8 3/8” 2 3/8” 10”) (including protrusions) Weight : 2.1 kg (4 5/8 lb) Operating temperature : +5C to +35C Operating humidity : 5% to 85% (no condensation) Storage temperature : 20C to +55C 部 最大出力:20W20W(JEITA10%1kHz8) 40W40W(JEITA10%1kHz4

8、) 定格出力:15W15W(JEITA1%1kHz8) 28W28W(JEITA1%1kHz4) 全高調波歪率:0.01%(1KHz、8、1W) S/N比 LINEIN:95dB(IHF-A/LPF20kHz1kHz2V入力) 周波数特性:2Hz 100kHz(5dB) 音声入力 同軸端子(75)1:0.5Vp-p 光端子1:24.0 14.5dBmpeak USB-B端子:USB2.0準拠 対応周波数(PCM) :32/44.1/48/88.2/96/176.4/192kHz (光 入 力 時 最 大96kHz) 対応数:16/24 対応周波数(DSD) :2.8/5.6MHz (USB接続

9、時対応) Bluetooth Bluetooth:V2.1+EDR 出力:Class2 対応:A2DP、AVRCP 出力 定格出力:100mW100mW(32、 kHz) 全高調波歪率:0.005% 一般 電源:AC100V50-60Hz 消費電力:38W 外形寸法:215mmx61mmx254mm (WxHxD、突起部含) 質量:2.1kg 許容動作温度:535 許容動作湿度:5 85 (結露) 許容保管温度:2055 RadioFans.CN 收音机爱 好者资料库 - 3 - TEAC AI-301DA 2. Dimensional drawings 寸法図 ? ? ? ? - 4 - T

10、EAC AI-301DA 3. Checking operation 動作確認 1. Preparation i Computer with Windows Vista, Windows 7 or Windows 8 in- stalled i TEAC HR Audio Player audio playback software This can be downloaded from the TEAC website (http:/teac. jp/). (Install TEAC HR Audio Player on the above computer.) i DSD files DS

11、D files : 2.8/5.6 MHz These can be downloaded from the service website (https:/ service1.teac.co.jp/). (Prepare a dedicated folder on the above computer.) i Dedicated USB driver This can be downloaded from the TEAC website (http:/teac. jp/). (Install the USB driver on the above computer.) i CD playe

12、r (Use a CD player with digital output capability such as the CD- 500, CD-6010 and CD-200 series.) i Bluetooth device i Prepare speakers (48 impedance). Connect the / terminals on the speakers with the / speaker terminals on the back of this unit. i Prepare a subwoofer speaker. Connect it to the sub

13、woofer terminal on the back of this unit. i Turn the VOLUME control on the front of the unit left until the “i” mark is at the “MIN” (minimum) position. i Headphones with a 6.3mm stereo plug i Turn this units AUTO POWER SAVE (APS) function off. Turning the APS function off When the unit is on, press

14、 and hold the standby/on () button for about 5 seconds until all the input indicators become lit or unlit. This indicator state shows whether the APS function is on or off. All input indicators unlit: APS function on All input indicators lit: APS function off About 2 seconds after the unit is put in

15、to standby or turned on, the APS function setting will be shown for about 4 seconds by the indicators. CAUTION i If the unit is turned on when the volume “i” mark is at any po- sition other than “MIN” (minimum), a sudden loud noise might occur. This could damage the speakers, harm your hearing or ca

16、use other trouble. i If the APS function is kept on when the unit is switched to test- ing mode, the unit will turn off during the operations. 1. 準備 i WindowsXP、WindowsVista、Windows7、Windows8 OS搭載PC i 音楽再生TEACHRAudioPlayer TEAC(http:/teac.jp/)入手可能。 (上記PC、TEACHRAudioPlayer 用意) i DSD DSD:2.8/5.6MHz 用(

17、https:/service1.teac.co.jp/) 入手可能。 (上記PC、専用用意準備) i 専用USB TEAC(http:/teac.jp/)入手可能。 (上記PC、専用USB 用意) i CD (CD-500、CD-6010、CD-200出 力可能CD ) i Bluetooth機器 i (:48)用意。 /本機背面 /端子 接続。 i 用意。 本機背面端子接続。 i 本機前面VOLUME左回、i MIN位置(最小)。 i 6.3mm付 i 本機AUTOPOWERSAVE機能(以下、APS)。 APS機能場合 電源状態/()約5 秒間長押、全入力点灯 又消灯。状態APS機能 /選

18、択。 入力全消灯：APS機能 入力全点灯：APS機能 上記APS機能、本機/時2秒後 APS状態約4秒間、表示。 注意 i iMIN位置(最小)以外、本機 電源突然大音出、 破損、聴力障害原因。 i APS機能、移行 操作途中電源。 - 5 - TEAC AI-301DA 2. Checking USB input 1) Use a USB cable to connect the USB port on the back of this unit to the computer. 2) First, start the computer, and launch TEAC HR Audio P

