《HarmanKardon-HKTS10-htss-sm维修电路原理图.pdf》由会员分享,可在线阅读,更多相关《HarmanKardon-HKTS10-htss-sm维修电路原理图.pdf(23页珍藏版)》请在收音机爱好者资料库上搜索。
1、harman/kardon HKTS 10 Home Cinema Speaker System SERVICE MANUAL harman/kardon, Inc. 250 Crossways Park Dr. Woodbury, New York 11797Rev0 8/2002 RadioFans.CN CONTENTS SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 DETAIL
2、ED SPECIFICATIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 CONTROLS or whether it has moved: i.e., the speaker that was not work- ing still has no sound and the speaker that was working is still fine. If the problem is in the same place, the source of the
3、problem is most likely with your receiver or amplifier, and you should consult the owners manual for that product for further information. If the problem has followed the speaker, consult your dealer for further assistance or, if that is not possible, visit our Web site at for further information. I
4、f there is no sound from the center speaker: Check all wires and connections between receiver/amplifier and speaker. Make sure all wires are connected. Make sure none of the speaker wires are frayed, cut or punctured. If your receiver/processor is set in Dolby Pro Logic mode, make sure the center sp
5、eaker is not in phantom mode. If your receiver/processor is set in Dolby Digital or DTS mode, make sure the receiver/processor is configured so that the center speaker is enabled. If the system plays at low volumes but shuts off as volume is increased: Check all wires and connections between receive
6、r/amplifier and speakers. Make sure all wires are connected. Make sure none of the speaker wires are frayed, cut or punctured. If more than one pair of main speakers is being used, check the minimum impedance requirements of your receiver/amplifier. If there is low (or no) bass output: Make sure the
7、 SUB or line-level inputs of the SUB-TS10 subwoofer and SUB or LFE output of your receiver or amplifier are properly connected by the RCA-type patch cord. If you are using the SUB-TS10s speaker- level inputs, check your speaker cables to make sure they are all connected; that none of the wires are f
8、rayed, cut or punctured; and that you have maintained the correct polarity by connecting positive terminals to positive terminals, and negative terminals to negative terminals. Make sure the subwoofer is plugged into an active electrical outlet and its Master Power Switch is switched on to the “” po
9、sition. Check the speaker setup (bass manage- ment) settings in your AVR receiver or processor to make certain that the front, center and surround speakers are config- ured for “Small,” and that the subwoofer is set for “Yes” or “On.” If there is no sound from the sur- round speakers: Check all wire
10、s and connections between receiver/amplifier and speakers. Make sure all wires are connected. Make sure none of the speaker wires are frayed, cut or punctured. Review proper operation of your receiver/processor and its surround sound features. Make sure the movie or TV show you are watching is recor
11、ded in a surround sound mode. If it is not, check to see whether your receiver/processor has other surround modes you may use. In Dolby Digital or DTS mode, make sure your receiver/processor is configured so that the surround speakers are enabled. Review the operation of your DVD player and the jack
12、et of your DVD to make sure that the DVD features the desired Dolby Digital or DTS mode, and that you have properly selected that mode using both the DVD players menu and the DVD discs menu. TROUBLESHOOTINGTROUBLESHOOTING HKTS 10 harman/kardon RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION RISK OF ELECT
13、RIC SHOCK DO NOT OPEN CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN harman/kardon SUB-TS10 For use with HKTS 10 System OFF NORMALREVERSE OOFER LEVEL ONAUTO IMPORTANT: CONNECT STRIPED WIRE TO RED ( ) SPEAKER TERMINAL. AC 120V60Hz POWER Made in China L R SUB PHASE FILTER CONTROL SUBW GREEN: ON RED: STAND
14、-BY FILTER REMOTE LINE LEVEL IN ON LR AC VOLT METER (10V) SIGNAL GENERATOR AMPLIFIER Equipment needed: Function/signal generator/sweep generator Integrated Amplifier Multimeter Speaker cables General Unit Function (UUT = Unit Under Test) 1) From the signal generator, connect one line level (RCA) cab
15、le to the single Sub input on the UUT. 2) On the front of the unit, turn the LEVEL control full counterclockwise. FILTER control should be OFF. 3) Turn on generator, adjust to 75mV, 50 Hz. 4) Plug in UUT; turn the power switch ON. LED should be Red. Turn LEVEL control full clockwise (MAX) 5) LED sho
16、uld now be Green; immediate bass response should be heard and felt from port tube opening. 6) Turn off generator, turn VOLUME control fully counterclockwise, disconnect RCA cable. 7) Connect one pair of speaker cables to Speaker Level input terminal (IN) on Right channel only. Cables should be conne
17、cted to an integrated amplifier fed by the signal generator. 8) Turn on generator and adjust so that speaker level input at the amplifier is 1.6V, 50 Hz. Turn LEVEL control full clockwise. 9) Green LED should light, immediate bass response should be heard and felt from the port tube opening. Sweep F
18、unction 1) Follow steps 7-9 above, using a sweep generator as a signal source. 2) Sweep generator from 20Hz to 300Hz. Listen to the cabinet and drivers for any rattles, clicks, buzzes or any other noises. If any unusual noises are heard, remove woofers and test. Driver Function 1) Remove woofer from
19、 cabinet; detach + and - wire clips. 2) Check DC resistance of woofer; it should be 3.5 ohms 10% 3) Connect a pair of speaker cables to driver terminals. Cables should be connected to an integrated amplifier fed by a signal generator. Turn on generator and adjust so that speaker level output is 5.0V
20、. 4) Sweep generator from 20Hz to 1kHz. Listen to driver for any rubbing, buzzing, or other unusual noises. Test Set Up and Procedure HKTS 10 HKTS10 UNDER TEST 10 HKTS 10harman/kardon 11 Part NumberDescription Subwoofer SUB TS10 30PF14FM-DW0212 Woofer (DCR = 3.5 ohms +/-10%) xc125006-bFront Baffle x
21、c125007Grille wi5334-1Foot (4) 06-T5305004Screw for front baffle & Feet (8) Satellites SAT-TS10 10PR70BZK-HW02 4 woofer 35DM13NG-PT0213 mm tweeter XR5176-1Crossover Network xc045016-bBaffle xc045017-1Grille xd045016-bEnclosure Center Channel CEN-TS10 10PR70BZK-MW02Woofer 4 35DM13NG-HT0213mm tweeter
22、xr5177-1Crossover Network xc045014-bBaffle xd045014-bEnclosure xc045015-1Grille Packing/Accessories wg5320Master carton ai5170 Owners manual at5108Warranty card sal5009Wire set 40 (surround) sal063-1Wire set 20 (center) sal5020Wire set 15 (front satellites) sal504415 RCA cable wi5688Center Channel B
23、racket/Support wi5689Foot wi5691Wall Bracket for Satellite HKTS 10 Subwoofer/Satellite/Center Mechanical/Packing Parts List HKTS 10harman/kardon 12 HKTS 10 harman/kardon HKTS 10harman/kardon 13 HKTS 10harman/kardon 14 HKTS 10harman/kardon 15 16 Integrated Circuit Diagrams C B E TIP31C NPN, TIP32C PN
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- HarmanKardon HKTS10 htss sm 维修 电路 原理图