Denon-AVR4310CI-avr-sm维修电路图 手册.pdf

《Denon-AVR4310CI-avr-sm维修电路图 手册.pdf》由会员分享，可在线阅读，更多相关《Denon-AVR4310CI-avr-sm维修电路图 手册.pdf（211页珍藏版）》请在收音机爱好者资料库上搜索。

1、D&M Holdings lnc. e SERVICE MANUAL AV SURROUND RECEIVER AV SURROUND AMPLIFIER MODELJPEUECE2EKE2AE1CEUT AVR-4310CI ? AVR-4310 ? ? MODELJPEUECE2EKE2AE1CEUT AVC-4310 ? ? s d Ver. 6 For purposes of improvement, specifications and design are subject to change without notice. Please use this service manua

2、l with referring to the operating instructions without fail. Some illustrations using in this service manual are slightly different from the actual set. S0025-1V06DM/DG0912 Please refer to the MODIFICATION NOTICE. RadioFans.CN 2 AVR-4310CI/AVR-4310/AVC-4310 Please heed the points listed below during

3、 servicing and inspection. Heed the cautions! Spots requiring particular attention when servicing, such as the cabinet, parts, chassis, etc., have cautions indicated on labels or seals. Be sure to heed these cautions and the cautions indicated in the handling instructions. Caution concerning electri

4、c shock! (1) An AC voltage is impressed on this set, so touching in- ternal metal parts when the set is energized could cause electric shock. Take care to avoid electric shock, by for example using an isolating transformer and gloves when servicing while the set is energized, un- plugging the power

5、cord when replacing parts, etc. (2)There are high voltage parts inside. Handle with extra care when the set is energized. Caution concerning disassembly and assembly! Though great care is taken when manufacturing parts from sheet metal, there may in some rare cases be burrs on the edges of parts whi

6、ch could cause injury if fingers are moved across them. Use gloves to protect your hands. Only use designated parts! The sets parts have specific safety properties (fire resis- tance, voltage resistance, etc.). For replacement parts, be sure to use parts which have the same properties. In par- ticul

7、ar, for the important safety parts that are marked z on wiring diagrams and parts lists, be sure to use the desig- nated parts. Be sure to mount parts and arrange the wires as they were originally! For safety reasons, some parts use tape, tubes or other in- sulating materials, and some parts are mou

8、nted away from the surface of printed circuit boards. Care is also taken with the positions of the wires inside and clamps are used to keep wires away from heating and high voltage parts, so be sure to set everything back as it was originally. Inspect for safety after servicing! Check that all screw

9、s, parts and wires removed or discon- nected for servicing have been put back in their original po- sitions, inspect that no parts around the area that has been serviced have been negatively affected, conduct an insu- lation check on the external metal connectors and between the blades of the power

10、plug, and otherwise check that safety is ensured. (Insulation check procedure) Unplug the power cord from the power outlet, disconnect the antenna, plugs, etc., and turn the power switch on. Us- ing a 500V insulation resistance tester, check that the in- sulation resistance between the terminals of

11、the power plug and the externally exposed metal parts (antenna ter- minal, headphones terminal, microphone terminal, input terminal, etc.) is 1M or greater. If it is less, the set must be inspected and repaired. Concerning important safety parts Many of the electric and structural parts used in the

12、set have special safety properties. In most cases these prop- erties are difficult to distinguish by sight, and using re- placement parts with higher ratings (rated power and withstand voltage) does not necessarily guarantee that safety performance will be preserved. Parts with safety properties are

13、 indicated as shown below on the wiring dia- grams and parts lists is this service manual. Be sure to re- place them with parts with the designated part number. (1) Schematic diagrams . Indicated by the z mark. (2) Parts lists . Indicated by the z mark. Using parts other than the designated parts co

14、uld result in electric shock, fires or other dangerous situations. SAFETY PRECAUTIONS The following check should be performed for the continued protection of the customer and service technician. LEAKAGE CURRENT CHECK Before returning the unit to the customer, make sure you make either (1) a leakage

15、current check or (2) a line to chassis resistance check. If the leakage current exceeds 0.5 milliamps, or if the resistance from chassis to either side of the power cord is less than 460 kohms, the unit is defective. CAUTION CAUTION RadioFans.CN 3 AVR-4310CI/AVR-4310/AVC-4310 DIMENSION AVR-4310CI/AV

