HarmanKardon-AVR110-avr-sm维修电路图 手册.pdf

《HarmanKardon-AVR110-avr-sm维修电路图 手册.pdf》由会员分享，可在线阅读，更多相关《HarmanKardon-AVR110-avr-sm维修电路图 手册.pdf（127页珍藏版）》请在收音机爱好者资料库上搜索。

1、 harman/kardon AVR110 AVR110 A/V DOLBY DIGITAL RECEIVER SERVICE MANUAL CONTENTS ESD WARNING.2 LEAKAGE TESTING.3 BASIC SPECIFICATIONS.4 FRONT PANEL CONTROLS.5 REAR PANEL CONNECTIONS.9 REMOTE CONTROL FUNCTIONS.11 TROUBLESHOOTING GUIDE.14 PROCESSOR RESET.14 IDLE CURRENT/TUNER ALIGNMENT.15 BULLETIN # H/

2、K2001-01.16 BULLETIN # H/K2001-03.18 BULLETIN # H/K2003-07.19 TECH TIP# HKTT2002-01.21 TECH TIP# HKTT2003-01.23 UNIT EXPLODED VIEW.24 EXPLODED VIEW PARTS LIST.25 BLOCK DIAGRAMS.26 PCB DRAWINGS.28 ELECTRICAL PARTS LIST.40 SEMICONDUCTOR PINOUTS.61 SCHEMATICS.109 WIRING DIAGRAM.124 PACKAGE.127 harman/k

3、ardon, Inc. 250 Crossways Park Dr. Woodbury, New York 11797 Rev2 6/2005 RadioFans.CN Eachprecautioninthismanualshouldbefollowedduringservicing. Components identified with the IEC symbolin the parts list are special significance to safety. When replacing a component identified with , use only the rep

4、lacement parts designated, or parts with the same ratings or resistance, wattage, or voltage that are designated in the parts list in this manual. Leakage-current or resistance measurements must be made to determine that exposed parts are acceptably insulated from the supply circuit before retuming

5、the product to the customer. Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are called Electrostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field effect transistors and semiconductor

6、chip components. The following techniques should be used to help reduce the incidence of component damage caused by static electricity. 1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any electrostatic charge on your body by touching a known e

7、arth ground. Alternatively, obtain and wear a commercially available discharging wrist strap device, which should be removed for potential shock reasons prior to applying power to the unit under test. 2. After removing an electrical assembly equipped with ES devices, place the assembly on a conducti

8、ve surface such as aluminum foil, to prevent electrostatic charge build-up or exposure of the assembly. 3. Use only a grounded-tip soldering iron to solder or unsolder ES devices. 4. Use only an anti-static solder removal device. Some solder removal devices not classified as anti-static can generate

9、 electrical charges sufficient to damage ES devices. 5. Do not use freon-propelled chemicals. These can generate electrical change sufficient to damage ES devices. 6. Do not remove a replacement ES device from its protective package until immediately before you are ready to install it. (Most replace

10、ment ES devices are packaged with leads electrically shorted together by conductive foam, aluminum foil or comparable conductive material.) 7. Immediately before removing the protective material from the leads of a replacement ES device, touch the protective material to the chassis or circuit assemb

11、ly into which the device will be installed. Be sure no power is applied to the chassis or circuit, and observe all other safety precautions. 8. Minimize bodily motions when handling unpackaged replacement ES devices. (Otherwise harmless motion such as the brushing together or your clothes fabric or

12、the lifting of your foot from a carpeted floor can generate static electricity sufficient to damage an ES devices. CAUTION : AVR110 AVR110 harman/kardon 2 RadioFans.CN 1. Inspect all lead dress to make certain that leads are not pinched or that hardware is not lodged between the chassis and other me

13、tal partsintheunit. 2. Be sure that any protective devices such as nonmetallic control knobs, insulating fish- papers,cabinetbacks,adjustmentand compartment covers or shields, isolation resistor-capacitynetworks,mechanical insulators, etc. Which were removed for the servicingareproperlyre-installed.

14、 Before returning the unit to the user, perform the following safety checks : 3. Be sure that no shock hazard exists ; check for leakage currentusingSimpsonModel229LeakageTester,standard equipment item No. 21641, RCA Model WT540A or use alternate method asfollows : Plug the power cord directly Into

15、a 120 volt AC receptacle (do not use an Isolation Transformer for this test). Using two clip leads, connect a 1500ohms,10wattResistorparalleledbya0.15uFcapacitor,inserieswithallexposedmetalcabinetpartsandaknownearthground,such as a water pipe or conduit. Use a VTVM or VOM with 1000 ohms per volt, or

16、 higher sensitivity to measure the AC voltage drop across the resistor. (See diagram) Move the resistor connection to each exposed metal part having a return path to the chassis (antenna, metal, cabinet,screwheads,knobsandcontrolshafts,escutcheon,etc.)andmeasuretheACvoltagedropacrosstheresistor.(Thi

