《HarmanKardon-HKTS6-htss-sm维修电路原理图.pdf》由会员分享,可在线阅读,更多相关《HarmanKardon-HKTS6-htss-sm维修电路原理图.pdf(22页珍藏版)》请在收音机爱好者资料库上搜索。
1、harman/kardon HKTS 5/HKTS 6 Home Theater Speaker System SERVICE MANUAL harman/kardon, Inc. 250 Crossways Park Dr. Woodbury, New York 11797 Rev2 1/2004 RadioFans.CN HKTS5/HKTS6harman/kardon - CONTENTS - BASIC SPECIFICATIONS.1 DETAILED SPECIFICATIONS.2 CONNECTIONS.3 OPERATION.4 TROUBLESHOOTING.5 SUB-T
2、S5/TS6 EXPLODED VIEW.6 SUB-TS5/TS6 AMPLIFIER EXPLODED VIEW. .7 SUB-TS5/TS6 TEST PROCEDURE. .8 HKTS 5/HKTS 6 MECHANICAL/SATELLITE PARTS LIST.9 HKTS 5/HKTS 6 PACKAGE.10 SUB-TS5/ TS6 BLOCK DIAGRAM. 11 SUB- TS5/ TS6 PCB DRAWINGS.12 SUB- TS5/ TS6 ELECTRICAL PARTS LIST .15 SUB- TS5/ TS6 IC/TRANSISTOR PINO
3、UTS.18 SUB- TS5/ TS6 SCHEMATICS.19 HKTS 5/HKTS6 System Frequency Response 35Hz 20kHz (6dB) Satellites Recommended Power 10 70 watts Impedance 8 ohms nominal Sensitivity 86dB 1 watt/1 meter Tweeter One 1/2 dome, video-shielded Midrange One 3 driver, video-shielded Dimensions (H x W x D) 4-5/8 x 3-1/8
4、 x 3-3/4 (117mm x 79mm x 93mm) Weight 1.1 lb/0.5kg Center Recommended Power 10 70 watts Impedance 8 ohms nominal Sensitivity 86dB 1 watt/1 meter Tweeter One 1/2 dome, video- shielded Midrange Dual 3 drivers, video- shielded Dimensions (H x W x D) 3-1/2 x 7-5/8 x 3-3/4 (89mm x 194mm x 93mm) Weight 1.
5、89 lb/0.86kg Subwoofer SUB-TS5/TS6 Amplifier 100 watts RMS Woofer 10 woofer, bass-reflex enclosure Dimensions (H x W x D) 15-3/4 x 15-3/4 x 16-3/4 (400mm x 400mm x 425mm) Weight 33.5 lb/15.2kg Occasional refinements may be made to existing products without notice but will always meet or exceed origi
6、nal specifications unless otherwise stated RadioFans.CN 1 SUB-TS5/TS6 Amplifier100w Powered Subwoofer Amplifier LINE VOLTAGEYes/NoHi/Lo LineUnitNotes US 120vac/60HzYes108-132VrmsNormal Operation ParameterSpecificationUnitQA Test LimitsConditionsNotes Amp Section Type (Class AB, D, other)AB ABn/aExte
7、rnal Sink required for Class AB Load Impedance (speaker)4 Ohmsn/aNominalZ-curve required Rated Output Power100 Watts951 input driven THD Rated Power0.08 %0.322k filter THD 1 Watt0.1 %0.522k filter DC Offset10 mV-DC20 Speaker Outputs Damping factor100 DF50Measured at speaker terminals, Output power 9
8、0 Watts THD 0.1 % Input Sensitivity Input Frequency50 Hz50Nominal Freq.1 input driven SUB Input135 mVrms2dBTo Rated PowerSUB input driven only Signal to Noise SNR-A-Weighted100 dBA90rel. to rated powerA-Weighting filter SNR-unweighted80 dBr75rel. to rated power22k filter SNR 1W-unweighted60 dBr55rel
9、. to 1W Output22k filter Residual Noise Floor1.5 mVrms2.5Volume max, using RMS reading DMM/VOM (or A/P) Residual Noise Floor1mVrms(max)2Volume max, w/ A/P Swept Bandpass Measurement (Line freq.+ harmonics) Input Impedance SUB Line input 15 K ohmsn/aNominal Filters Low Pass (fixed or variable)fixed-2
10、dB Slope or whether it has moved: i.e., the speaker that was not work- ing still has no sound and the speaker that was working is still fine. If the problem is in the same place, the source of the problem is most likely with your receiver or amplifier, and you should consult the owners manual for th
11、at product for further information. If the problem has followed the speaker, consult your dealer for further assistance or, if that is not possible, visit our Web site at for further information. If there is no sound from the center speaker: Check all wires and connections between receiver/amplifier
