JBL-DVD600MK2-cd-sm维修电路原理图.pdf

《JBL-DVD600MK2-cd-sm维修电路原理图.pdf》由会员分享，可在线阅读，更多相关《JBL-DVD600MK2-cd-sm维修电路原理图.pdf（63页珍藏版）》请在收音机爱好者资料库上搜索。

1、 Model DVD600IIDVD600II DVD/CD/CD-R/CD-RW/VCD Changer From the Cinema Propack 600II System Service Manual CONTENTS SPECIFICATIONS.2 SET-UP GUIDE.4 FRONT PANEL CONTROLS.7 FRONT PANEL DISPLAY.8 REAR PANEL CONNECTIONS.9 REMOTE CONTROL FUNCTIONS.10 OPERATION.14 BASIC TROUBLESHOOTING.21 EXPLODED VIEW.24

2、EXPLODED/MECHANICAL PARTS LIST25 SERVICE BULLETIN JBL2002-01.26 SERVICE BULLETIN JBL2003-01.28 SERVICE BULLETIN JBL2003-07.29 TECH TIP JBLTT2003-03.30 BLOCK DIAGRAM.31 IC901 MICROPROCESSOR.32 ELECTRICAL PARTS LIST38 PACKAGING44 PCB DRAWINGS.45 POWER SUPPLY50 SCHEMATICS.55 WIRING DIAGRAM.63 JBL Consu

3、mer Products 250 Crossways Park Dr. Woodbury, New York 11797 Rev2 9/2005 RadioFans.CN 2 Playback Media:5-inch (12cm) or 3-inch (8cm) DVD-Video: Region 1, single or dual sides/layers, linear PCM, Dolby Digital or DTS CD, CD-R, CD-RW: Linear PCM Audio MP3 Video CD (VCD): MPEG-1 Video, Linear PCM Audio

4、 Video Section: Signal format:NTSC Composite Output:1V p-p/75 ohms, sync, negative polarity S Output:Y/Luminance: 1V p-p/75 ohms, sync, negative polarity C/Chrominance: 0.286V p-p Component Outputs:Y: 1V p-p/75 ohms, sync, negative polarity Pr: 0.648V p-p/75 ohms Pb: 0.648V p-p/75 ohms Audio Section

5、: Coaxial Digital Output:0.5V p-p/75 ohms Frequency Response:2Hz to 22kHz, +/ 0.5dB (44.1kHz sampling rate) Dynamic Range:DVD: 105dB (20-bit) CD: 100dB Channel Separation:90dB THD:0.0035% Signal-to-Noise Ratio:100 dB Wow and Flutter:below measurable limits General: Unit Power Consumption:25W Unit Di

6、mensions:Width: 17.3 inches (440mm) Height: 5.1 inches (130mm) Depth: 16.9 inches (420mm) Unit Weight:14.4 lb (7.6kg) Depth measurement includes knobs and buttons. Height measurement includes feet and chassis. All features and specifications are subject to change without notice. Technical Specificat

7、ions DVD600II This product incorporates copyright protection technology that is protected by method claims of certain U.S. patents and other intellectual property rights owned by Macrovision Corporation and other rights owners. Use of this copyright protection technology must be authorized by Macrov

8、ision Corporation and is intended for home and other limited viewing uses only, unless otherwise authorized by Macrovision Corporation. Reverse engineering or disassembly is prohibited. DVD600II DVD600II RadioFans.CN DATE:SEP 26.2001 1. Audio * Test Disc : YEDS 7(Sony),EIAJ CD- 1 Coaxial(75) 2. Vide

9、o(75? Terminated) - - - NTSC VIDEO * Test Disc : Navigation Vol 1 FOR SYSTEM(DVD- NF200) * VM700T C- Video Output level Y/Cb/Cr Video RCA JACK S/N S- JACK S/N RCA JACK Freq. Resp. S- JACK Freq.Resp Video S/N 100% Flat Video S/N 50% Flat 100% Color Bar WTD : Off, SC TRAP On BPF : 100KHz 5.0MHz 100% C