17、stestshouldbe performedwiththe0.35voltRMSormoreisexcessiveandindicatesapotentialshockhazardwhichmustbecorrectedbeforereturningthe unittotheowner. AVR110 AVR110 harman/kardon 3 RadioFans.CN 4 TECHNICAL SPECIFICATIONS Technical Specifications Audio Section Stereo Mode Continuous Average Power (FTC) 50

18、 Watts per channel, 20Hz20kHz, 0.07% THD, both channels driven into 8 ohms Five-Channel Surround Mode Power per Individual Channel Front L press it again to turn the unit off. Note that the Power Indicator surrounding the switch 3 will turn green when the unit is on. 3 Power Indicator: This LED will

19、 be illumi- nated in amber when the unit is in the Standby mode to signal that the unit is ready to be turned on.When the unit is in operation, the indicator will turn green. 4 Headphone Jack:This jack may be used to listen to the AVR 110s output through a pair of headphones. Be certain that the hea

20、dphones have a standard 1/4 stereo phone plug. Note that the main room speakers will automatically be turned off when the headphone jack is in use. 5 Selector Buttons:When you are establish- ing the AVR 110s configuration settings,use these buttons to select from the choices available, as shown in t

21、he Main Information Display . 6 Tone Mode: Pressing this button enables or disables the Bass and Treble tone controls. When the button is pressed so that the words TONE IN appear in the Main Information Display , the settings of the Bass the tuner will automatically scan for the next station with an

22、 acceptable signal and then stop. 9 Tuner Band Selector: Pressing this button will automatically switch the AVR 110 to the Tuner mode. Pressing it again will switch between the AM and FM frequency bands. (See page 25 for more information on the tuner.) ) Preset Stations Selector: Press this button t

23、o scroll up or down through the list or stations that have been entered into the preset memory. (See page 26 for more information on preset tuning.) ! Input Source Selector: Press this button to change the input by scrolling up or down through the list of input sources. FM Mode Selector: Press this

24、button to select Auto or Manual tuning.When the button is pressed so that the AUTO indicator V lights, the tuner will search for the next station with an acceptable signal when the Tuning Selector 8u is pressed.When the button is pressed so that the AUTO indicator V is not lit, each press of the Tun

25、ing Selector 8u will increase the frequency. (See page 25 for more information on using the tuner.) # Digital Optical 3 Input: Connect the opti- cal digital output of an audio or video product to this jack.When the Input is not in use, be certain to keep the plastic cap installed to avoid dust conta

26、mination that might degrade future performance. $ Digital Coax 3 Jack: This jack is used for connection to the output of portable audio devices, video game consoles or other products that have a coax digital jack. % Video 4 Video Input Jacks: These jacks may be used for temporary connection to the c

27、omposite or S-Video output of video games, camcorders or other portable video products. Video 4 Audio Input Jacks: These audio/video jacks may be used for temporary connection to video games or portable audio/video products such as camcorders and portable audio players. VMAx N appears when the Near

28、Field VMAx mode is selected. (See page 22 for a description of the VMAx modes.) J 5-Channel Stereo Indicator: This indica- tor lights when the 5-Channel Stereo mode has been selected. K Logic 7 Mode Indicators: These indica- tors light when the Logic 7 mode is in use. LOGIC 7C appears for the Cinema

29、 version of Logic 7; LOGIC 7M appears for the Music version of Logic 7. (See page 22 for a description of the Logic 7 modes.) L Hall Mode Indicator: This indicator lights when the Hall mode has been selected. M Theater Mode Indicator:This indicator lights to show that the Theater mode has been selec

30、ted. N Night Mode Indicator: This indicator lights when the AVR 110 is in the Night mode, which preserves the dynamic range of digital program material at low volume levels. O Speaker/Channel Input Indicators: These indicators are multipurpose, indicating either the speaker type selected for each ch

31、annel or the incoming data-signal configuration.The left, center, right, right surround and left surround speaker indicators are composed of three boxes, while the subwoofer is a single box.The center box lights when a “Small” speaker is selected, and all three boxes light when “Large” speakers are

32、selected.When none of the boxes are lit for the center, surround or subwoofer channels, no speaker has been selected for one of those posi- tions. (See page 17 for more information on con- figuring speakers.) The letters inside each of the center boxes display active input channels. For standard ana

33、log inputs, only the L and R will light, indicating a stereo input.When a digital source is playing, the indicators will light to dis- play the channels being received at the digital input.When the letters flash, the digital input has been interrupted. (See page 18 for more information on the Channe

