AustralianMonitor-XRS10P-pwr-sm维修电路图 手册.pdf

《AustralianMonitor-XRS10P-pwr-sm维修电路图 手册.pdf》由会员分享，可在线阅读，更多相关《AustralianMonitor-XRS10P-pwr-sm维修电路图 手册.pdf（10页珍藏版）》请在收音机爱好者资料库上搜索。

1、 Australian Monitor 1 Clyde Street, Silverwater NSW 2128 Australia +61 2 9647 1411 .au SERVICE INFORMATION XRS10P POWERED LOUDSPEAKER CONTENTS: OPERATION MANUAL SCHEMATIC DIAGRAM RadioFans.CN XRS SERIES POWERED AND PASSIVE LOUDSPEAKERS INSTALLATION AND OPERATION MANUAL RadioFans.CN 1. Save the carto

2、n and packing material even if the equipment has arrived in good condition. Should you ever need to ship the unit, use only the original factory packing. 2. Read all documentation before operating your equipment. Retain all documentation for future reference. 3. Follow all instructions printed on un

3、it chassis for proper operation. 4. Do not spill water or other liquids into or on the unit, or operate the unit while standing in liquid. 5. Make sure power outlets conform to the power requirements listed on the back of the unit. 6. Do not use the unit if the electrical power cord is frayed or bro

4、ken. The power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords and plugs, convenience receptacles, and the point where they exit from the appliance. 7. Always operate the unit with the AC

5、ground wire connected to the electrical system ground. Precautions should be taken so that the means of grounding of a piece of equipment is not defeated. 8. Mains voltage must be correct and the same as that printed on the rear of the unit. Damage caused by connection to improper AC voltage is not

6、covered by any warranty. 9. Have gain controls on amplifi ers turned down during power-up to prevent speaker damage if there are high signal levels at the inputs. 10 Power down and disconnect units from mains voltage before making connections. 11. Never hold a power switch in the “ON” position if it

7、 wont stay there itself! 12. Do not use the unit near stoves, heat registers, radiators, or other heat producing devices. 13. Do not block fan intake or exhaust ports. Do not operate equipment on a surface or in an environment which may impede the normal fl ow of air around the unit, such as a bed,

8、rug, weathersheet, carpet, or completely enclosed rack. If the unit is used in an extremely dusty or smoky environment, the unit should be periodically “blown free” of foreign matter. 14. Do not remove the cover. Removing the cover will expose you to potentially dangerous voltages. There are no user

9、 serviceable parts inside. 15. Do not drive the inputs with a signal level greater than that required to drive equipment to full output. 16. Do not connect the inputs / outputs of amplifi ers or consoles to any other voltage source, such as a battery, mains source, or power supply, regardless of whe

10、ther the amplifi er or console is turned on or off. 17. Do not run the output of any amplifi er channel back into another channels input. Do not parallel- or series-connect an amplifi er output with any other amplifi er output. Australian Monitor is not responsible for damage to loudspeakers for any

11、 reason. 18. Do not ground any “hot” (red) terminal. Never connect a “hot” (red) output to ground or to another “hot” (red) output! 19. Non-use periods: the power cord of equipment should be unplugged from the outlet when left unused for a long period of time. 20. Service Information Equipment shoul

12、d be serviced by qualifi ed service personnel when: A. The power supply cord or the plug has been damaged. B. Objects have fallen, or liquid has been spilled into the equipment C. The equipment has been exposed to rain D. The equipment does not appear to operate normally, or exhibits a marked change

13、 in performance E. The equipment has been dropped, or the enclosure damaged. THIS SAFETY INFORMATION IS OF A GENERAL NATURE AND MAY BE SUPERSEDED BY INSTRUCTIONS CONTAINED WITHIN THIS MANUAL IMPORTANT SAFETY INFORMATION RadioFans.CN PAGE 3XRS SERIES INSTALLATION AND OPERATION MANUAL Building on the