10、olor Bar 1 - 1 - 8 - LPF : 500KHz 1 - 1 - 1 HPF : 10KHz 75% Color Bar Data Frequency Response Nominal Spec Norminal Spec 40 IRE 1.0V 0.1(p- p) 1.0V 0.1(p- p) Frequency Response C- Video S - Video C- Video S - Video C- Video S - Video C- Video S - Video Cr Output Level 0.286V(p- p) 20% 02.5dB 55dB60d

11、B 1.0V(p- p) 10% Cb Output Level0.7V(p- p) 20% Y Output Level 0.7V(p- p) 20% Color Burst Error 55dB Color S/N AM/PM 150Hz120Hz 60dB Color S/N AM/PM RCA Jack Color S/N S- Jack Color S/N Output Level Item (Y)Output Level S - Video (C)Output Level RCA JACK Level ItemTest TrackTest ConditionsLimite Spec

12、 1 Limite SpecTest ConditionsTest Trac 0.5 + 0.05V(p- p) 1 - 1 - 7 100% Flat 100% Flat 1 - 1 - 7 100% Flat Data 100% Red Color 4.2 MHz0.5MHz(NTSC) Multiburst 1 - 1 - 6 1 - 1 - 1 1 - 1 - 8 - 1 - 1 - 1 DVD600II DVD600II RadioFans.CN 3 4 Quick Installation Diagrams BASIC INSTALLATION: Your TV must at a

13、 minimum have a composite video input (this connector usually has a yellow-colored core), and Left (usually has a white-colored core) and Right (red-colored core) Stereo audio preamp-level RCA outputs. All wires for this hookup are included. TV VIDEO IN AUDIO IN L R AUDIO OUT L R VIDEO OUT S-VIDEO I

14、NS-VIDEO OUT COMPONENT VIDEO IN Pr Pb Y White Red DCR600II DVD600II CONNECT TO AC OUTLET CONNECT TO AC OUTLET Yellow YellowBlackOrange NOTES: 1. CONNECT “RIDGED” WIRE TO (+) COLORED TERMINAL AND CONNECT “SMOOTH” WIRE TO () BLACK TERMINAL ON DCR600II AND SPEAKERS. 2. WIRE COLOR CODES ARE FOR EASE OF

15、CONNECTION. THE SPEAKER WIRES CAN BE INTERCHANGED IF NECESSARY. (+) Ridges + SURROUND RIGHT SPEAKER + SURROUND LEFT SPEAKER + FRONT RIGHT SPEAKER + FRONT LEFT SPEAKER + CENTER SPEAKER + SUBWOOFER GrayGreenRedWhiteBrownBlue DVD600II DVD600II 5 Quick Installation Diagrams TV VIDEO IN AUDIO IN L R AUDI

16、O OUT L R VIDEO OUT S-VIDEO INS-VIDEO OUT COMPONENT VIDEO IN Pr Pb Y White Red DCR600II DVD600II CONNECT TO AC OUTLET CONNECT TO AC OUTLET BlackOrange ()(+) Ridges + SURROUND RIGHT SPEAKER + SURROUND LEFT SPEAKER + FRONT RIGHT SPEAKER + FRONT LEFT SPEAKER + CENTER SPEAKER + SUBWOOFER ALTERNATE INSTA

17、LLATION FOR BETTER PICTURE QUALITY: Your TV must have an S-Video input, and Left (usually has a white-colored core) and Right (red-colored core) Stereo audio preamp-level RCA outputs. Two pieces of S-Video cable are not included and should be purchased separately. NOTES: 1. CONNECT “RIDGED” WIRE TO

18、(+) COLORED TERMINAL AND CONNECT “SMOOTH” WIRE TO () BLACK TERMINAL ON DCR600II AND SPEAKERS. 2. WIRE COLOR CODES ARE FOR EASE OF CONNECTION. THE SPEAKER WIRES CAN BE INTERCHANGED IF NECESSARY. S-Video cable not included S-Video cable not included GrayGreenRedWhiteBrownBlue DVD600II DVD600II 6 Quick

19、 Installation Diagrams TV VIDEO IN AUDIO IN L R AUDIO OUT L R VIDEO OUT S-VIDEO INS-VIDEO OUT COMPONENT VIDEO IN Pr Pb Y White Red DCR600II DVD600II CONNECT TO AC OUTLET CONNECT TO AC OUTLET Yellow Black Orange (+) Ridges + SURROUND RIGHT SPEAKER + SURROUND LEFT SPEAKER + FRONT RIGHT SPEAKER + FRONT

