Pioneer-VSX1130K-avr-sm维修电路原理图.pdf

《Pioneer-VSX1130K-avr-sm维修电路原理图.pdf》由会员分享，可在线阅读，更多相关《Pioneer-VSX1130K-avr-sm维修电路原理图.pdf（59页珍藏版）》请在收音机爱好者资料库上搜索。

1、ORDER NO. PIONEER CORPORATION 1-1, Shin-ogura, Saiwai-ku, Kawasaki-shi, Kanagawa 212-0031, Japan PIONEER ELECTRONICS (USA) INC. P.O. Box 1760, Long Beach, CA 90801-1760, U.S.A. PIONEER EUROPE NV Haven 1087, Keetberglaan 1, 9120 Melsele, Belgium PIONEER ELECTRONICS ASIACENTRE PTE. LTD. 253 Alexandra

2、Road, #04-01, Singapore 159936 PIONEER CORPORATION2015 2015 Printed in Japan VSX-1130-K RRV4596 AV Receiver VSX-1130-K VSX-90 THIS MANUAL IS APPLICABLE TO THE FOLLOWING MODEL(S) AND TYPE(S). THIS SERVICE MANUAL SHOULD BE USED TOGETHER WITH THE FOLLOWING MANUAL(S). ModelTypePower RequirementRemarks V

3、SX-1130-KCUXESMAC 120 V VSX-90CUXEAC 120 V ModelOrder No.Remarks VSX-1130-K, VSX-90RRV4597SCHEMATIC DIAGRAM, PCB CONNECTION DIAGRAM, PCB PARTS LIST K-MZV MAR. RadioFans.CN 收音机爱 好者资料库 2VSX-1130-K 1234 A B C D E F 1234 SAFETY INFORMATION WARNING This product may contain a chemical known to the State o

4、f California to cause cancer, or birth defects or other reproductive harm. Health it is not meant for the casual do-it- yourselfer. Qualified technicians have the necessary test equipment and tools, and have been trained to properly and safely repair complex products such as those covered by this ma

5、nual. Improperly performed repairs can adversely affect the safety and reliability of the product and may void the warranty. If you are not qualified to perform the repair of this product properly and safely, you should not risk trying to do so and refer the repair to a qualified service technician.

6、 1. SAFETY PRECAUTIONS The following check should be performed for the continued protection of the customer and service technician. LEAKAGE CURRENT CHECK Measure leakage current to a known earth ground (water pipe, conduit, etc.) by connecting a leakage current tester such as Simpson Model 229-2 or

7、equivalent between the earth ground and all exposed metal parts of the appliance (input/output terminals, screwheads, metal overlays, control shaft, etc.). Plug the AC line cord of the appliance directly into a 120 V AC 60 Hz outlet and turn the AC power switch on. Any current measured must not exce

8、ed 0.5 mA. ANY MEASUREMENTS NOT WITHIN THE LIMITS OUTLINED ABOVE ARE INDICATIVE OF A POTENTIAL SHOCK HAZARD AND MUST BE CORRECTED BEFORE RETURNING THE APPLIANCE TO THE CUSTOMER. 2. PRODUCT SAFETY NOTICE Many electrical and mechanical parts in the appliance have special safety related characteristics

9、. These are often not evident from visual inspection nor the protection afforded by them necessarily can be obtained by using replacement components rated for voltage, wattage, etc. Replacement parts which have these special safety characteristics are identified in this Service Manual. Electrical co

10、mponents having such features are identified by marking with a on the schematics and on the parts list in this Service Manual. The use of a substitute replacement component which does not have the same safety characteristics as the PIONEER recommended replacement one, shown in the parts list in this

11、 Service Manual, may create shock, fire, or other hazards. Product Safety is continuously under review and new instructions are issued from time to time. For the latest information, always consult the current PIONEER Service Manual. A subscription to, or additional copies of, PIONEER Service Manual

12、may be obtained at a nominal charge from PIONEER. Leakage current tester Reading should not be above 0.5 mA Device under test Test all exposed metal surfaces Also test with plug reversed (Using AC adapter plug as required) Earth ground AC Leakage Test (FOR USA MODEL ONLY) RadioFans.CN 收音机爱 好者资料库 3VS

13、X-1130-K 5678 5678 A B C D E F CONTENTS SAFETY INFORMATION.2 1. SERVICE PRECAUTIONS.4 1.1 NOTES ON SOLDERING.4 1.2 SERVICE NOTICE.4 2. SPECIFICATIONS.5 3. BASIC ITEMS FOR SERVICE .6 3.1 CHECK POINTS AFTER SERVICING .6 3.2 JIGS LIST.6 3.3 PCB LOCATIONS.7 4. BLOCK DIAGRAM .10 4.1 OVERALL WIRING DIAGRA

14、M .10 4.2 AUDIO BLOCK DIAGRAM.12 4.3 DMAIN BLOCK DIAGRAM (AUDIO).14 4.4 VIDEO BLOCK DIAGRAM.16 4.5 DMAIN BLOCK DIAGRAM (VIDEO).18 4.6 POWER SUPPLY BLOCK DIAGRAM.20 4.7 GND BLOCK DIAGRAM.22 5. DIAGNOSIS .24 5.1 TROUBLESHOOTING.24 5.2 CONFIMATION OF THE NETWORK MODULE.30 5.3 ERROR INDICATIONS.32 5.4 P