14、reliability and sonic quality of the very popular XR speaker series, Australian Monitor brings you the AM Pro XRS two way injection moulded speaker enclosures with more features and new aesthetic to suit both live sound reinforcement and permanent installation. From Front of House to fold back, the

15、dance fl oor to background fi ll, the XRS series with both passive and powered options are designed with fl exibility and performance in mind. The AM Pro XRS range includes 8”, 10” and 12” models all with high quality compression drivers and represent a signifi cant advancement in injection moulded

16、box design while maintaining excellent audio quality and great value for money. AUS, EUR, USA REV A 24th Nov 2008 This symbol is intended to alert the user to the presence of uninsulated “dangerous voltage” within the products enclosure that may be of suffi cient magnitude to constitute a risk of el

17、ectric shock to persons. This symbol is intended to alert the user to the presence of important operational and maintenance (servicing) instructions in the literature accompanying the appliance. To prevent electric shock do not use this (polarised) plug with an extension cord, receptacle or other ou

18、tlet unless the blades can be fully inserted to prevent blade exposure. To prevent electric shock, match wide blade of plug to wide slot, fully insert. Caution: CAUTION CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK), NO USER SERVICEABLE PARTS INSIDE, REFER SERVICING TO

19、QUALIFIED SERVICE PERSONNEL. WARNING! TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE. RISK OF ELECTRIC SHOCK DO NOT OPEN INTRODUCTION 3 FRONT AND REAR PASSIVE PANEL 4 REAR POWERED PANEL 5 SPECIFICATIONS 6 INTRODUCTION AND CONTENTS RadioFans.CN PAGE 4XRS

20、 SERIES INSTALLATION AND OPERATION MANUAL FRONT AND REAR PANEL PASSIVE VERSION 1 High Frequecy Driver Horn loaded compression driver. Directivity 90deg x 90deg. Passive crossover in the XRS8/10/12. XRS8/XRS8P 1.5” XRS10/XRS10P 1.5” XRS12/XRS12P 2” Active crossover and power amp in XRS8P/10P/12P. XRS

21、8P 50W XRS10P 50W XRS12P 100W 2 Low Frequency Woofer Driver sizes: XRS8/XRS8P 8” XRS10/XRS10P 10” XRS12/XRS12P 12” Active crossover and power amp in XRS8P/10P/12P. XRS8P 100W XRS10P 100W XRS12P 300W Note that the XRS8 ships as a pair. 1 Speaker Input The input connector is a 4 pole speakon compatibl

22、e connector. Pins 1+ and 1- are wired to the +ve and -ve respectively of the speaker. The XRS10 and XRS12 have 2 connectors. They are wired in parallel so either connector can be used as an input, the other as a loop through. Accessories: XRS8/XRS8P XR8PMA Pole mount adapter XR8UMB Universal mountin

23、g bracket XRS10/XRS10P XR10CVR Heavy duty cover AMISLSB1 Wall mount brackets ATC303 Tripod speaker stand ATC304 Heavy duty tripod speaker stand ATC305 Winch up speaker stand XR10-12UB Universal bracket XRS12/XRS12P XR12CVR Heavy duty cover AMISLSB1 Wall mount brackets ATC303 Tripod speaker stand ATC

24、304 Heavy duty tripod speaker stand ATC305 Winch up speaker stand XR10-12UB Universal bracket 112 XRS8 shown here RadioFans.CN PAGE 5XRS SERIES INSTALLATION AND OPERATION MANUAL REAR PANEL POWERED VERSION 1513 14 101112789246 5 3 1 1 MIC IN This is a balanced XLR microphone input. 2 Mic SIGNAL This

25、is a green LED signal present indicator for the Mic input. It indicates signal present on the input and is not affected by the level control. 3 LINE IN This is a balanced XLR line level input. 4 Line SIGNAL This is a green LED signal present indicator for the Line input. It indicates signal present