16、R-4310/AVC-4310 344 434 155 15.5 170.5 20.7 244.5 372.8 20.5 414 54.7 RadioFans.CN 4 AVR-4310CI/AVR-4310/AVC-4310 WIRE ARRANGEMENT If wire bundles are untied or moved to perform adjustment or parts replacement etc., be sure to rearrange them neatly as they were originally bundled or placed afterward

17、. Otherwise, incorrect arrangement can be a cause of noise generation. Wire arrangement viewed from the top Front Panel side Back Panel side RadioFans.CN 5 AVR-4310CI/AVR-4310/AVC-4310 CAUTION IN SERVICING Before the Digital P.W.B. are replaced If you cannot specify the cause of the digital PWB defe

18、ct, carry out Initializing Update to latest firmware. The defect may be cleared. See the following for the method of initializing the com. Initializing AV SURROUND RECEIVER AV SURROUND RECEIVER initialization should be performed when the com, peripheral parts of com, and Digital P.W.B. are replaced.

19、 1. Switch off the unit. 2. Hold the following STANDARD button and DSP SIMULATION button, and switch on the unit. 3. Check that the entire display is flashing with an interval of about 1 second, and release your fingers from the 2 buttons and the microprocessor will be initialized. Note:If step 3 do

20、es not work, start over from step 1. All user settings will be lost and this factory setting will be recovered when this initialization mode. So make sure to memorize your setting for restoring after the initialization. JIG to use for servicing When you repair the printing board, you can use the fol

21、lowing JIG. Please order to Denon Official Service Distributor in your region if necessary. Extention cable kit 00D SPK- 561 EXTENSION UNIT KIT : 1 Set 00D SPK- 562 TUCP CONN. JOINT KIT : 1 Set Extention cable for Idling Current Parts Number for Extension Cables and Quantity of Unit. How to use and

22、Adjust Idle Current. 1. The thin and hard plate (ex. Ruler) is fixed with the tape behind the cable. 2. The voltmeter is connected with the other side of the extension cable. 3. Refer to ADJUSTMENT(Idling Current). Parts NumberParts NameQty / unitRemarks 612050082004D6P 250mm NH1L=250mm 6P NH Cable

23、612050083007D8P 250mm NH1L=250mm 8P NH Cable 1,22,3 RadioFans.CN 6 AVR-4310CI/AVR-4310/AVC-4310 DISASSEMBLY Disassemble in order of the arrow of the figure of following flow. In the case of the re-assembling, assemble it in order of the reverse of the following flow. In the case of the re-assembling

24、, observe attention of assembling it. TOP COVER BACK PANEL UNIT ASSYFRONT PANEL UNIT ASSY Refer to DISASSEMBLYREG UNITRefer to DISASSEMBLY 2. BACKPANEL UNIT ASSYRefer to DISASSEMBLY1.FRONT PANEL UNIT ASSY 5. REG UNITP.SW UNIT and EXPLODED VIEW (Ref. No. of EXPLODED VIEW : A-8) DIGITAL UNIT ASSYREG U

25、NIT FRONT HDMI UNIT Refer to DISASSEMBLY (Ref. No. of EXPLODED VIEW : B-4) (Ref. No. of EXPLODED VIEW : E-4) 3. DIGITAL UNIT ASSYREG CONNECT-1 UNITFRONT USB UNIT and EXPLODED VIEW (Ref. No. of EXPLODED VIEW : A-15) (Ref. No. of EXPLODED VIEW : E-3) DIGITAL UNIT CONNECT UNIT-2MIC UNIT (Ref. No. of EX

26、PLODED VIEW : G) (Ref. No. of EXPLODED VIEW : D-4) (Ref. No. of EXPLODED VIEW : A-9) FRONT IN UNIT (Ref. No. of EXPLODED VIEW : A-10) A.VIDEO UNIT, AUDIO UNIT AMP UNITVR CONNECT UNIT and RADIATOR UNIT ASSYRefer to DISASSEMBLY (Ref. No. of EXPLODED VIEW : A-5) Refer to DISASSEMBLY6. AMP UNITVOLUME UN

27、IT 4. A.VIDEO UNIT, AUDIO UNITand EXPLODED VIEW (Ref. No. of EXPLODED VIEW : A-4) and RADIATOR UNIT ASSYAMP UNITFUNC CONNECT UNIT and EXPLODED VIEW (Ref. No. of EXPLODED VIEW : D-1) (Ref. No. of EXPLODED VIEW : A-7) A.VIDEO UNITFUNC UNIT (Ref. No. of EXPLODED VIEW : E-1) (Ref. No. of EXPLODED VIEW :

