《HarmanKardon-AVR430-avr-sm维修电路图 手册.pdf》由会员分享,可在线阅读,更多相关《HarmanKardon-AVR430-avr-sm维修电路图 手册.pdf(126页珍藏版)》请在收音机爱好者资料库上搜索。
1、 harman/kardon AVR430 AVR430 7 X 65W 7.1 CHANNEL A/V RECEIVER AVR630 AVR630 7 X 75W 7.1 CHANNEL A/V RECEIVER SERVICE MANUAL CONTENTS ESD WARNING.2 LEAKAGE TESTING.3 AVR430 BASIC SPECIFICATIONS.4 AVR630 BASIC SPECIFICATIONS.5 FRONT PANEL CONTROLS.6 REAR PANEL CONNECTIONS.9 REMOTE CONTROL FUNCTIONS.12
2、 TROUBLESHOOTING GUIDE.16 PROCESSOR RESET16 SERVICE PROCEDURE.17 BULLETIN HK2004-04.20 TECH TIP HKTT2004-03.23 TECH TIP HKTT2003-01.27 BLOCK DIAGRAM.28 EXPLODED VIEW.29 EXPLODED VIEW PARTS LIST.30 AVR630 MECHANICAL PARTS LIST.32 AVR630 ELECTRICAL PARTS LIST.34 AVR430 MECHANICAL PARTS LIST.54 AVR430
3、ELECTRICAL PARTS LIST.56 SEMICONDUCTOR PINOUTS.75 PCB DRAWINGS.103 SCHEMATICS.114 WIRING DIAGRAM.125 PACKING.126 harman/kardon, Inc. 250 Crossways Park Dr. Woodbury, New York 11797 Rev2 10/2005 www.freeservicemanuals.infoIts Free www.freeservicemanuals.info RadioFans.CN Eachprecautioninthismanualsho
4、uldbefollowedduringservicing. Components identified with the IEC symbolin the parts list are special significance to safety. When replacing a component identified with , use only the replacement parts designated, or parts with the same ratings or resistance, wattage, or voltage that are designated i
5、n the parts list in this manual. Leakage-current or resistance measurements must be made to determine that exposed parts are acceptably insulated from the supply circuit before retuming the product to the customer. Some semiconductor (solid state) devices can be damaged easily by static electricity.
6、 Such components commonly are called Electrostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field effect transistors and semiconductor chip components. The following techniques should be used to help reduce the incidence of component damage caused b
7、y static electricity. 1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any electrostatic charge on your body by touching a known earth ground. Alternatively, obtain and wear a commercially available discharging wrist strap device, which should
8、be removed for potential shock reasons prior to applying power to the unit under test. 2. After removing an electrical assembly equipped with ES devices, place the assembly on a conductive surface such as aluminum foil, to prevent electrostatic charge build-up or exposure of the assembly. 3. Use onl
9、y a grounded-tip soldering iron to solder or unsolder ES devices. 4. Use only an anti-static solder removal device. Some solder removal devices not classified as anti-static can generate electrical charges sufficient to damage ES devices. 5. Do not use freon-propelled chemicals. These can generate e
10、lectrical change sufficient to damage ES devices. 6. Do not remove a replacement ES device from its protective package until immediately before you are ready to install it. (Most replacement ES devices are packaged with leads electrically shorted together by conductive foam, aluminum foil or compara
11、ble conductive material.) 7. Immediately before removing the protective material from the leads of a replacement ES device, touch the protective material to the chassis or circuit assembly into which the device will be installed. Be sure no power is applied to the chassis or circuit, and observe all
12、 other safety precautions. 8. Minimize bodily motions when handling unpackaged replacement ES devices. (Otherwise harmless motion such as the brushing together or your clothes fabric or the lifting of your foot from a carpeted floor can generate static electricity sufficient to damage an ES devices.