26、on the input and is not affected by the level control. 5 LINE OUT The LINE OUT is on an XLR connector. This output can be connected to the LINE IN on another XRS Powered speaker to expand the system. 6 Output CLIP This is a red LED clip indicator for the mixed mic and line audio signal. Some fl ashi

27、ng of red is acceptable on program transients. Continuous fl ashing of red could be placing undue stress on the speaker and will sound distorted. Turn down the input level until the clip LED is no longer lit. 7 Mic LEVEL This controls the level of the MIC input (1). 8 Mic BASS This is the bass contr

28、ol for the MIC input (1). There is 12dB of cut and boost at 100Hz. This EQ is the shelving type. 9 Mic TREBLE This is the treble control for the MIC input (1). There is 10dB of cut and boost at 10kHz. This EQ is the shelving type. 10 Line LEVEL This controls the level of the LINE input. (3) 11 Line

29、BASS This is the bass control for the LINE input (3). There is 12dB of cut and boost at 100Hz. This EQ is the shelving type. 12 Line TREBLE This is the treble control for the LINE input (3). There is 10dB of cut and boost at 10kHz. This EQ is the shelving type. 13 Power Switch This switch turns the

30、power on or off to the unit. 14 IEC Mains Input Socket This is a standard IEC 3 pin socket. It accepts a standard IEC mains cable, (provided). The fuse draw contains the mains fuse and a spare. The mains fuse is a time lag (slow blow) HRC 20mm x 5mm ceramic or glass type fuse. XRS8P XRS10P XRS12P 2.

31、5A 2.5A 5.0A IMPORTANT: Always replace the fuse with one of the same value and type. NOTE: Always disconnect power to the amplifi er before replacing fuses. 15 Voltage Select Switch This switch is used to select the mains voltage for your region. Select either 230V or 115V. IMPORTANT: Disconnect pow

32、er to the amplifi er before operating this switch. IMPORTANT: Make sure this setting is correct before connecting the unit to the mains. RadioFans.CN PAGE 6XRS SERIES INSTALLATION AND OPERATION MANUAL SPECIFICATIONS XRS8P XRS10P XRS12P Drivers 1 x 8” woofer 1 x 10” woofer 1 x 12” woofer 1 x 1.5” HF

33、driver 1 x 1.5” HF driver 1 x 2” HF driver Frequency Response(-3dB) 65Hz-18kHz 55Hz-18kHz 50Hz-18kHz Frequency Response(-10dB) 55Hz-18kHz 50Hz-18kHz 40Hz-20kHz Peak Sound Level(dB 1m) 118dB 121dB 125dB Tone controls Bass control 100Hz 12dB 12dB 12dB Treble control 10kHz 10dB 10dB 10dB Output Power 1

34、00W(low) + 50W(high) 100W(low) + 50W(high) 300W(low) + 100W(high) Distortion (THD) Line 0.02% 0.02% 0.02% Microphone 0.04% 0.04% 0.04% Tweeter Dispersion(HxV) 90 x 90 90 x 90 90 x 90 Input Impedance Line 20kOhm 20kOhm 20kOhm Microphone 10kOhm 10kOhm 10kOhm Connectors XLR 3 XLR 3 XLR 3 Power Supply A

35、C 115V/230V, 50/60Hz AC 115V/230V, 50/60Hz AC 115/230V, 50/60Hz Dimensions(WxDxH) 277 x 265 x 407mm 325 x 308 x 478mm 415 x 391 x 600mm Packing Dimensions(WxDxH) 355 x 325 x 470mm 375 x 355 x 535mm 465 x 435 x 680mm Net Weight 8.6kg 10.5kg 23kg Gross Weight 10.1kg 11.8kg 25.2kg RadioFans.CN PAGE 7XR

