HarmanKardon-AVR160.230-avr-sm维修电路图 手册.pdf

《HarmanKardon-AVR160.230-avr-sm维修电路图 手册.pdf》由会员分享，可在线阅读，更多相关《HarmanKardon-AVR160.230-avr-sm维修电路图 手册.pdf（116页珍藏版）》请在收音机爱好者资料库上搜索。

1、 harman/kardon Service Manual AVR 160/230 5 x 40W 5.1 CHANNEL A/V RECEIVER CONTENTS EXPLODED VIEW AND PARTS 12 ELECTRICAL PARTS LIST 13 SEMICONDUCTOR PINOUTS 41 PCB DRAWINGS 97 BLOCK DIAGRAM 104 WIRING DIAGRAM 105 AMP BIAS ADJUSTMENT 106 SCHEMATIC DIAGRAMS 107-116 ESD WARNING 2 FRONT AND REAR PANELS

2、 3 REMOTE CONTROL 5 TROUBLESHOOTING GUIDE 8 PROCESSOR RESET 8 TECHNICAL SPECIFICATIONS 9 PACKAGE LISTS AND PARTS 10 DISASSEMBLY 11 Released EU2010 Harman Consumer Group, Inc. Rev 0, 05/2010 8500 Balboa Boulevard Northridge, California 91329 harman/kardonAVR 160/230 Service Manual 1 of 116 RadioFans.

3、CN Eachprecautioninthismanualshouldbefollowedduringservicing. Components identified with the IEC symbolin the parts list are special significance to safety. When replacing a component identified with , use only the replacement parts designated, or parts with the same ratings or resistance, wattage,

4、or voltage that are designated in the parts list in this manual. Leakage-current or resistance measurements must be made to determine that exposed parts are acceptably insulated from the supply circuit before retuming the product to the customer. Some semiconductor (solid state) devices can be damag

5、ed easily by static electricity. Such components commonly are called Electrostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field effect transistors and semiconductor chip components. The following techniques should be used to help reduce the incide

6、nce of component damage caused by static electricity. 1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any electrostatic charge on your body by touching a known earth ground. Alternatively, obtain and wear a commercially available discharging w

7、rist strap device, which should be removed for potential shock reasons prior to applying power to the unit under test. 2. After removing an electrical assembly equipped with ES devices, place the assembly on a conductive surface such as aluminum foil, to prevent electrostatic charge build-up or expo

8、sure of the assembly. 3. Use only a grounded-tip soldering iron to solder or unsolder ES devices. 4. Use only an anti-static solder removal device. Some solder removal devices not classified as anti-static can generate electrical charges sufficient to damage ES devices. 5. Do not use freon-propelled

9、 chemicals. These can generate electrical change sufficient to damage ES devices. 6. Do not remove a replacement ES device from its protective package until immediately before you are ready to install it. (Most replacement ES devices are packaged with leads electrically shorted together by conductiv

10、e foam, aluminum foil or comparable conductive material.) 7. Immediately before removing the protective material from the leads of a replacement ES device, touch the protective material to the chassis or circuit assembly into which the device will be installed. Be sure no power is applied to the cha

11、ssis or circuit, and observe all other safety precautions. 8. Minimize bodily motions when handling unpackaged replacement ES devices. (Otherwise harmless motion such as the brushing together or your clothes fabric or the lifting of your foot from a carpeted floor can generate static electricity suf

12、ficient to damage an ES devices. CAUTION : harman/kardonAVR 160/230 Service Manual 2 of 116 RadioFans.CN 7 L - Audio - R RDSChannelDigitalSetTuningSurr. ModeKLSurr. Select Optical 3Coaxial 3Video Video 3 KLSourceKLMN 160 DSeSur e ENGLISH FRONT-PANEL CONTROLS Power indicatorTuning Mode Standby/On Swi

13、tch Channel Level Control Surround Modes USB Port Headphone EzSet/EQ Microphone Input Digital Audio Inputs (Optical 3 and Coaxial 3) Video 3 Analog Audio and Video Inputs TuningDigital Input M N Navigation Remote IR SensorSetMessage DisplaySurround SelectSource SelectorsVolume Power Indicator: This

14、LED has three possible modes: Main Power Off : When the AVR is unplugged or the Main Power Switch is off, this LED is off. Standby : Amber indicates that the AVR is ready to be turned on. On : When the AVR is turned on, this LED turns white. NOTE: If the PROTECT message ever appears, turn off the AV