28、 A-6) AUDIO UNITP.AMP JOINT UNITFLD UNIT (Ref. No. of EXPLODED VIEW : E-2)Refer to DISASSEMBLY (Ref. No. of EXPLODED VIEW : A-1) MAIN CPU UNIT7. P.AMP JOINT UNIT (Ref. No. of EXPLODED VIEW : F)and EXPLODED VIEW REMOTE/IPOD UNITP.AMP JOINT UNIT (Ref. No. of EXPLODED VIEW : B-5) (Ref. No. of EXPLODED

29、VIEW : D-2) 232C UNIT (Ref. No. of EXPLODED VIEW : B-6) P.AMP UNIT Refer to DISASSEMBLY 9.P.AMP UNIT and EXPLODED VIEW P.AMP UNIT (Ref. No. of EXPLODED VIEW : D-17) RadioFans.CN 7 AVR-4310CI/AVR-4310/AVC-4310 About the photos used for descriptions in the “DISASSEMBLY” section. The direction from whi

30、ch the photographs used herein were photographed is indicated at Direction of photograph: * at the left of the respective photographs. Refer to the table below for a description of the direction in which the photos were taken. Photographs for which no direction is indicated were taken from above the

31、 product. 1. FRONT PANEL UNIT ASSY (1) Remove the screws. (2) Cut the wire clampers then disconnect the connector wires. Front side Direction of photograph: B Direction of photograph: DDirection of photograph: C Direction of photograph: A The viewpoint of each photograph (Photografy direction) View

32、from above Proceeding:TOP COVER FRONT PANEL UNIT ASSY View from bottom CX021 CY062 Direction of photograph: D cut cut cut RadioFans.CN 8 AVR-4310CI/AVR-4310/AVC-4310 (3) Remove the FFC cover and acetate tapes. Disconnect the FFC Cables. (4) Remove the screws. Attention of assembling When mounting th

33、e FRONT PANEL ASSY on the CHASSIS, do so with the DOOR open so as to prevent breaking the EARTH PLATE(DOOR). If the FRONT PANEL ASSY is mounted on the chassis with the DOOR closed, the EARTH PLATE(DOOR) will hit the CHASSIS and break. Acetate tape FFC Cover FFC Cable Direction of photograph: C FFC C

34、able ? Please refer to EXPLODED VIEW for the disassembly method of each P.W.B included in FRONT PANEL ASSY. DOOR open DOOR closed (EARTH PLATE (DOOR) will be broken.) EARTH PLATE (DOOR) DOOR DOOR EARTH PLATE (DOOR) Direction of photograph: A Direction of photograph: A RadioFans.CN 9 AVR-4310CI/AVR-4

35、310/AVC-4310 2. BACK PANEL UNIT ASSY (1) Remove the Sheets, then remove the screws. (2) Remove the screws. (3) Disconnect the connector wires and FFC Cable, then remove the screws. Proceeding:TOP COVER BACK PANEL UNIT ASSY Sheets View from bottom ? ? Direction of photograph: A CY153 CY101 CX055 CX07

36、4 FFC Cable CY052 RadioFans.CN 10 AVR-4310CI/AVR-4310/AVC-4310 (4) Remove the FFC cover, PWB HOLDER and acetate tapes. Cut the wire clamper, then disconnect the connector wire and FFC Cable. (5) Cut the wire clamper, then disconnect the connector wire. FFC Cable CX068 PWB HOLDER Direction of photogr

37、aph: C cut Acetate tapeAcetate tapeFFC Cover v Direction of photograph: D BACK PANEL UNIT ASSY CX091 cut RadioFans.CN 11 AVR-4310CI/AVR-4310/AVC-4310 3. DIGITAL UNIT ASSY (1) Remove the alminium tape, then cut the wire clampers. Disconnect the connector wire, FFC Cables, and board to board. (2) Remo

38、ve the screws. Proceeding:TOP COVER BACK PANEL UNIT ASSY DIGITAL UNIT ASSY FFC Cable FFC Cable FFC CablecutcutMAIN CPU UNIT DIGTAL UNIT ASSY Board to board CX058 CX124 CX047 CY061Alminium Tape CY124 ? Direction of photograph: A RadioFans.CN 12 AVR-4310CI/AVR-4310/AVC-4310 4. A.VIDEO UNIT, AUDIO UNIT