20、 LEFT SPEAKER + CENTER SPEAKER + SUBWOOFER Yellow ALTERNATE INSTALLATION FOR BEST PICTURE QUALITY: Your TV must have Y/Pr/Pb component video inputs (three separate RCA connectors with red-, blue- and green-colored cores), and Left (usually has a white-colored core) and Right (red-colored core) Stere

21、o audio preamp-level RCA outputs. The component video cable is not included and should be purchased separately. This setup requires that the TVs own video switching is utilized to access the DVD picture. All other video switching is still done through the DCR600II. NOTES: 1. CONNECT “RIDGED” WIRE TO

22、 (+) COLORED TERMINAL AND CONNECT “SMOOTH” WIRE TO () BLACK TERMINAL ON DCR600II AND SPEAKERS. 2. WIRE COLOR CODES ARE FOR EASE OF CONNECTION. THE SPEAKER WIRES CAN BE INTERCHANGED IF NECESSARY. 3. MUST USE VIDEO SWITCHING THROUGH TV TO ACCESS COMPONENT VIDEO. GrayGreenRedWhiteBrownBlue Composite Vi

23、deo cable not included DVD600II DVD600II 7 DVD600IIFront Panel Controls Main Power Switch: Press this button to apply power to the DVD600II. When the switch is pressed in, the unit is placed in a Standby mode, as indicated by the amber Power Indicatorsurrounding the System Power Control. This button

24、 MUST be pressed in to operate the unit. To turn the unit off and prevent the use of the remote control, this switch should be pressed until it pops out from the front panel so that the word “OFF” may be read at the top of the switch. NOTE: This switch is normally left in the “ON” position. System P

25、ower Control: When the Main Power Switchis “ON,” press this button to turn on the DVD600II; press it again to turn the unit off. Note that the Power Indicatorin the center of the switch will turn green when the unit is on. Power Indicator: This LED will be illu- minated in amber when the unit is in

26、the Standby mode to signal that the unit is ready to be turned on. When the unit is in operation, the indicator will turn green. Disc Tray: Holds up to five DVD or CD discs that can be played one at a time in the DVD600II. Disc Skip: Press twice in quick succes- sion to change the disc being played.

27、 This will move the tray forward to the next occupied position, skipping over the empty-disc positions. Search Forward/Reverse: Press to move forward or backward through a disc at one of four speeds. Each press and release will increase the search speed, as indicated in the on-screen display. Once y

28、ou have selected the desired speed, release the button and the disc will continue to search at fast speed. To resume normal playback speed, press the Play Button . Open/Close Button: Press to open or close the Disc Tray . Upon closing the disc tray, the On Screen Library system will begin to identif

29、y all loaded discs. Skip Forward/Reverse: Press to move forward or backward through the music tracks or chapters on a disc. Stop: Press once to place the disc in the Resume mode, which means that playback will stop, but (as long as the tray is not opened or the disc changed) DVD playback will contin

30、ue from the same point on the disc when the Play button is pressed again. Resume will also work if the unit was turned off. To stop a disc and have play start from the beginning, press the button twice. Play/Pause: Press to begin playback of a disc, or to momentarily pause playback. If a DVD is play

31、ing, action will freeze and a still picture will be displayed when the button is pressed. Direct Access Buttons: Press one of these buttons to play any of the five discs loaded in the Disc Tray. Information Display: This display con- tains a variety of indicators that provide infor- mation about the

32、 status of the DVD600IIand the disc currently playing. Display Dim: Press this button to adjust the brightness of the Information Display by 50% or to turn the display off completely in the following order: FULL BRIGHTNESS HALF BRIGHTNESS OFF FULL BRIGHTNESS. Remote Sensor: The sensor that receives

33、the infrared commands from the remote control is behind this area. Do not cover or obscure this part of the front panel, in order to avoid a malfunction with the remote. 96KHz 24bit DVD600II DVD600II 8 DVD600IIFront Panel Information Display Disc Type: Lights to show the type of disc currently being