36、S SERIES INSTALLATION AND OPERATION MANUAL SPECIFICATIONS XRS8 XRS10 XRS12 Drivers 1 x 8” woofer 1 x 10” woofer 1 x 12” woofer 1 x 1.5” HF driver 1 x 1.5” HF driver 1 x 2” HF driver Frequency Response(-3dB) 65Hz-18kHz 55Hz-18kHz 50Hz-18kHz Frequency Response(-10dB) 60Hz-20kHz 50Hz-20kHz 40Hz-20kHz S

37、ensitivity(dB 1W 1m) 92 dB 95 dB 97 dB Impedance 8 Ohm 8 Ohm 8 Ohm Recommended Max Power(Wrms) 100 W 250 W 300 W Max Sound Level(dB 1m) 118dB 125dB 128dB Dispersion(HxV) 90 x 90 90 x 90 90 x 90 Harmonic Distortion 1% 1% 1% Speakon compatible connectors 1 2 2 Dimensions(WxDxH) 277 x 257 x 400mm 321 x

38、 321 x 464mm 415 x 382 x 620mm Packing Dimensions(WxDxH) 595 x 310 x 460mm 375 x 355 x 535mm 465 x 435 x 680mm Net Weight 6.5kg 10kg 18kg Gross Weight 15kg (pair) 12kg 20kg RadioFans.CN SYDNEY (NSW SALES) 1 Clyde Street Silverwater NSW 2128 Private Bag 149 Silverwater NSW 1811 Phone: (02) 9647 1411

39、Fax: (02) 9648 3698 Email: .au CANBERRA (ACT SALES) 1st Floor, Campion Street Deakin ACT 2600 PO Box 109 Deakin West ACT 2600 Phone: (02) 6260 4544 Fax: (02) 6260 4744 Email: gordon.anderson .au MELBOURNE (VIC & TAS SALES) 22/277 Middleborough Road Box Hill VIC 3128 PO Box 151 Blackburn South VIC 31

40、30 Phone: (03) 9890 7477 Fax: (03) 9890 7977 Email: .au BRISBANE (QLD SALES) 42 Commercial Road Fortitude Valley QLD 4006 PO Box 2578 Fortitude Valley BC QLD 4006 Phone: (07) 3852 1312 Fax: (07) 3252 1237 Email: .au ADELAIDE (SA & NT SALES) 31 Walsh Street Thebarton SA 5031 PO Box 157 Hindmarsh SA 5

41、007 Phone: (08) 8352 4444 Fax: (08) 8352 4488 Email: .au PERTH (WA SALES) 3/11 Howe Street Osborne Park WA 6017 PO Box 1281 Osborne Park BC WA 6916 Phone: (08) 9204 0200 Fax: (08) 9244 3783 Email: .au AUCKLAND (NZ SALES) 9C Piermark Drive Albany 0752 New Zealand PO Box 300-512 Albany 0752 Phone: (09

42、) 415 9426 Fax: (09) 415 9864 Email: nzhillssvl.co.nz AUSTRALIA AND NEW ZEALAND .au EUROPE / ASIA / MIDDLE EAST .au INTERNATIONAL SALES 1 Clyde Street Silverwater NSW 2128 Australia Private Bag 149 Silverwater NSW 1811 Phone: + 61 2 9647 1411 Fax: + 61 2 9748 2537 Email: .au RadioFans.CN 12345678 A

43、B C D 87654321 D C B A R3 30K R4 30K D1 1N4148 D3 1N4148 D2 1N4148 D4 1N4148 +15V +15V -15V -15V C5 22P C6 22P C7 10U/25V-NP C1 10U/25V-NP C3 10U/25V-NP R15 10K C15 22P +15V -15V CV8 100U/50V R9 30K R10 30K D5 1N4148 D7 1N4148 D6 1N4148 D8 1N4148 +15V +15V -15V -15V C12 22P C13 22P C14 10U/25V-NP C8