15、R and unplug it. Check all speaker wires for a possible short. If none is found, bring the unit to an authorized Harman Kardon service center for inspection and repair before using it again. Standby/On Switch: This electrical switch turns the receiver on, or places it in Standby mode for quick turn-

16、on. RDS: Activates RDS functions for FM Radio Channel Level Control: Press this button to adjust the output level for any amplifier channel. It may be necessary to raise or lower the level of a specific channel to compensate for the placement of the relevant speaker in the room in relation to the li

17、stening position; e.g., the center channel speaker is further away from the listening position than the front left and right speakers, so that the dialogue is too soft to hear clearly. To adjust the level of a channel, press this button once. If the desired channel is not displayed on screen and in

18、the front-panel Message Display, use the Tuning Buttons to scroll to it. When the desired channel appears, use the M N Navigation Buttons to change the level. It is recommended that you avoid changing the channel levels after you have run the EzSet/EQ setup procedure described in the Initial Setup s

19、ection, which properly adjusts all channel levels. See the Advanced Functions section for more information on manual speaker setup, including level adjustment. Remote IR Sensor: This sensor receives infrared (IR) commands from the remote control. It is important to ensure that it is not blocked. If

20、covering the sensor is unavoidable, use an optional Harman Kardon HE 1000, or other infrared receiver, connecting it to the Remote IR Input on the AVR 160s rear panel. Digital Input: To change the audio input for the current source to one of the six digital audio inputs or the analog input for the s

21、ource, press this button and use the M N Navigation Buttons to change the input. Although any digital audio input may be assigned to any source, the analog audio inputs are all permanently dedicated to the source with which they are labeled. M N Navigation: These buttons are used to navigate the AVR

22、s menus. Set: Press this button to select the currently highlighted item. Message Display: Various messages appear in this two-line display in response to commands and changes in the incoming signal. In normal operation, the current source name appears on the upper line, while the surround mode is d

23、isplayed on the lower line. When the on-screen display menu system (OSD) is in use, the current menu settings appear. Tuning: Press these buttons to tune a radio station. harman/kardonAVR 160/230 Service Manual 3 of 116 RadioFans.CN 9 ENGLISH Component Video Monitor Output Component 1 use an analog

24、video connection instead. Always make a separate audio connection. REAR-PANEL CONNECTIONS harman/kardonAVR 160/230 Service Manual 4 of 116 RadioFans.CN 11 ENGLISH REMOTE CONTROL FUNCTIONS IR Transmitter Lens Device Power On Program Indicator AVR Selector AM/FM Test Tone Sleep Channel Controls On-Scr

25、een Display Channel Level Digital Input Tuning Mode Direct Station Entry Tuning Tone Mode Night Mode Track Skip Transport Controls Mute Device Power Off Source Selectors 6-/8-Channel Input Selector Volume TV/Video Speaker Setup KLM N Navigation OK Delay Alphanumeric Keys Memory Clear Preset Stations

26、 Selectors RDS Button Macros Dim The AVR 160 remote is capable of controlling up to 11 devices, including the AVR itself and a device connected to the Auxiliary Input. During the installation process, you may program the codes for each of your source components into the remote. Each time you wish to

27、 operate any component or the AVR, first press its Selector Button to change the device mode to the appropriate codes. Each Source Selector has been preprogrammed to control certain types of components, with only the codes specific to each brand and model changing, depending on which product code is

28、 programmed. The device types programmed into each selector, except the HDMI selectors, may not be changed. DVD: Controls Harman Kardon Blu-ray Disc players, and many brands of DVD players and recorders. CD: Controls CD players and recorders. Tape: Controls cassette decks. Video 1: Controls VCRs, Ti

29、Vo devices and DVRs, and the Harman Kardon DMC 1000 digital media center. Video 2: Controls cable and satellite television set-top boxes. Video 3: Controls televisions and other video displays. HDMI 1: Controls Harman Kardon Blu-ray Disc players, and many brands of DVD players and recorders. harman/

30、kardonAVR 160/230 Service Manual 5 of 116 RadioFans.CN 12 REMOTE CONTROL FUNCTIONS HDMI 2 and 3: Each code set controls a source device (VCR/PVR, DVD player or cable/satellite set-top box) connected to one of these inputs. AUX: Controls a device connected to the Auxiliary Input. Any given button may

31、 have different functions, depending on which component is being controlled. Some buttons are labeled with these functions. For example, the Sleep Button is labeled for use as the Channel Up Button when controlling a television or cable box. See Table A10 in the appendix for listings of the differen