34、 played. Disc Number: Shows if a disc is loaded in a tray position. The indicator for the disc in play flashes. Note that if a disc is added to or removed from the tray while a disc is playing, the indicator will not show the change until all discs are cycled. Title: Shows the DVD title number curre

35、ntly playing. Chapter/Track Number: Shows the current chapter (DVD) or current track number (CD). Program Time: Shows the running time of a DVD; current track time; time remaining in the current track; or the total remaining time of a CD. NOTE: The Program Time Indicators will also display text mess

36、ages about the DVD600IIs status, including Reading when a disc is loading, Bye when the unit is turned off, and Disc Error when a disc not compatible with the DVD600IIis put into the play position. Intro: Lights when the IntroScan function is active. Program: Lights during programming. Repeat: Light

37、s to indicate any of the Repeat modes. Random: Lights when the unit is in the Random Play mode. Resume: Lights when the Stop button has been pressed once to put the unit in the Resume mode. Playback Mode: Lights to show the cur- rent playback mode: Lights when a disc is playing in the Normal mode. L

38、ights when the disc is in the Fast Search Forward mode. For DVDs, when both triangles glow steadily, the disc plays at 2x normal speed. When the right triangle is flashing, the disc plays at 4x normal speed. When the left triangle is flashing, the disc plays at 8x normal speed. When both triangles a

39、re flashing, the disc plays at 16x normal speed. For CDs, only the first three Fast Search modes are available. Lights when the disc is paused. Lights when the disc is in the Fast Search Reverse mode. For DVDs, when both triangles glow steadily, the disc plays at 2x normal speed. When the left trian

40、gle is flashing, the disc plays at 4x normal speed. When the right triangle is playing, the disc plays at 8x normal speed. When both triangles are flashing, the disc plays at 16x normal speed. For CDs, only the first three Fast Search modes are available. Parental Lock Indicator: This indicator ligh

41、ts when the parental-lock system is engaged in order to prevent anyone from changing the rating level without a code. 96kHz/24-Bit Indicator: When a high- resolution, linear PCM bitstream with a sam- pling rate of 96kHz/24 bits is detected, this indicator will light. Such a selection may be found as

42、 an alternative audio track on a DVD- Audio disc. M 96KHz 24bit DVD600II DVD600II 9 Component Video Outputs: If your TV or video projector has component video inputs, you may connect these output jacks to the set for the highest video quality available. Note that the component video inputs may be la

43、beled as Y/Pr/Pb or Y/Cr/Cb but, for connec- tion purposes, they are the same. The outputs of these jacks should NOT be connected to a standard composite video input. S-Video Output: Connect this jack to the S-Video input on a television or video projector, or to an S-Video input on an A/V receiver

44、or processor if you are using that type of device for S-Video input switching. Composite Video Output: Connect this jack to the video input on a television or video projector, or to a video input on an A/V receiver or processor if you are using that type of device for video input switching. Coaxial

45、Digital Output: Connect this jack to the coaxial digital input of an A/V receiver or surround processor for Dolby Digital, DTS or PCM audio playback. NOTE: The coaxial digital output should only be connected to a digital input. Even though it is the same RCA-type connector as standard analog audio c

46、onnections, DO NOT connect it to a conventional analog input jack. Remote Control Output: Connect this jack to the infrared (IR) input jack of another JBL (or other compatible) remote-controlled product to have the built-in Remote Sensor on the DVD600IIprovide IR signals to other compatible products

47、. Remote Control Input: Connect the out- put of a remote infrared sensor, or the remote control output of another JBL (or other compat- ible) product, to this jack. This will enable the remote control to operate even when the front panel Remote Sensor is blocked. This jack may also be used with comp

48、atible IR remote control-based automation systems. AC Power Cord: Connect this plug to an AC outlet. If the outlet is controlled by a switch, make certain that it is in the ON position. DVD600IIRear Panel Connections DVD600II DVD600II 10 Remote Control Functions IMPORTANT NOTE: The remote control for the JBL Cinema ProPack 600IImay be pro- grammed to control up to eight devices, includ- ing the DCR600IIand DVD600II. It is helpful to think of the remote as being organize