HarmanKardon-HKTS30.WQ-htss-sm维修电路原理图.pdf

《HarmanKardon-HKTS30.WQ-htss-sm维修电路原理图.pdf》由会员分享，可在线阅读，更多相关《HarmanKardon-HKTS30.WQ-htss-sm维修电路原理图.pdf（49页珍藏版）》请在收音机爱好者资料库上搜索。

1、HKTS 20/230, HKTS 30/230 HKTS 30/WQ HKTS 60/230. Surround loudspeaker systems with active subwoofer. Earlier versions with HKTS 200 SUB. Later versions with HKTS 210 SUB. Released EU2011 Harman Consumer Group, Inc. Rev 3, 05/2012 8500 Balboa Boulevard Northridge, California 91329 CONTENTS HKTS 20+30

2、 USER GUIDE 2 HKTS 60 with 200 SUB USER GUIDE 13 HKTS 60 with 210 SUB USER GUIDE 24 HKTS 20 SAT EXPLODED VIEW/PARTS 36 HKTS 30 SAT EXPLODED VIEW/PARTS 37 HKTS 30WQ SAT EXPLODED VIEW 38 HKTS 20+30 CENTER EXPLODED VIEW 39 HKTS 20+30WQ CENTER EXPL VIEW 40 HKTS 60 SAT EXPLODED VIEW 41 HKTS 200 SUB EXPLO

3、DED VIEW/PARTS 42 HKTS 200 PARTS LIST 43 HKTS 200 SCHEMATIC DIAGRAM 44 HKTS 210 SUB EXPLODED VIEW/PARTS 45 HKTS 210 PARTS LIST 46 HKTS 210 SCHEMATIC DIAGRAMS 47 RadioFans.CN HKTS 20/HKTS 30 Designed to Entertain. User Guide English Home Theater Speaker System 0165CSK - HK HKTS20 and HKTS30 v6.indd 1

4、08/10/09 13:31:43 RadioFans.CN 23 ENGLISH Introduction Thank you for purchasing the Harman Kardon HKTS20/HKTS30 speaker system, with which youre about to begin many years of listening enjoyment. The HKTS20/HKTS30 has been custom designed to provide all the excitement and power of the cinema experien

5、ce in your own living room. While sophisticated electronics and state-of-the-art speaker components are hard at work within the HKTS20 and HKTS30, hookup and operation are simple. Color-keyed cables and connections, and simple controls make the HKTS20/HKTS30 easy to use. To obtain maximum enjoyment

6、from your new home theater speaker system, we urge you to take a few minutes to read through this manual. This will help ensure that the connections you make to your receiver (or preamp/processor), amplifier and other devices are correct. In addition, a few minutes spent learning the functions of th

7、e various controls will enable you to take advantage of all the power and refinement the HKTS20/HKTS30 is able to deliver. If you have any questions about this product, its installation or its operation, please contact your dealer, the best local source of information. Description and Features The H

8、KTS20/HKTS30 is a complete six-piece home theater speaker system that includes: An 8-inch, 200-watt powered subwoofer Four identical two-way video-shielded satellite speakers (the HKTS30 satellite speakers feature dual drivers) for the left and right front, and left and right rear (surround) speaker

9、 positions A dedicated, voice-matched, video-shielded, dual-driver center speaker Removable bases and wall-mount brackets for the satellite speakers and a wall- mount bracket for the center speaker All of the cables you need to connect all of the speakers to your receiver or preamp/ processor and am

10、plifier. The speaker cables all use a color-coding system to conform to the Consumer Electronics Association (CEA) standard. This color-coding system minimizes confusion when connecting the speakers, especially when you are connecting them to a Harman Kardon receiver. The HKTS200SUB subwoofer is equ

11、ipped with a special LFE input that simplifies connection to receivers and preamp/processors with dedicated subwoofer outputs that carry low-frequency signals. Other conveniences include a level control, a phase switch for fine-tuning bass response to suit your listening environment and taste, and a

12、n efficient switching system that senses the presence of an audio signal and automatically switches the subwoofer from standby mode to on. Wall-mount brackets are included for the satellite and center speakers, and shelf stands are included for the satellite speakers. Optional HKFS3 floorstands are

13、available separately from your Harman Kardon dealer. Harman Kardon invented the high-fidelity receiver fifty years ago. With state-of-the-art features and time-honored circuit designs, the HKTS20/ HKTS30 is a perfect complement to a Harman Kardon receiver, or any home theater system. Four satellite

14、speakers for front left/right and surround left/right (HKTS30 satellites shown) One powered subwoofer Four wall-mount brackets for satellite speakers One wall-mount bracket for center speaker Four metal stop plates and screws (for satellite speaker wall-mount brackets) One combination LFE and trigge

