Infinity-Overture2-ps-sm维修电路原理图.pdf
《Infinity-Overture2-ps-sm维修电路原理图.pdf》由会员分享,可在线阅读,更多相关《Infinity-Overture2-ps-sm维修电路原理图.pdf(35页珍藏版)》请在收音机爱好者资料库上搜索。
1、Compositions Series Overture 2 Powered Loudspeakers Service Manual Infinity Systems, Inc 250 Crossways Park Dr. Woodbury, New York 11797 Rev1 5/2004 RadioFans.CN TABLE OF CONTENTS SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 DETAILED SPECIFICATIONS . .
2、. . . . . . . . . . . . . . . . . . . . . . . . . .4 WIRING THE SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 OPERATING THE SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6 REPLACING THE FUSE . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3、 . . . .7 CARE OF YOUR SPEAKER SYSTEM/TROUBLESHOOTING . . .10 MECHANICAL/PACKAGING PARTS LIST . . . . . . .11 EXPLODED VIEW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12 PACKAGING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13 SERVICE BULL
4、ETIN INF9704 NOV. 1997 .14 SERVICE BULLETIN INF9705 NOV. 1997 . . . . . . . . . . . . . . .16 TEST SET UP AND PROCEDURE . . . . . . . . .17 NOTE ON OVTR 2/3 AMPLIFIER REVISION.18 PCB DRAWINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19 ELECTRICAL PARTS LIST (120V) .
5、 . . . . . . . . . . . . . . .21 ELECTRICAL PARTS LIST (230V) . . . . . . . . . . . . . . . . . . . . . . . . . .24 INTEGRATED CIRCUIT DIAGRAMS . . . . . . . . . . . . . . . . . . . . . . . .27 WIRING DIAGRAM/CROSSOVER NETWORK SCHEMATIC (120V) . . .28 WIRING DIAGRAM/CROSSOVER NETWORK SCHEMATIC (230V
6、) . . .29 120V SCHEMATICS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30 230V SCHEMATICS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33 Infinity continually strives to update and improve existing products, as well as create new ones. The spec
7、ifications and construction details in this and related Infinity publications are therefore subject to change without notice. Overture 2 2 RadioFans.CN Overture 2 3 Specifications Frequency Response: 30Hz - 20,000Hz (3dB) Recommended Amplifier Power Range 10-150 watts Amplifier Peak Output:300VA Max
8、imum Output:112 dB SPL Sensitivity:93dB 2.83V 1 meter Nominal Impedance:8 Crossover Frequencies:350 and 3,000Hz Low-Frequency Driver:(2) 6 1/2” (165MM) high-efficiency, dynamically-balanced, magnetically shielded woofers. Mid-Bass Driver:(2) 5 1/4” (125mm) high-efficiency, magnetically shielded midr
9、ange drivers High-Frequency Driver:1” (25mm) soft dome, high-efficiency, neodymium magnet, magnetically shielded tweeter Dimensions (H x W x D):38-3/4” x 6-7/8 x 15-3/4 (984mm x 175mm x 400mm) Weight:47 lb./(21.4 kg) Each Power Consumption:150 watts (Maximum) * The maximum recommended amplifier powe
10、r rating will ensure proper system headroom to allow for occasional peaks. We do not recommend sustained operation at these maximum power levels. RadioFans.CN Detailed Specifications Overture 2 4 Overture 2 5 Wiring The System Overture 2 6 Operating The System Overture 2 7 Replacing The Fuse Overtur
11、e 2 8 Replacing The Fuse (Cont.) Overture 2 9 Replacing The Fuse (Cont.) UTILSER UN FUSIBLE DE RECHANGE DE MEME TYPE ET CALIBRE FOR CONTINUED PROTECTION AGAINST RISK OF FIRE, REPLACE ONLY WITH SAME TYPE OF FUSE: T1.6A 250V CAUTION:ATTENTION: POWERFUSE T 1.6A 250V 230V 50Hz 150W MAX 00435 F U S E F U
12、 S E FUSE T3, 1.6A 250V OVTR 2 with speaker cables connect the amplifiers output to the UUT Speaker binding posts. 2.On the UUT, turn the BASS (level) control full counterclockwise (1). 3.Turn on generator, adjust so that the output at the Integrated amplifier is 1.0V, 30 Hz. 4.Plug in UUT; LED shou