15、ROTECTION CIRCUIT.34 6. SERVICE MODE.36 6.1 TEST MODE.36 6.2 DEFAULT SETTINGS .38 7. DISASSEMBLY .39 8. EACH SETTING AND ADJUSTMENT.48 8.1 ADJUSTMENT REQUIRED WHEN THE UNIT IS REPAIRED OR REPLACED.48 8.2 USB BACKUP.49 8.3 UPDATING OF THE FIRMWARE.50 8.4 IDLE CURRENT ADJUSTMENT.53 9. EXPLODED VIEWS A

16、ND PARTS LIST.54 9.1 PACKING SECTION.54 9.2 EXTERIOR SECION.56 RadioFans.CN 收音机爱 好者资料库 4VSX-1130-K 1234 A B C D E F 1234 1. SERVICE PRECAUTIONS 1.1 NOTES ON SOLDERING 1.2 SERVICE NOTICE For environmental protection, lead-free solder is used on the printed circuit boards mounted in this unit. Be sure

17、 to use lead-free solder and a soldering iron that can meet specifications for use with lead-free solders for repairs accompanied by reworking of soldering. Compared with conventional eutectic solders, lead-free solders have higher melting points, by approximately 40 C. Therefore, for lead-free sold

18、ering, the tip temperature of a soldering iron must be set to around 373 C in general, although the temperature depends on the heat capacity of the PC board on which reworking is required and the weight of the tip of the soldering iron. Do NOT use a soldering iron whose tip temperature cannot be con

19、trolled. Compared with eutectic solders, lead-free solders have higher bond strengths but slower wetting times and higher melting temperatures (hard to melt/easy to harden). The following lead-free solders are available as service parts: Parts numbers of lead-free solder: GYP1006 1.0 in dia. GYP1007

20、 0.6 in dia. GYP1008 0.3 in dia. For more detail, please refer to 7. DISASSEMBLY - 1. Discharging. As the screw covers for the speaker terminals are subject to breakage, be careful when removing them. If a screw cover is broken during removal, replace it with a new one. Continuous use of a broken sc

21、rew cover may cause short-circuiting of speaker terminals. Discharging Notice of the Parts exchange RadioFans.CN 收音机爱 好者资料库 5VSX-1130-K 5678 5678 A B C D E F 2. SPECIFICATIONS Amplifier section Continuous average power output of 100 watts* per channel, min., at 8 ohms, from 20 Hz to 20 000 Hz with n

22、o more than 0.08 %* total harmonic distortion. Front (stereo).100 W + 100 W Power output (1 kHz, 6 , 1 %, 1 ch driven) . 165 W Guaranteed speaker impedance.6 to 16 * Measured pursuant to the Federal Trade Commissions Trade Regulation rule on Power Output Claims for Amplifiers * Measured by Audio Spe

23、ctrum Analyzer Audio Section Input (Sensitivity/Impedance) LINE.315 mV/47 k Signal-to-Noise Ratio (IHF, short circuited, A network) LINE.101 dB Tuner Section Frequency Range (FM) .87.5 MHz to 108 MHz Antenna Input (FM).75 unbalanced Frequency Range (AM) .530 kHz to 1 700 kHz Antenna (AM) .Loop anten

24、na (balanced) Video Section Signal level Composite Video.1 Vp-p (75 ) Component Video. Y: 1.0 Vp-p (75 W), PB/PR: 0.7 Vp-p (75 ) Corresponding maximum resolution Component Video.1080p (1125p) Bluetooth Section Version.Bluetooth Specification Ver. 2.1 + EDR Output.Bluetooth Specification Class 2 Esti

25、mated line-of-sight transmission distance*.About 10 m * The line-of-sight transmission distance is an estimate. Actual transmission distances supported may differ depending on surrounding conditions. Frequency range. 2.4 GHz Supported Bluetooth profiles.A2DP, AVRCP Supported Codec .SBC (Subband Code

26、c), AAC Digital In/Out Section HDMI terminal .19-pin (Not DVI) HDMI output type. 5 V, 55 mA HDMI input/MHL terminal. 5 V, 900 mA USB terminal .USB2.0 High Speed (Type A) 5 V, 1 A iPod terminal.USB Integrated Control Section Control (IR) terminal. 3.5 Mini-jack (MONO) IR signal. High Active (High Lev

27、el: 2.0 V) Network Section (Wired) LAN terminal.10 BASE-T/100 BASE-TX Network Section (Wireless) WLAN standards . IEEE 802.11a, IEEE 802.11b, IEEE 802.11g, IEEE 802.11n Frequency band 2.4 GHz band (2.412 GHz to 2.462 GHz).Channel 1 to Channel 11 5 GHz band (5.180 GHz to 5.240 GHz, 5.745 GHz to 5.825

28、 GHz). Channel 36 to Channel 48, Channel 149 to Channel 165 Security.Disabled (no encryption) WEP (Key length: 64 bit/128 bit, Key format: ASCII/Hex) WPA2 Mixed (WPA/WPA2, Encryption method: TKIP/AES, Recognition method: PSK) Miscellaneous Power requirements.AC 120 V, 60 Hz Power consumption. 550 W In standby. 0.1 W In standby (HDMI control on). 0.3 W In standby (Network standby on). 2.7 W In standby (Network standby on, wireless LAN connected) . 3.0 W In standby (HDMI control on, Network standby on). 2.7 W In standby (HDMI control on, Net