13、 CAUTION : AVR430/AVR630AVR430/AVR630 harman/kardon www.freeservicemanuals.infoIts Free www.freeservicemanuals.info RadioFans.CN 2 1. Inspect all lead dress to make certain that leads are not pinched or that hardware is not lodged between the chassis and other metal partsintheunit. 2. Be sure that a
14、ny protective devices such as nonmetallic control knobs, insulating fish- papers,cabinetbacks,adjustmentand compartment covers or shields, isolation resistor-capacitynetworks,mechanical insulators, etc. Which were removed for the servicingareproperlyre-installed. Before returning the unit to the use
15、r, perform the following safety checks : 3. Be sure that no shock hazard exists ; check for leakage currentusingSimpsonModel229LeakageTester,standard equipment item No. 21641, RCA Model WT540A or use alternate method asfollows : Plug the power cord directly Into a 120 volt AC receptacle (do not use
16、an Isolation Transformer for this test). Using two clip leads, connect a 1500ohms,10wattResistorparalleledbya0.15uFcapacitor,inserieswithallexposedmetalcabinetpartsandaknownearthground,such as a water pipe or conduit. Use a VTVM or VOM with 1000 ohms per volt, or higher sensitivity to measure the AC
17、 voltage drop across the resistor. (See diagram) Move the resistor connection to each exposed metal part having a return path to the chassis (antenna, metal, cabinet,screwheads,knobsandcontrolshafts,escutcheon,etc.)andmeasuretheACvoltagedropacrosstheresistor.(Thistestshouldbe performedwiththe0.35vol
18、tRMSormoreisexcessiveandindicatesapotentialshockhazardwhichmustbecorrectedbeforereturningthe unittotheowner. AVR430/AVR630AVR430/AVR630 harman/kardon www.freeservicemanuals.infoIts Free www.freeservicemanuals.info RadioFans.CN 3 AVR 430 TECHNICAL SPECIFICATIONS Audio Section Stereo Mode Continuous A
19、verage Power (FTC) 80 Watts per channel, 20Hz20kHz, 0.07% THD, both channels driven into 8 ohms Seven-Channel Surround Modes Power per Individual Channel Front L&R channels: 65 Watts per channel 0.07% THD, 20Hz20kHz into 8 ohms Center channel: 65 Watts 0.07% THD, 20Hz20kHz into 8 ohms Surround (L &
20、R Side, L & R back) channels: 65 Watts per channel 0.07% THD, 20Hz20kHz into 8 ohms Input Sensitivity/Impedance Linear (High-Level)200mV/47k ohms Signal-to-Noise Ratio (IHF-A)95dB Surround System Adjacent Channel Separation Pro Logic I/II 40dB Dolby Digital (AC-3)55dB DTS55dB Frequency Response 1W (
21、+0dB, 3dB)10Hz 130kHz High Instantaneous Current Capability (HCC)40 Amps Transient Intermodulation Distortion (TIM)Unmeasurable Slew Rate40V/sec FM Tuner Section Frequency Range87.5108.0MHz Usable SensitivityIHF 1.3V/13.2dBf Signal-to-Noise RatioMono/Stereo 70/68dB DistortionMono/Stereo 0.2/0.3% Ste
22、reo Separation40dB 1kHz Selectivity400kHz, 70dB Image Rejection80dB IF Rejection90dB AM Tuner Section Frequency Range5201720kHz Signal-to-Noise Ratio45dB Usable SensitivityLoop 500V Distortion1kHz, 50% Mod 0.8% Selectivity10kHz, 30dB Video Section Television FormatNTSC Input Level/Impedance1Vp-p/75
23、ohms Output Level/Impedance1Vp-p/75 ohms Video Frequency Response (Composite and S-Video)10Hz8MHz (3dB) Video Frequency Response (Component Video) 10Hz50MHz (3dB) General Power RequirementAC 120V/60Hz Power Consumption59W idle, 940W at rated power output (7 channels driven) DimensionsProductShipping
24、 Width17.3 inches (440mm)20.1 inches (510mm) Height6.5 inches (165mm)10 inches (254mm) Depth17.1 inches (435mm)22.2 inches (565mm) Weight39 lb (17.7kg)45 lb (20.4kg) Depth measurement includes knobs, buttons and terminal connections. Height measurement includes feet and chassis. All features and spe
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- HarmanKardon-AVR430-avr-sm维修电路图 手册 HarmanKardon AVR430 avr sm 维修 电路图