32、t functions for each type of component. IR Transmitter Lens: As buttons are pressed on the remote, infrared codes are emitted through this lens. Power On Button: Press this button to turn on the AVR or another device. The Main Power Switch must first have been switched on. Mute Button: Press to mute

33、 the AVR 160s speaker and headphone outputs. To end the muting, press this button, adjust the volume, or turn off the receiver. Program Indicator: This LED lights up or flashes in one of three colors as the remote is programmed with codes. Power Off Button: Press to turn off the AVR 160 or another d

34、evice. AVR Selector: Press to switch the remote to AVR device mode. Source Selectors: Press one of these buttons to select a source device, e.g., DVD, CD, cable TV, satellite or HDTV tuner. This will also turn on the receiver and switch the remotes device mode to operate the source. AM/FM Button: Pr

35、ess this button to select the tuner as the source, or to switch between the AM and FM bands. 6-/8-Channel Input Selector: Press this button to select the 6-/8-Channel Inputs as the audio source. If a signal is present at the component video inputs assigned to this source, it will be used. If not, th

36、e receiver will use the video input and remote control codes for the last- selected analog video source. Test Tone: Press this button to activate the test tone for manual output- level calibration. TV/Video: This button has no effect on the receiver, but is used to switch video inputs on some video

37、source components. Sleep Button: Press this button to activate the sleep timer, which turns off the receiver after a programmed period of time of up to 90 minutes. Channel Controls: These buttons have no effect on the receiver, but are used to change channels on TVs and some video sources. Volume Co

38、ntrol: Press to raise or lower the volume, which will be shown in decibels (dB) in the Message Display. On-Screen Display (OSD): Press this button to activate the on-screen menu system. Channel Level: Press this button to adjust the output levels for any channel so that all speakers sound equally lo

39、ud at the listening position. Speaker Setup: Press this button to configure speaker sizes, that is, the low-frequency capability of each speaker. Navigation (KLM N) and OK Buttons: These buttons are used to make selections within the on-screen menu system, or when accessing the functions of the four

40、 buttons surrounding this area of the remote Channel Level, Speaker Setup, Digital Input or Delay. Digital Input Select: Press this button to select the specific digital audio input (or analog audio input) to which the current source is connected. Delay: Press this button to set delay times that com

41、pensate for placing the speakers at different distances from the listening position, or to resolve a “lip sync” issue that may be caused by digital video processing. NOTE: The Channel Level, Speaker Setup, Digital Input Select and Delay functions may also be adjusted using the OSD on-screen menus. I

42、n addition, the EzSet/EQ system may be used to adjust the Channel Level, Speaker Setup and Delay settings automatically. Numeric Keys: Use these buttons to enter radio station frequencies or to select station presets. Press the Direct Button before entering the station frequency. Tuning Mode: This b

43、utton toggles between manual (one frequency step at a time) and automatic (seeks frequencies with acceptable signal strength) tuning mode. It also toggles between stereo and mono modes when an FM station is tuned. Memory: After you have tuned a particular radio station, press this button, then the N

44、umeric Keys, to save that station as a radio preset. Tuning: Press these buttons to tune a radio station. Depending on whether the tuning mode has been set to manual or automatic, each press will either change one frequency step at a time, or seek the next frequency with acceptable signal strength.

45、harman/kardonAVR 160/230 Service Manual 6 of 116 RadioFans.CN 13 ENGLISH REMOTE CONTROL FUNCTIONS Direct: Press this button before using the Numeric Keys to directly enter a radio station frequency. Clear: Press this button to clear a radio station frequency you have started to enter. Preset Station

46、s Selector: Press these buttons to select a preset radio station. Tone Mode: Press this button to access the tone controls (bass and treble). Use the Navigation Buttons to make your selections. RDS: Activates RDS functions for FM Radio Macros: These buttons may be programmed to execute long command

47、sequences with a single button press. They are useful for programming the command to turn on or off all of your components, or for accessing specialized functions for a different component than you are currently operating. Night Mode: Press this button to activate Night mode with specially encoded D

48、olby Digital discs or broadcasts. Night mode compresses the audio so that louder passages are reduced in volume to avoid disturbing others, while dialogue remains intelligible. Track Skip: These buttons have no effect on the receiver, but are used with many source components to change tracks or chap

49、ters. Dim: Press this button to partially or fully dim the front-panel display. Transport Controls: These buttons have no effect on the receiver, but are used to control many source components. By default, when the remote is operating the receiver, these buttons will control a Harman Kardon Blu-ray Disc player or a DVD player. Instructions for users on removal and disposal of used batteries. Specification of included batter