34、l Indicators.) P Preset Number/Sleep Timer: When the tuner is in use, these numbers indicate the spe- cific preset memory location in use. (See page 25 for more information on preset stations.) When the Sleep function is in use, these num- bers show how many minutes remain before the unit goes into

35、the Standby mode. Q Preset Indicator: This indicator lights when the tuner is in use to show that the Preset Number/Sleep Timer P is showing the stations preset memory number. (See page 25 for more information on tuner presets.) R Sleep Indicator: This indicator lights when the Sleep function is in

36、use.The numbers in the Preset Number/Sleep Timer Indicators will show the minutes remaining before the AVR 110 goes into the Standby mode. (See page 21 for more information on the Sleep function.) AVR110 AVR110 harman/kardon RadioFans.CN 8 FRONT PANEL INFORMATION DISPLAY Front Panel Information Disp

37、lay SMemory Indicator: This indicator flashes when entering presets and other information into the tuners memory. T Stereo Indicator:This indicator lights when an FM station is being tuned in stereo. UTuned Indicator:This indicator lights when a station is being received with sufficient signal stren

38、gth to provide acceptable listening quality. V Auto Indicator: This indicator lights when the tuners Auto mode is in use. W Main Information Display: This display shows messages relating to the status, input source, surround mode, tuner, volume level or other aspects of the AVR 110s operation. X Mut

39、e Indicator: This indicator lights to remind you that the AVR 110s output has been silenced by pressing the Mute button . Press the Mute button again to return to the pre- viously selected output level. 35 AVR110 AVR110 harman/kardon RadioFans.CN 9 REAR PANEL CONNECTIONS Rear Panel Connections ? fi

40、? fl ? ?a b c d e f g j ? ? ? ? h k ? ? ? ? ? ? ? i ? Manufactured under license from Dolby Laboratories. Dolby,Pro Logic and the double-D symbol are trademarks of Dolby Laboratories. Confidential Unpublished Works. 1992-1997 Dolby Laboratories,Inc. All rights reserved. c Manufactured under license

41、from Digital Theater Systems, Inc. US Pat. No. 5,451,942 and other world-wide patents issued and pending. DTS, DTS Digital Surround, are trademarks of Digital Theater Systems, Inc. Copyright 1996 Digital Theater Systems,Inc. All Rights Reserved. This device complies with part 15 of the FCC rules. Op

42、eration is subject to the following two conditions; (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. REMOTE U.S. Patent Nos. 4,893,342, 4,910,779, 4,975,954, 5,034,983, 5,136,651,

43、 and 5,333,200 Cooper Bauck Transaural Stereo. Tape Inputs Tape Outputs Video 1 Audio Inputs AM Antenna Video 1 Audio Outputs DVD Audio Inputs FM Antenna CD Inputs Digital Audio Outputs DVD Video Inputs Video Monitor Outputs Subwoofer Output Front Speaker Outputs Center Speaker Outputs fi Surround S

44、peaker Outputs fl Switched AC Accessory Outlet Unswitched AC Accessory Outlet AC Power Cord Remote IR Output a Remote IR Input b Video 1 Video Outputs c Video 1 Video Inputs d Video 3 Video Inputs e Video 2 Video Inputs f Video 2 Video Outputs g Optical Digital Inputs h Coaxial Digital Inputs i Vide

45、o 2 Audio Outputs jVideo 3 Audio Inputs kVideo 2 Audio Inputs AVR110 AVR110 harman/kardon RadioFans.CN 10 REAR PANEL CONNECTIONS Rear Panel Connections Tape Inputs: Connect these jacks to the PLAY/OUT jacks of an audio recorder. Tape Outputs: Connect these jacks to the RECORD/INPUT jacks of an audio

46、 recorder. Video 1 Audio Inputs: Connect these jacks to the PLAY/OUT audio jacks on a VCR or other video source. AMAntenna: Connect theAM loop antenna supplied with the receiver to these terminals.If an externalAM antenna is used,make connections to the AM and GND terminals in accordance with the in

47、structions supplied with the antenna. Video 1 Audio Outputs: Connect these jacks to the RECORD/INPUT audio jacks on a VCR. DVD Audio Inputs: Connect these jacks to the analog audio jacks on a DVD or other video source. FM Antenna: Connect the supplied indoor or an optional external FM antenna to thi

48、s terminal. CD Inputs: Connect these jacks to the out- put of a compact disc player or CD changer. Digital Audio Outputs: Connect these jacks to the matching digital input connector on a digital recorder such as a CD-R or MiniDisc recorder. DVD Video Inputs: Connect these jacks to the composite or S

49、-Video output jacks on a DVD or other video source. Video Monitor Outputs: Connect this jack to the composite or S-Video input of a TV monitor or video projector to view the output of any standard video source selected by the receivers video switcher. Subwoofer Output: Connect this jack to the line-level input of a powered subwoofer. If an external subwoofer