《HarmanKardon-SUBTS7-pwr-sm维修电路原理图.pdf》由会员分享,可在线阅读,更多相关《HarmanKardon-SUBTS7-pwr-sm维修电路原理图.pdf(33页珍藏版)》请在收音机爱好者资料库上搜索。
1、harman/kardon SUB-TS7(HKTS 7 SUBWOOFER) SUB-TS8(HKTS 8 SUBWOOFER) SERVICE MANUAL harman/kardon, Inc. 250 Crossways Park Dr. Woodbury, New York 11797 Rev1 10/2006 RadioFans.CN CONTENTS BASIC SPECIFICATIONS . . . . . . . . . . . . . . . . 1 DETAILED SPECIFICATIONS . . . . . . . . . . . . . . . . . . .
2、 . . . . 2 CONTROLS or whether it has moved: i.e., the speaker that was not working still has no sound and the speaker that was working is still fine. If the problem is in the same place, the source of the problem is most likely with your receiver or amplifier, and you should consult the owners manu
3、al for that product for further information. If theproblem has followed the speaker, consult your dealer for further assistance or, if that is not possible, visit our Web site at for further information. If there is no sound from Check all wires and connections between receiver/amplifier and speaker
4、. Make sure all wires are connected. the center speaker:Make sure none of the speaker wires are frayed, ccut, punctured, or touching other wires. If your receiver/processor is set in Dolby Pro Logic mode, make sure the center speaker is not in phantom mode. If your receiver/processor is set in Dolby
5、 Digital or DTS mode, make sure the receiver/processor is configured so that the center speaker is enabled. If the system plays at low Check all wires and connections between receiver/amplifier and speakers. Make sure all wires are connected. volumes but shuts off as Make sure none of the speaker wi
6、res are frayed, cut, punctured, or touching other wires. volume is increased: If more than one pair of main speakers is being used, check the minimum impedance requirements of your receiver/amplifier. If there is low (or no) bass Make sure the SUB or Line-Level Inputs of the subwoofer and SUB or LFE
7、 output of your receiver output:or amplifier are properly connected by the RCA-type interconnect cable. If you are using the Subwfrs Speaker-Level Inputs , check your speaker cables to make sure they are all connected; that none of the wires are frayed, cut, punctured, or touching other wires; and t
8、hat you have maintained the correct polarity by connecting positive terminals to positive terminals, and negative terminals to negative terminals. Make sure the subwoofer is plugged into an active electrical outlet and its Master Power Switch is switched on to the “” position. Check the speaker setu
9、p (bass management) settings in your A/V receiver or processor to make certain that the front, center and surround speakers are configured for “Small,” and that the subwoofer is set for “Yes” or “On.” If there is no sound from Check all wires and connections between receiver/amplifier and speakers.