19、layer. 3) Press the units standby/on () button to turn it on. Press the SOURCE button on the front of the unit repeatedly until the USB input indicator LED lights. 4) Use TEAC HR Audio Player to open (Fig-1-1) the DSD (Fig-1- 2) file saved on the computer. 5) Select the file shown in TEAC HR Audio P

20、layer and press the PLAY button (Fig-1-3). 6) Gradually turn the VOLUME knob on the front of the unit clockwise and confirm that sound is coming from the speakers, including the subwoofer. After confirming this, return the VOLUME to its “MIN” (mini- mum) position. 7) Quit TEAC HR Audio Player on the

21、 computer and end the USB connection between this unit and the computer. Confirm that the USB input indicator blinks when you do this. 3. Checking Bluetooth input 1) Press the SOURCE button on the front of the unit repeatedly until the Bluetooth input indicator LED lights. 2) Use the other Bluetooth

22、 device to pair or connect with this unit. To ready this unit for pairing, after putting it into Bluetooth mode, press and hold the SOURCE button for at least 3 sec- onds. When the unit is ready for pairing, its Bluetooth input indicator will begin flashing rapidly. If the other Bluetooth de- vice r

23、equires the input of a passcode on its setting screen, input “0000” (four zeros). 3) When the unit confirms connection with the other Bluetooth device, its Bluetooth input indicator will stop flashing, but stay lit. Start playback of an audio file on the other Bluetooth device, gradually turn the VO

24、LUME knob on the front of the unit clockwise and confirm that sound is coming from the speakers, including the subwoofer. After confirming this, return the VOL- UME to its “MIN” (minimum) position. 4) End the connection with the other Bluetooth device, and con- firm that the Bluetooth input indicato

25、r starts blinking. 2. USB入力確認 1)本機背面USB端子PCUSB接続。 2)最初PC起動、TEACHRAudioPlayer立上 。 3)本機/()。 正面SOURCE繰返押、 入力 USBLED点灯。 4)TEACHRAudioPlayer、PC保存(Fig-1-1) DSD(Fig-1-2)開。 5)TEACHRAudioPlayer表示選択、 PLAY(再生)(Fig-1-3)押。 6)前面VOLUME徐右側回、 音 確認。 確認後、VOLUME位置MIN位置(最小) 戻。 7)PCTEACHRAudioPlayer閉、本機PCUSB接 続解除、入力 USB点

26、滅 確認。 3. Bluetooth入力確認 1)正面SOURCE繰返押、 入力 BluetoothLED点灯。 2)Bluetooth機器本機接続行。 本機待機状態、本機Bluetooth SOURCE3秒以上長押 。待機状態、入力 Bluetooth速点滅切替。 、Bluetooth機器設定画面入力要 求場合、0000(4)入力。 3)Bluetooth機器接続確認、入力 Bluetooth点灯切替。 Bluetooth機器音楽再生、前面 VOLUME徐右側回、 音確認。 確認後、VOLUME位置MIN位置(最小) 戻。 4)Bluetooth機器接続解除、入力 Bluetooth点滅確認

27、。 2 ? 1 3 - 6 - TEAC AI-301DA 4. Checking the COAXIAL input 1) Connect the coaxial digital output from the CD player to the COAXIAL input connector on the back of this unit. 2) Press the SOURCE button on the front of the unit repeatedly until the COAXIAL input indicator LED lights. 3) Start CD playe

28、r playback, gradually turn the VOLUME knob on the front of the unit clockwise and confirm that sound is com- ing from the speakers, including the subwoofer. After confirming this, return the VOLUME to its “MIN” (mini- mum) position. 4) Confirm that the COAXIAL input indicator blinks when the CD play

29、er is turned off. 5. Checking the OPTICAL input 1) Connect the optical digital output from the CD player to the OPTICAL input connector on the back of this unit. 2) Press the SOURCE button on the front of the unit repeatedly until the OPTICAL input indicator LED lights. 3) Start CD player playback,

30、gradually turn the VOLUME knob on the front of the unit clockwise and confirm that sound is com- ing from the speakers, including the subwoofer. After confirming this, return the VOLUME to its “MIN” (mini- mum) position. 4) Confirm that the OPTICAL input indicator blinks when the CD player is turned

31、 off. 6. Checking the LINE 1 input 1) Connect the L/R analog audio outputs of the CD player to the L/R LINE 1 input jacks on the back of this unit. 2) Press the SOURCE button on the front of the unit repeatedly until the LINE 1 input indicator LED lights. 3) Start CD player playback, gradually turn

32、the VOLUME knob on the front of the unit clockwise and confirm that sound is com- ing from the speakers, including the subwoofer. After confirming this, return the VOLUME to its “MIN” (mini- mum) position. 7. Checking the headphones output 1) Connect the L/R analog audio outputs of the CD player to

33、the L/R LINE 1 input jacks on the back of this unit. Connect the prepared headphones with a 6.3mm stereo plug to the headphones jack on the front of the unit. 2) Press the SOURCE button on the front of the unit repeatedly until the LINE 1 input indicator LED lights. 3) Start CD player playback, grad