13、ld be Red. Turn BASS (level) control full clockwise (9). 5.LED should now be Green and immediate bass response should be heard (and observed if the grille is removed). Sweep Function 6.Follow steps 1-5 above. 7.Sweep generator from 20Hz to 300Hz. Listen to the cabinet and drivers for any rattles, cl
14、icks, buzzes or any other noises. If any unusual noises are heard, remove woofers and test. Driver Function 8.Remove woofer from cabinet; detach + and - wire clips. 9.Check DC resistance of woofer; it should be: (120v) - 14.1 Ohms 10% (230v) - 40.0 Ohms 10% 10. Connect a pair of speaker cables to dr
15、iver terminals. Cables should be connected to a high-gain integrated amplifier fed by a signal generator. Turn on generator and adjust so that speaker level output is 20.0V. * 11. Sweep generator from 20Hz to 1kHz. Listen to driver for any rubbing, buzzing, or other unusual noises. * Only the 120v v
16、ersion will be driven to near maximum excursion at this voltage; because of the unusually high DCR of the voice coil, driving the 230v version at twice this voltage is not practical with simple test equipment and 20v should suffice for test purposes. Amplifier bias adjustment 1)Power up loudspeaker
17、and drive at low levels for 3 minutes for warm-up. 2)Remove amplifier assembly (disassembly procedure in bulletin INF9704 Page 15). 3)Power up on the bench; attach DMM (on low DC voltage range) across TP1 and TP2 on schematic R77 - (120v) .22 5W fuse resistor. (230v) .47 5W fuse resistor. Mini-grabb
18、ers can be used on the resistor leads without PCB removal. 4)Adjust POT2 (bias pot on PCB) to read 5.9 mV for both 120v and 230v units. IMPORTANT NOTE ON OVTR 2/3 AMPLIFIER REVISION There was an early version of the Overture 2 and 3 Amplifier that is represented slightly inaccurately in the schemati
19、c, PCB drawings, and parts list in this service manual. This page is a guide to the identification and differences to this earlier version. The drawing below is a later version of the PCB, complete with this information. NLA = No Longer Available ORIGINAL VERSION = R80 IS NOT IN SILKSCREENED AREA, B
20、UT INSTEAD ON OPPOSITE SIDE OF PCB, CONNECTED FROM MAIN “+” ON C15, TO COLLECTOR (CENTER LEAD) ON Q12 (BF469). Q11 ORIGINAL VERSION = MPSU06 Q11 LATER VERSION = 2SD2012 (DO NOT SUBSTITUTE - PIN LAYOUT DIFFERENT !) MPSU06 part# NLA ORIGINAL VERSION = TWO RELAYS LATER VERSION = ONE RELAY Do not mistak
21、e T1 for a relay. (Later version has speaker output terminals in footprint of former relay) There was also a version with two relays that had the output terminals on the indicted relay bypassed with buss wire, rendering it inoperative. ORIGINAL RELAY part# NLA R43,43b ORIGINAL VERSION = 13K 1/2W R43
22、,43b LATER VERSION = 33K 1/2W 13K 1/2W part# NLA Overture 2 18 Bass Amplifier PCB, Padmaster & Solder Side Overture 2 19 Bass Amplifier PCB Component Side Silkscreen Overture 2 20 Semiconductors DI1004Diode Zener 6.2V 1/2W T/RZD21 DI1060Diode Switching 500mW 75VD1,2,4,5,6,7,9,118 DI1089Diode 1N4003
23、1A 200 PIVD101 DI1101Diode Zener 10V 1/2W T/RZD3,4,5,64 DI1186Diode Zener 36V 5% 5W T/RZD11 DI1187Diode Bridge Powr 400V/8AD181 IC1215IC TL064CN Quad OP AMPU1,22 IC1216IC TL062CP Dual OP Amp.U31 IC1045Three-Term. Adj. Pos. V R LM317TU41 604-L469EGWLED Green/Red Common Cath1 TR1002Transistor NPN TO-9
24、2 2N3904Q1,5,73 TR1017Transistor PNP T/R 2N3906Q2,3,6,84 TR1257MOSFET Power IRFS250Q13,14,15,164 TR1259Transistor NPN BF469Q4,9,123 TR1260Transistor PNP BF470Q101 TR1304Transistor NPN 60V/3A 25W 2SD2012Q111 Capacitors CP1126Cap Poly Film 1uF 10% 50VC191 CP1630Cap Alum El 220uF 20% 25vC201 CP1656Cap
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- Infinity Overture2 ps sm 维修 电路 原理图