39、 and RADIATOR UNIT ASSY (1) Disconnect the board to board. (2) Disconnect the connector wires. (3) Remove the screws. Proceeding:TOP COVER BACK PANEL UNIT ASSY A.VIDEO UNIT, AUDIO UNIT and RADIATOR UNIT ASSY DIGITAL UNIT ASSY v Direction of photograph: C MAIN CPU UNIT CX073CX192 Direction of photogr

40、aph: A A.VIDEO UNIT AUDIO UNIT RADIATOR UNIT ASSY RadioFans.CN 13 AVR-4310CI/AVR-4310/AVC-4310 5. REG UNIT (1) Disconnect the board to board and connector wires. (2) Disconnect the connector wires, then remove the screws. 6. AMP UNIT (1) Disconnect the VH connector and conector. Proceeding:TOP COVER

41、 BACK PANEL UNIT ASSY A.VIDEO UNIT, AUDIO UNIT and RADIATOR UNIT ASSY DIGITAL UNIT ASSY REG UNIT Board to board Direction of photograph: A CX231CX092 v ? ? Direction of photograph: A Proceeding:TOP COVER BACK PANEL UNIT ASSY A.VIDEO UNIT, AUDIO UNIT and RADIATOR UNIT ASSY DIGITAL UNIT ASSY REG UNIT

42、AMP UNIT CX851CX891 CX876 CX874 CX871 CX873 CX872 CX875 CX877 View from bottom RadioFans.CN 14 AVR-4310CI/AVR-4310/AVC-4310 7. P.AMP JOINT UNIT (1) Disconnect the connector. 8. P.AMP UNIT (1) Remove the screws. Proceeding:TOP COVER BACK PANEL UNIT ASSY A.VIDEO UNIT, AUDIO UNIT and RADIATOR UNIT ASSY

43、 DIGITAL UNIT ASSY REG UNIT AMP UNIT P.AMP JOINT UNIT CX803CX805 CX806CX811CX812CX807 CX804 Direction of photograph: A Proceeding:TOP COVER BACK PANEL UNIT ASSY A.VIDEO UNIT, AUDIO UNIT and RADIATOR UNIT ASSY DIGITAL UNIT ASSY REG UNIT AMP UNIT P.AMP JOINT UNIT P.AMP UNIT Direction of photograph: B

44、RadioFans.CN 15 AVR-4310CI/AVR-4310/AVC-4310 SPECIAL MODE Special mode setting button Press the ON/OFF button to turn on while pressing both buttons A and B at the same time. *1 : About RS-232C communications RS-232C communications are not possible when is displayed on the FL display. Press and hold

45、 in the STATUS and buttons for over 3 seconds with the power turned on to turn the display off. RS-232C communications are now enabled. ModeButton AButton Bcontents Version display (com/DSP Error Display) STATUSRETURN Serial No. and firmware versions such as Main, Sub, DSP are displayed in the FL ma

46、nager. Errors are displayed when they occur. (Refer to 16 page.) Displaying the protection history modeSTATUSMENU Displaying the protection history (Refer to 18 page.) Initialization mode (Remove settings for Installer Setup.) STANDARD DSP SIMULATION Backup data initialization is carried out. (Remov

47、e settings for Installer Setup.) Initialization mode (Includes settings for Installer Setup) CURSOR UP CURSOR DOWN Backup data initialization is carried out. (Includes settings for Installer Setup) Mode for switching tuner frequency stepSTANDARD DIRECT/ STEREO -E2 model only- Change tuner frequency

48、step to FM:200kHz/AM:10kHzSTEP. g Mode for preventing remote control acceptance STATUSENTER Operations using remote control are rejected. (Mode cancellation: Turn off power and execute the same button operations as when performing setup.) Panel lock mode DSP SIMULATION ZONE2 Operations using main un

49、it panel buttons or master volume are rejected. Panel lock mode (Remove Master volume) DIRECT/ STEREO ZONE2Operations using main unit panel buttons are rejected. Cancellation of panel lock mode PURE DIRECT ZONE2 Panel lock mode is cancelled. Installer Setup mode*1MENU CURSOR LEFT Access Remote Maintenance mode via the internet.Installer Setup is displayed on GUI/Option Menu. Refer to AVR4310_RemoteMaintenance_.pdf of SDI. ON/OFF RETURN ZONE2 DSP SIMULATION STANDARDSTATUSENTER PURE DIRECT DIRECT/ STEREO MEN