34、ually turn the VOLUME knob on the front of the unit clockwise and confirm that sound is com- ing from the headphones. After confirming this, return the VOLUME to its “MIN” (mini- mum) position. 8. Checking the LINE 2 input 1) Connect the L/R audio outputs of the CD player to the L/R LINE 2 input jac

35、ks on the back of this unit. 2) Press the SOURCE button on the front of the unit repeatedly until the LINE 2 input indicator LED lights. 3) Start CD player playback, gradually turn the VOLUME knob on the front of the unit clockwise and confirm that sound is com- ing from the speakers, including the

36、subwoofer. After confirming this, return the VOLUME to its “MIN” (mini- mum) position . 4. COAXIAL入力確認 1)CD出力COAXIAL本機背面 COAXIAL入力端子接続。 2)正面SOURCE繰返押、 入力 COAXIALLED点灯。 3)CD再生、前面VOLUME 徐右側回、 音確認。 確認後、VOLUME位置MIN位置(最小) 戻。 4)CD電源際、入力 COAXIAL点滅確認。 5. OPTICAL入力確認 1)CD出力OPTICAL本機背面 OPTICAL入力端子接続。 2)正面SOUR

37、CE繰返押、 入力 OPTICALLED点灯。 3)CD再生、前面VOLUME 徐右側回、 音確認。 確認後、VOLUME位置MIN位置(最小) 戻。 4)CD電源際、入力 OPTICAL点滅確認。 6. LINE1入力確認 1)CD音声出力L/R本機背面 LINE1入力L/R端子接続。 2)正面SOURCE繰返押、 入力 LINE1LED点灯。 3)CD再生、前面VOLUME 徐右側回、 音確認。 確認後、VOLUME位置MIN位置(最小) 戻。 7. 出力確認 1)CD音声出力L/R本機背面 LINE1入力L/R端子接続。 用意6.3mm付前面 端子接続。 2)正面SOURCE繰返押、 入

38、力 LINE1LED点灯。 3)CD再生、前面VOLUME 徐右側回、音 確認。 確認後、VOLUME位置MIN位置(最小) 戻。 8. LINE2入力確認 1)CD音声出力L/R本機背面LINE2入力 L/R端子接続。 2)正面SOURCE繰返押、 入力 LINE2LED点灯。 3)CD再生、前面VOLUME 徐右側回、 音確認。 確認後、VOLUME位置MIN位置(最小) 戻。 - 7 - TEAC AI-301DA 9. Checking the firmware versions (main unit and USB) 1) Confirm the latest firmware ve

39、rsion on the service manual homepage (https:/service1.teac.co.jp/). 2) If the unit is in standby/on, press the standby/on () button to turn it off. After turning the unit off, wait at least 3 seconds before operat- ing the unit again. 3) Press and hold both the SOURCE and standby/on () buttons on th

40、e front of the unit for 5 seconds. 4) After 5 seconds, when you release both buttons, the input in- dicators will show the main unit firmware version being used. You can temporarily switch to showing the USB firmware ver- sion by pressing and holding the SOURCE button. i Switching the firmware displ

41、ay SOURCE button Not pressedMain unit firmware version PressedUSB firmware version i Firmware version indication IInput indicator LINE 2 lit: Version 1 LINE 1 lit: Version 2 LINE 1+LINE 2 lit: Version 3 OPTICAL lit: Version 4 OPTICAL+LINE 2 lit: Version 5 5) After using the above table to confirm th

42、at the latest firmware versions are being used, press the standby/on () button to turn the unit off. 9. FirmwareVersion(本体USB)確認 1)最新各 (https:/service1.teac.co.jp/)確認。 2)本機/状態場合、/ ()押、。 /確認、3秒経過本機 操作行。 3)本機正面SOURCE/ ()5秒間、押。 4)5秒間経過後、各手離状態入力 本体表示。 、SOURCE押間、USB 表示切替。 i 切替 SOURCE 本体 USB i 表示 入力 LINE2

43、点灯: Version1 LINE1点灯: Version2 LINE1+LINE2点灯: Version3 OPTICAL点灯: Version4 OPTICAL+LINE2点灯: Version5 5)上記表各最新 確認後、/()押、 本機。 - 8 - TEAC AI-301DA 4. Power Amp Assembly and change guide POWER.AMP 交換 Checking the destination voltage of the POWER AMP unit When changing the POWER AMP unit, pay attention t

44、o the jumper pin insertion position of the included part, which is set according to the destination voltage. Part number P200 i AC115V JPN, T/C: short between pins 1 and 2 i AC230V EUR, UK: short between pins 2 and 3 Confirming the DC offset voltage of the speaker terminals Connect a tester between the / speaker terminals of the L (or R) channel, and confirm that when there is no signal the DC voltage is within the range below for that channel. DC voltage = 0 V within 30 mV POWERAMP仕向電圧確認 POWERAMP交換際、仕