12、 and speaker. Make sure all wires are connected. Make sure none of the speaker wires are frayed, cut or punctured. If your receiver/processor is set in Dolby Pro Logic* mode, make sure the center speaker is not in phantom mode. If your receiver/processor is set in Dolby Digital or DTS mode, make sur
13、e the receiver/processor is configured so that the center speaker is enabled. If the system plays at low volumes but shuts off as volume is increased: Check all wires and connections between receiver/amplifier and speakers. Make sure all wires are connected. Make sure none of the speaker wires are f
14、rayed, cut or punctured. If more than one pair of main speakers is being used, check the minimum impedance requirements of your receiver/amplifier. If there is low (or no) bass output: Make sure the SUB input of the SUB-TS5/6 subwoofer and SUB or LFE output of your receiver or amplifier are properly
15、 connected by the RCA-type patch cord. Make sure the connections to the Speaker Inputs have the correct polarity (+ and ). Make sure the subwoofer is plugged into an active electrical outlet and its Power switch is switched on to the “” position. Check the speaker setup (bass manage- ment) settings
16、in your AVR receiver or processor to make certain that the front, center and surround speakers are config- ured for “Small,” and that the subwoofer is set for “Yes” or “On.” If there is no sound from the sur- round speakers: Check all wires and connections between receiver/amplifier and speakers. Ma
17、ke sure all wires are connected. Make sure none of the speaker wires are frayed, cut or punctured. Review proper operation of your receiver/processor and its surround sound features. Make sure the movie or TV show you are watching is recorded in a surround sound mode. If it is not, check to see whet
18、her your receiver/processor has other surround modes you may use. In Dolby Digital or DTS mode, make sure your receiver/processor is configured so that the surround speakers are enabled. Review the operation of your DVD player and the jacket of your DVD to make sure that the DVD features the desired
19、 Dolby Digital or DTS mode, and that you have properly selected that mode using both the DVD players menu and the DVD discs menu. TROUBLESHOOTINGTROUBLESHOOTING HKTS5harman/kardon HKTS5harman/kardon HKTS5/HKTS6harman/kardon HKTS5/HKTS6 harman/kardon Ref.Part NumberDescriptionQty #1Not For SaleHKTS5/
20、HKTS6 Enclosure1 #2(HKTS5) sz5321HK Logo1 (HKTS6) sz5930HK Logo1 #325MF10DZB-DW0210 woofer (DCR = 3.4 ohms ?10%)1 #406-t4205012Amplifier/woofer screw t4*2015 #5wi5448Foot (bumper)4 #606-t5345005Foot screw4 #7wi5447Rubber foot4 #8wi5600Port Tube1 #9Not For SaleHKTS5/HKTS6 Amplifier Assembly1 HKTS5/HK
21、TS6harman/kardon 6 7 HKTS5/HKTS6harman/kardon HKTS 5/HKTS 6 TEST PROCEDURE Equipment needed: Function/signal generator/sweep generator Integrated Amplifier Multimeter Speaker cables Single RCA cable General Unit Function (UUT = Unit Under Test) 1) From the signal generator, connect one line level (R
22、CA) cable to the single SUB input. 2) On the front of the unit, turn the LEVEL control full counterclockwise. 3) Turn on generator, adjust to 150mV, 50 Hz. 4) Plug in UUT; turn the power switch ON. LED should be Red. Turn LEVEL control full clockwise (MAX) 5) LED should now be Green; immediate bass
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- HarmanKardon HKTS6 htss sm 维修 电路 原理图