Denon-DNX100-mix-sm维修电路图 手册.pdf
《Denon-DNX100-mix-sm维修电路图 手册.pdf》由会员分享,可在线阅读,更多相关《Denon-DNX100-mix-sm维修电路图 手册.pdf(34页珍藏版)》请在收音机爱好者资料库上搜索。
1、SERVICE MANUAL DJ MIXER MODELDN-X100 For U.S.A., Canada, Europe, U.K., Asia, China, Taiwan R.O.C., Korea & Japan model TOKYO, JAPAN X0213V.01 DE/CDM 0409 Some illustrations using in this service manual are slightly different from the actual set. Please use this service manual with referring to the o
2、perating instructions without fail. For purposes of improvement, specifications and design are subject to change without notice. 本文中使用、説明都合上現物 多少異場合。 修理際、必取扱説明書参照上、作業行 。 前、 必読。本機、火災、感電、 対安全性確保、配慮 、法的電気用品安全法 、所定許可得製造。 従際、安全性維 持、記載 注意事項必守。 本機仕様性能改良、予告変更 。 補修用性能部品保有期間、製造打切後8年。 注意 Ver. 1 RadioFans.CN 2
3、DN-X100 SAFETY PRECAUTIONS The following check should be performed for the continued protection of the customer and service technician. LEAKAGE CURRENT CHECK Before returning the unit to the customer, make sure you make either (1) a leakage current check or (2) a line to chassis resistance check. If
4、 the leakage current exceeds 0.5 milliamps, or if the resistance from chassis to either side of the power cord is less than 460 kohms, the unit is defective. (1) (2) 500V 1M (1) (2) RadioFans.CN 3 DN-X100 DISASSEMBLY (Follow the procedure below in reverse order when reassembling.) 1. Top Panel (1) P
5、ull out the Knobs from the Top Panel. (2) Remove the 6 screws attaching the Top Panel. (3) Pull up the Top Panel. RadioFans.CN 4 DN-X100 2. Crossfader Unit (1) Remove the 2 screws attaching the Crossfader Unit. (2) Pull up the Crossfader Unit and disconnect the connector. Note: ? Be careful in the a
6、ttachment direction. 3. Channel Fader Unit (1) Remove the 3 screws attaching the Channel Fader Unit. (2) Pull up the Channel Fader Unit and disconnect the connector. RadioFans.CN 5 DN-X100 4. Input Selector Unit (1) Remove the 2 screws attaching the Input Selector Unit. (2) Pull up the Input Selecto
7、r Unit and disconnect the connector. Note: ? Be careful in the attachment direction. 5. Top Panel Unit (1) Remove the 6 screws from the both-sides side. (2) Remove the 2 screws from the rear side. (3) Remove the 5 screws from the front side. (4) Remove the 4 screws from the bottom side. (5) Pull up
8、the front side of the Top Unit. (6) Disconnect the connectors. RadioFans.CN 6 DN-X100 BLOCK DIAGRAM RadioFans.CN 7 DN-X100 SEMICONDUCTORS Only major semiconductors are shown, general semiconductors etc. are omitted to list. 主半導体記載。汎用半導体記載省略。 1. ICs MAX003 (IC801) MAX003 Terminal Function Pin No. Pin
9、 NameSymbolI/ODetInt PuExtResIniFunction 1VCLVCL- VCL(capacitor between this pin and GND)in 5V operation models,and as Vcc in 3V operation models. 2PB0CH1FSI-PuLHCH1 FADER START SW L : ON 3PB1PB1O-PuLLNot used 4PB2PB2O-PuLLNot used 5PB3PB3O-PuLLNot used 6PB4PB4O-PuLLNot used 7PB5PB5O-PuLHNot used 8P
10、B6FX2SWI-PuLHPGM2 EFFECT LOOP ON/OFF SW L : ON (DN-X300 only) 9PB7CHREVI-PuLHCH REVERSE SW L : ON 10_RESO_RESOO-Not used 11VssVss-GND(0V) 12P90P90O-LLNot used 13P91P91O-LLNot used 14P92P92O-LLNot used 15P93P93O-LLNot used 16P94P94O-LLNot used 17P95P95O-LLNot used 18P40P40O-ON-LLNot used 19P41P41O-ON
11、-LLNot used 20P42P42O-ON-LLNot used 21P43PC1AI/O-ON-LHPGM1 Fader PLAY output 30msec L pulse 22VssVss-GND(0V) 23P44PC1BI/O-ON-LHPGM1 Fader CUE output 30msec L pulse 24P45PC2AI/O-ON-LHPGM2 Fader PLAY output 30msec L pulse 25P46PC2BI/O-ON-LHPGM2 Fader CUE output 30msec L pulse 26P47P47O-ON-LLNot used 2
12、7D8D0D/I-Data bus 28D9D1D/I-Data bus 29D10D2D/I-Data bus 30D11D3D/I-Data bus 31D12D4D/I-Data bus 32D13D5D/I-Data bus 75 76 100 125 26 50 51 RadioFans.CN 8 DN-X100 33D14D6D/I-Data bus 34D15D7D/I-Data bus 35VccVcc-Power supply(+5V) 36A0A0A/O-Address bus 37A1A1A/O-Address bus 38A2A2A/O-Address bus 39A3