10、Make sure all wires are connected. Make sure the surround speakers:none of the speaker wires are frayed, cut, punctured, or touching other wires. Review proper operation of your receiver/processor and its surround sound features. Make sure the movie or TV show you are watching is recorded in a surro
11、und sound mode. If it is not, check to see whether your receiver/processor has other surround modes you may use. In Dolby Digital or DTS mode, make sure your receiver/processor is configured so that the surround speakers are enabled. Review the operation of your DVD player and the jacket of your DVD
12、 to make sure that the DVD features the desired Dolby Digital or DTS mode, and that you have properly selected that mode using both the DVD players menu and the DVD discs menu. SUB-TS7/TS8 harman/kardonSUB-TS7/TS8 harman/kardon 10 Ref# Description Part Number Qty 1 Amplifier screw 352-AM04020D210 10
13、 2 SUB-TS7/TS8 Amplifier Not for Sale 1 3 Port Tube Not for Sale 1 4 SUB-TS7/TS8 Cabinet Not for Sale 1 5 Logo 316-AG-00557 1 6 LED Not for Sale 1 7 Grille Not for Sale 1 8 Logo 316-AL-00553 1 9 10 woofer 25PF12DZB-DW01 1 10 Woofer screw 352-FM04020D605 5 11 Foot Pad 320-EVA-00057 4 SUB-TS7/TS8 harm
14、an/kardon SUB-TS7/TS8 harman/kardon 11 (See Mechanical Parts List on Pages 21-22) SUB-TS7/TS8 harman/kardonSUB-TS7/TS8 harman/kardon 12 Test Set Up and Procedure Equipment needed: Function/signal generator/sweep generator Integrated Amplifier Multimeter Speaker cables Initial Control Settings: Power
15、 Switch OFF; Filter OFF Level MIN (Full CCW) Phase, Auto/On switches do not matter General Unit Function (UUT = Unit Under Test) 1) From the signal generator, connect one line level (RCA) cable to the Subwoofer Line Level Input jacks L/R on the UUT. Use a Y-cable from a mono source if necessary to c
16、onnect to both inputs. Do not connect to the single, purple SUB input. 2) Turn on generator; adjust to 75mV, 50 Hz. 3) Plug in UUT; turn the power switch ON. Turn LEVEL control full clockwise (MAX) 4) LED should turn from Amber to Blue (on top of UUT); immediate and vigorous bass response should be
17、heard and felt from port tube opening. 5) Turn off generator, turn LEVEL control full counterclockwise (MIN), and disconnect RCA cable. 6) Connect one pair of speaker cables to Speaker Level input terminal (IN) on UUT. Cables should be connected to an integrated amplifier fed by the signal generator
18、. 7) Turn on generator and adjust so that speaker level input at the amplifier is 1.6V, 50 Hz. Turn LEVEL control full clockwise. 8) LED should turn from Amber to Blue; immediate and vigorous bass response should be heard and felt from the port tube opening. Sweep Function 1) Follow steps 6-8 above,
19、 using a sweep generator as a signal source. 2) Sweep generator from 20Hz to 300Hz. Listen to the cabinet and drivers for any rattles, clicks, buzzes or any other noises. If any unusual noises are heard, remove woofers and test. Driver Function 1) Remove woofer from cabinet; detach + and - wire clip
20、s. 2) Check DC resistance of woofer; it should be 3.0 ohms 10% 3) Connect a pair of speaker cables to driver terminals. Cables should be connected to an integrated amplifier fed by a signal generator. Turn on generator and adjust so that speaker level output is 5.0V. 4) Sweep generator from 20Hz to
21、1kHz. Listen to driver for any rubbing, buzzing, or other unusual noises. SUB-TS7/TS8 harman/kardonSUB-TS7/TS8 harman/kardon 13 harman/kardon TECH TIPSTECH TIPS Troubleshooting tips and solutions to common service problems For models: HKTS7 SUB (SUB-TS7) TIP# HKTT2004-04 Subject: Improved filter per
22、formance Instructions: Change four 1/6W 5% CF Resistors in the PREAMP PCB of the HKTS 7 subwoofer amplifier. It is recommended this procedure be followed for every unit that has to be serviced, for any reason. Designator Original value New value h/k part number R223 51k 30k R224 51k 30k 110-16303J26
23、 R226 27k 10k 110-16103j26 R227 27k 12k 110-16123j26 NOTE: Lack of this modification is unlikely to generate a complant It will have no effect in applications when the SUB input is used, or when the sub amp is used with the FILTER switch in the OFF position. Model Serial Number (120v) Serial Number
24、(230v) Status Action SUB-TS7 ME048503390 and below ME048708198 and below In need of filter modification Change value of R223,224,226,227 SUB-TS7 ME048503391 and above ME048708199 and above Modified by Factory None Required SUB-TS7/TS8 harman/kardonSUB-TS7/TS8 harman/kardon 14 SUB-TS7/TS8 harman/kard
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- HarmanKardon SUBTS7 pwr sm 维修 电路 原理图