15、r cable for connection to the subwoofer (LFE cable has purple connectors) One 4-meter (13.1-foot) speaker cable for center speaker (green color bands) Two 5-meter (16.4-foot) speaker cables for front satellites (red and white color bands) Two 10-meter (32.8-foot) speaker cables for rear satellites (

16、gray and blue color bands) Harman Kardon HKTS 20 / HKTS 30 Included 0165CSK - HK HKTS20 and HKTS30 v6.indd 308/10/09 13:31:50 RadioFans.CN PL0004-01001 1 2 3 4 5 8 9 6 7 4 45 HKTS200SUB Rear-Panel Connections Subwoofer Level Control: .Use this control to adjust the HKTS200SUBs volume. Turn clockwise

17、 to increase the volume; turn counterclockwise to decrease the volume. Bass Boost Switch: 1.Set this switch to ON to enhance the HKTS200SUBs low-frequency performance. Set this switch to OFF for normal low-frequency performance. Phase Switch: 2.The Phase Switch 2 determines whether the HKTS200SUBs p

18、iston-like action moves in and out in phase with the satellite speakers. If the subwoofer were to play out of phase with the satellite speakers, the sound waves produced by the subwoofer could be canceled out, reducing bass performance and sonic impact. This phenomenon depends in part on the relativ

19、e placement of all the speakers in the room. In most cases the Phase Switch 2 should be left in the NORMAL position. However, it does no harm to experiment, and you can leave the Phase Switch 2 in the position that maximizes bass response and impact. Power On Mode Switch:3. When set in the AUTO posi

20、tion and when the Power Switch 7 is set to ON, the HKTS200SUB will automatically turn itself on when it receives an audio signal, and will enter the standby mode once no audio signal has been received for about 15 minutes. When this switch is set in the ON position, the HKTS200SUB will remain on whe

21、ther or not it is receiving an audio signal. An LED on the HKTS200SUBs top panel indicates whether the subwoofer is in the on or standby state: When the LED is illuminated white, the HKTS200SUB is turned on. When the LED is not illuminated, the HKTS200SUB is in standby mode. When the Master Power Sw

22、itch 7is set to OFF, the LED will not be illuminated, no matter what setting the Power On Mode Switch 3is in. External Trigger Input:4. Use the mini-plug of the supplied combination LFE and trigger cable to connect the External Trigger Input to the trigger output of another compatible component. Whe

23、never a trigger signal between 3 and 30V (AC or DC) is detected, the HKTS200SUBs amplifier will turn on. The HKTS200SUBs amplifier will turn off after the trigger signal ceases. (This will occur even when the Power On Mode Switch 3 is in the AUTO position.) Line-Level LFE In Connector:5. Use the LFE

24、 (purple) connector of the supplied combination LFE and trigger cable to connect the Line-Level LFE In to the dedicated subwoofer output of a receiver or preamp/processor. This input bypasses the HKTS200SUBs internal crossover circuitry, so it should only be used with a subwoofer output that has bee

25、n low-pass filtered. If your receiver or preamp/processor does not have a dedicated subwoofer output that is low-pass filtered you should use the HKTS200SUBs Line- Level L/R In Connectors 6 instead. Line-Level L/R In Connectors:6. Use these connectors if your receiver or preamp/processor does not ha

26、ve digital surround sound decoding or a subwoofer output that is low-pass filtered. If your receiver or preamp/processor has a separate subwoofer output, use the LFE (purple) connector of the supplied combination LFE and trigger cable to connect it to either one of the HKTS200SUBs Line-Level L/R In

27、Connectors. If your receiver or preamp/processor does not have a separate subwoofer output, use two Y-adapters (not supplied). Connect an adapters single end to the units preamp output for that channel. Connect one of the adapters dual ends to the main amp input for that channel, and connect the ada

28、pters other dual end to one of the HKTS200SUBs Line-Level L/R In Connectors. Repeat with the other Y-adapter, preamp channel, main amp input and HKTS200SUB Line-Level L/R In Connector. Power Switch: 7.Set this switch in the ON position to turn the HKTS200SUB on. The subwoofer will then either be on

29、or in standby mode, depending on the setting of the Power On Mode Switch 3. Power Cord (Non-Detachable):8. After you have made and verified all subwoofer and speaker connections described in this manual, plug this cord into an active, unswitched electrical outlet for proper operation of the HKTS200S

30、UB. DO NOT plug this cord into the accessory outlets found in some audio components. 0165CSK - HK HKTS20 and HKTS30 v6.indd 408/10/09 13:31:51 Harman KardonHKTS 20+30+60 Service Manual Page 4 of 49 5 ENGLISH Speaker Placement NOTE: The following speaker placement, mounting and connection instruction

31、s are identical for the HKTS20 and HKTS30 systems. Color-Coding System The HKTS20 and HKTS30 use the channel color-coding system established by the CEA to make setting up your home theater speaker system as easy as possible. The HKTS20/ HKTS30 systems include speaker wires with color bands on each e