44、 10U/25V-NP C10 10U/25V-NP 2 3 1 IC2A JRC4560 6 5 7 IC1B JRC4560 2 3 1 IC1A JRC4560 R1 560 R2 560 R7 10K R8 10K C9 47P R16 47 R17 47 C16 10U/25V-NP C17 10U/25V-NP 12 3 CON1 5044 12 3 CON2 5044 12 3 CON3 5040 RP1-1 RP2-1 84 IC3C JRC4560 84 IC1C JRC4560 CV1 104 CV2 104 CV5 104 CV6 104 84 IC2C JRC4560

45、CV3 104 CV4 104 R14 10K R13 10K RP1-3 RP2-3 C2 47P R22 10K OPT1 LCR0202 C22 22P 2 3 1 IC3A JRC4560 R27 100K +15V R23 100K R26 100 R25 3K3 R24 2K2 -15V LED3 RED IN2 Q2 2N5401 Q1 2N5551 C19 10U/25V-NP R18 10K C18 10U/25V-NP R19 10K IN1 6 5 7 IC2B JRC4560 C20 10U/25V-NP R21 10K 6 5 7 IC3B JRC4560 R20 1

46、0K 1 2 3 4 5 CT01 5P*100MM(2.5MM) -15V +15V -15V GND SIN-OUT LIMIT SIN-OUT LIMIT 1 2 3 4 5 6 7 8 9 10 J1A 10PIN2.54mm RP1-1 IN1 +15V -15V 1 2 3 4 5 6 7 8 9 10 J2A 10PIN2.54mm RP2-1 IN2 +15V -15V RP2-3RP1-3 D10 IN4148 LED2 GREE R6 5K1 R29 150K R12 1K5 C11 473 Q4 2N5551 +15V D9 IN4148 LED1 GREE R5 5K1

47、 R28 150K R11 1K5 C4 473 Q3 2N5551 +15V 1 2 3 4 5 6 CT01A 6P*100MM(2.5MM) -15V GND +15V LIMIT SIN-OUT C21 22P R3 10K R1 10K 84 IC4C JRC4560 2 3 1 IC4A JRC4560 R4 15K C1 22P R2 15K RP1-1 R7 15K R8 15K R10 10K R9 1M C4 103 C5 103 C3 472 R5 7K5 R6 7K5 C6 22P RP2 B50K RP3 B50K TREBLE BASS 6 5 7 IC4B JRC

48、4560 CV7 104 CV8 104 RP1-1 OUT1 +15V -15V -15V +15V 1 2 3 4 5 6 7 8 9 10 J1 10PIN2.54mm RP1-3 RP1-3 RP1 A50K AC 1 V+ 2 AC 3 V- 4 BR1 KBU-806 CV23 6800U/50V CV24 6800U/50V CV17 1000U/35V CV18 1000U/35V CV19 220U/25V CV20 220U/25V CV21 104 CV22 104 -15V GND +15V S-IN LIMIT -15V +15V JP1 28V JP2 28V JP

49、3 GND JP7 HIGH+ JP8 HIGH- +15V -15V +35V -35V CV25 470U/50V CV26 470U/50V CV27 104 CV28 104 JP5 LOW+ JP6 LOW- C15 153 C16 153 C17 153 C18 153 C4 123 C5 392 C6 123 C7 392 R26 8K2 R27 6K8 R28 8K2 R29 6K8 R9 15K R10 15K R11 15K R6 10K R3 10K C2 22P C8 1U/50V R12 15K R13 47K D2 1N4148 D1 1N4148 D3 1N4148 R14 10K R15 10K R16 1M R17 1M R18 10K C9 1U/50V R19 2K2 R20 1M +15V R30 5K6 R31 47K D5 1N4148 D4 1N4148 D6 1N4148 R32 10K R33 10K R34 1M R35 1M R36 10K C20 104 R37 2K2 C19 104 +15V D7 1