13、A3A/O-Address bus 40A4A4A/O-Address bus 41A5A5A/O-Address bus 42A6A6A/O-Address bus 43A7A7A/O-Address bus 44VssVss-GND(0V) 45A8A8A/O-Address bus 46A9A9A/O-Address bus 47A10A10A/O-Address bus 48A11A11A/O-Address bus 49A12A12A/O-Address bus 50A13A13A/O-Address bus 51A14A14A/O-Address bus 52A15A15A/O-A
14、ddress bus 53A16A16A/O-Address bus 54A17A17A/O-Address bus 55P52_FX1ONO-ON-LHPGM1 EFFECT LOOP enabler L : enabler (DN-X300 only) 56P53_FX2ONO-ON-LHPGM2 EFFECT LOOP enabler L : enabler (DN-X300 only) 57VssVss-GND(0V) 58P60LEDFX1O-PuLHPGM1 EFFECT LOOP LED control. (DN-X300 only) 59P61LEDFX2O-PuLHPGM2
15、EFFECT LOOP LED control. (DN-X300 only) 60P62FX1SWI-LHPGM1 EFFECT LOOP ON/OFF SW L : ON (DN-X300 only) 61P67P67I-HHDN-X100/300 program selected Pin L : DN-X300 62_STBY_STBY-HWhen driven low,this pin forces a transition to hardware standby mode. 63_RES_RES-Reset signal L : Reset 64NMINMII-Pu-HNot use
16、d 65VssVss-GND(0V) 66EXTALEXTAL-OSC 16MHz 67XTALXTAL-OSC 16MHz 68VccVcc-Power supply(+5V) 69_AS_AS-Not used 70_RD_RDO-Goes low to indicate reading from the external address space 71_HWR_HWR-Not used 72P66JDETI-LHCheck Send Return jack inserted 73MD0MD0I-IC Operating mode control 74MD1MD1I-IC Operati
17、ng mode control 75MD2MD2I-IC Operating mode control 76AvccAvcc-Power supply pin for the A/D converters(+5V). 77VrefVref-Reference voltage input pin for the A/D converters(+5V). 78P70,AN0CH1FADERI-Hi-zCH1 FADER VR A/D converter 79P71,AN1CFFADERI-Hi-zCROSS FADER VR A/D converter 80P72,AN2CH2FADERI-Hi-
18、zCH2 FADER VR A/D converter 81P73,AN3CH1CUREVI-Hi-zCH1 FADER CONTOUR VR A/D converter 82P74,AN4CFCUREVI-Hi-zCROSS FADER CONTOUR VR A/D converter 83P75,AN5CH2CUREVI-Hi-zCH2 FADER CONTOUR VR A/D converter 84P76,AN6AN6I-Hi-zNot used 85P77,AN7AN7I-Hi-zNot used 86AvssAvss-Ground pin for A/D converters(0V
19、). 87P80P80O-PuLLNot used Pin No. Pin NameSymbolI/ODetInt PuExtResIniFunction RadioFans.CN 9 DN-X100 88P81P81O-PuLLNot used 89P82P82O-PuLLNot used 90P83CH1REVO-PuLHCH1 FADER REVERSE SW L : ON 91P84,_CS_CEO-LLChip select signal. 92VssVss-GND(0V) 93PA0CFREVI-PuLHCROSSFADER REVERSE SW L : ON 94PA1CH2RE
20、VI-PuLHCH2 FADER REVERSE SW L : ON 95PA2CH2FSI-PuLHCH2 FADER START SW L : ON 96PA32CFSI-PuLHCROSSFADER START B SW L : ON 97PA4C1O-LHPWM output control PGM1 volume 98PA51CFSI-PuLHCROSSFADER START A SW L : ON 99PA6C2O-LHPWM output control PGM2 volume 100PA7PA7O-PuLLNot used Pin No. Pin NameSymbolI/ODe
21、tInt PuExtResIniFunction RadioFans.CN 10 DN-X100 LB1482M (IC701) TC4053BF (IC507)NJM2060 (IC105, 106, 205, 206, 952) LB1482M 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 21 20 19 18 17 16 27 26 25 30 29 28 24 23 22 PH D1 CH2 IN OSC NC Vcc1 Vcc2 MUTE CH1 IN CR1 8P/5P AC/DC A GND DC IN CR2 O9 O10 O11 O12 D2 NC
22、 O3 O4 O5 GND O1 O2 O6 O7 O8 AC IN (1) AC IN (2) DC IN Inside reference voltage OSC LOGIC CONTROL PEAK HOLD LOGIC CONTROL SWITCHER O1 D1 Vcc2 (Power system) 8P/5PAC DC P/HMUTE OSC GND Vcc1 A GND CH1 IN CH2 IN DC IN CR1 CR2 (Signal system) O2 D2 O3 O4 O5 O6 O7 O8 O9 O10 O11 O12 19 27282930 17 16 14 2
23、 3 4 5 6 7 8 9 10 11 12 13 1 24 18 23 22 21 25 26 IY OY IZ Z-COM OZ INH VEE Vss 1 2 3 4 5 6 7 8 16 15 14 13 12 11 10 9 VDD Y-COM X-COM IX OX A B C 1A OUTPUT B OUTPUT V+ A +INPUT B +INPUT A -INPUT B -INPUT D OUTPUT C OUTPUT V- D +INPUT C +INPUT D -INPUT C -INPUT AD B C 2 3 4 5 6 7 14 13 12 11 10 9 8
24、RadioFans.CN 11 DN-X100 M51132L (IC109, 209) 1M FLASH MEMORY (IC802)ADG212A (IC113, 213) BD4745G (IC803) 14 13 12 11 10 9 8 7 6 5 4 3 2 1 Ref Control mode switching Filter NC GND Output 1 Output 2 Input 1 Input 2 Power Volume/Volume 1 control Shock noise reduction at Bus Through SW switching Bus Thr
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- Denon-DNX100-mix-sm维修电路图 手册 Denon DNX100 mix sm 维修 电路图