32、nd. Speaker PositionWire Color Band Front LeftWhite Front RightRed CenterGreen Surround LeftBlue Surround RightGray SubwooferPurple Placing the Front Speakers The front speakers should be placed the same distance from each other as they are from the listening position. They should be placed at about

33、 the same height from the floor as the listeners ears will be. They also can be angled toward the listener. Left Front Speaker Right Front Speaker Placing the Center Speaker The center speaker should be placed slightly behind (farther away from the listener) the front left and right speakers. Its ce

34、nter should be no more than 2 feet (61cm) above or below the tweeters of the front left and right speakers. If you have a CRT television, it may be convenient to set the center speaker on top of the television set. Center Speaker Left Front Speaker Right Front Speaker 0 - 2 ft (0 - 61cm) Placing the

35、 Subwoofer Since our ears do not hear directional sound at the low frequencies where the subwoofer operates, it will have good performance from just about any location in your room. However, the best bass reproduction is likely to be heard when the subwoofer is placed in a corner along the same wall

36、 as the front left and right speakers. You can experiment with subwoofer placment by temporarily placing it in the listening position and playing music with strong bass content. Move around to various locations in the room while the system is playing and listen until you find the location where the

37、bass performance is best. Place the subwoofer in that location. Left Front Speaker Right Front Speaker Subwoofer Placing the Surround Speakers Left Surround Sound Right Surround Sound 5 - 6 ft (1.5m - 1.8m) Left Front Speaker Right Front Speaker Subwoofer Left Surround Sound Right Surround Sound The

38、 two surround speakers should be placed slightly behind the listening position, facing each other and, ideally, should be 56 feet (1.5m1.8m) from the floor. An alternate location would be on a wall behind the listening position, facing forward. The surround speakers should not call attention to them

39、selves while theyre playing. Experiment with their placement until you hear a diffuse, ambient sound accompanying the program material heard from the front left and right and center speakers. Mounting Options for Satellite and Center Speakers Shelf Placement You can place the satellite and center sp

40、eakers on shelves. The satellite speakers have built-in bases for shelf placement. You can also remove the bases if desired. To remove a satellite speakers base, pull it straight off the speaker, as shown in the illustration. Applying even pressure to both sides of the base will allow it to slide of

41、f smoothly. Wall-Mounting: Satellite Speakers IMPORTANT: Read the Speaker Connections section, on page 7, before wall-mounting the satellite speakers. You will need to insert the speaker wires through the wall mounts and connect the wires to the speakers during the process of installing the wall-mou

42、nts. NOTE: If you are using your own speaker wire, it must be no thicker than the wire supplied with the speakers. Thicker wire will prevent the wall-mount bracket from sliding onto the speaker. Decide on the location for the speaker 1. (see Speaker Placement, opposite). Remove the speakers base as

43、explained in 2. Shelf Placement, above. Disassemble the wall-mount bracket by sliding the two sections apart, as shown in the 3. illustration. Attach the wall portion of the wall-mount onto the wall using hardware that is 4. appropriate for the walls construction and materials. We recommend first an

44、choring the mount using its keyhole, then attaching it with another anchor through its top opening, as shown in the illustration. Note that the satellite speakers weigh 3.3 lb (1.5kg). Be sure to use hardware that can support this weight. Top Opening Keyhole Opening Bottom Opening Apply Pressure Eve

45、nly to Both Sides of Base Lift Base Straight off Speaker Pull Sections Apart Center Speaker Harman KardonHKTS 20+30+60 Service Manual Page 5 of 49 6 67 NOTE: If youre running the speaker wire through the wall you can bring it out directly behind the bracket location and insert it through the bottom

46、opening in the wall portion of the wall-mount, as shown in the illustration. This will keep the wire completely hidden from view once the installation is complete. Insert Wire into Bottom Opening Bring Wire Out through Here If youre not running the speaker wire through the wall, insert it through th

47、e wall portion 5. of the wall-mount bracket as shown in the illustration. Pass the speaker wire through the speaker portion of the wall-mount as shown in the 6. illustration. Bring Wire In through Here Bring Wire Out through Here If you have not already removed the speakers base, do so by pulling it

48、 straight off the 7. speaker, as shown in the illustration. Applying even pressure to both sides of the base will allow it to slide off smoothly. Apply Pressure Evenly to Both Sides of Base Lift Base Straight off Speaker CAUTION: Before making speaker connections, be sure that your receiver or ampli

49、fier is turned OFF and preferably, its AC cord is unplugged from the AC outlet. Connect the speaker wire to the speaker terminals as shown in the illustration: 8. Press down on the top of the terminal to open the connection hole.a) Insert the wires bare end all the way into the hole.b) Release the terminal to secure the wire. c) Insert the conductor with the colored band into the speakers red ( + ) terminal, and insert the other conductor into the speakers black ( )