Yamaha-TSX-100-Service-Manual电路原理图.pdf

《Yamaha-TSX-100-Service-Manual电路原理图.pdf》由会员分享，可在线阅读，更多相关《Yamaha-TSX-100-Service-Manual电路原理图.pdf（40页珍藏版）》请在收音机爱好者资料库上搜索。

1、I CONTENTS TO SERVICE PERSONNEL . 24 PREVENTION OF ELECTROSTATIC DISCHARGE . 5 FRONT PANELS. 67 REAR PANELS . 810 REMOTE CONTROL PANELS. 11 SPECIFICATIONS / 参考仕様. 11 INTERNAL VIEW . 12 DISASSEMBLY PROCEDURES / 分解手順. 1215 TEST MODE . 16 . 17 BLOCK DIAGRAM. 18 WIRING DIAGRAM . 19 PRINTED CIRCUIT BOARD

2、S. 2026 SCHEMATIC DIAGRAMS. 2731 REPLACEMENT PARTS LIST . 3236 REMOTE CONTROL. 3739 101079 SERVICE MANUAL DESKTOP AUDIO SYSTEM 2008 All rights reserved. This manual is copyrighted by YAMAHA and may not be copied or redistributed either in print or electronically without permission. P.O.Box 1, Hamama

3、tsu, Japan 08.03 IMPORTANT NOTICE This manual has been provided for the use of authorized YAMAHA Retailers and their service personnel. It has been assumed that basic service procedures inherent to the industry, and more specifically YAMAHA Products, are already known and understood by the users, an

4、d have therefore not been restated. WARNING:Failure to follow appropriate service and safety procedures when servicing this product may result in personal injury, destruction of expensive components, and failure of the product to perform as specified. For these reasons, we advise all YAMAHA product

5、owners that any service required should be performed by an authorized YAMAHA Retailer or the appointed service representative. IMPORTANT:The presentation or sale of this manual to any individual or firm does not constitute authorization, certification or recognition of any applicable technical capab

6、ilities, or establish a principle-agent relationship of any form. The data provided is believed to be accurate and applicable to the unit(s) indicated on the cover. The research, engineering, and service departments of YAMAHA are continually striving to improve YAMAHA products. Modifications are, th

7、erefore, inevitable and specifications are subject to change without notice or obligation to retrofit. Should any discrepancy appear to exist, please contact the distributors Service Division. WARNING:Static discharges can destroy expensive components. Discharge any static electricity your body may

8、have accumulated by grounding yourself to the ground buss in the unit (heavy gauge black wires connect to this buss). IMPORTANT:Turn the unit OFF during disassembly and part replacement. Recheck all work before you apply power to the unit. TSX-100 TSX-100 2 TSX-100 TSX-100 WALL OUTLET EQUIPMENT UNDE

9、R TEST AC LEAKAGE TESTER OR EQUIVALENT INSULATING TABLE WARNING: CHEMICAL CONTENT NOTICE! This product contains chemicals known to the State of California to cause cancer, or birth defects or other reproductive harm. DO NOT PLACE SOLDER, ELECTRICAL/ELECTRONIC OR PLASTIC COMPONENTS IN YOUR MOUTH FOR

10、ANY REASON WHAT SO EVER! Avoid prolonged, unprotected contact between solder and your skin! When soldering, do not inhale solder fumes or expose eyes to solder/flux vapor! If you come in contact with solder or components located inside the enclosure of this product, wash your hands before handling f

11、ood. 1. Critical Components Information Components having special characteristics are marked s and must be replaced with parts having specifications equal to those originally installed. 2. Leakage Current Measurement (For 120V Models Only) When service has been completed, it is imperative to verify

12、that all exposed conductive surfaces are properly insulated from supply circuits. GMeter impedance should be equivalent to 1500 ohms shunted by 0.15F. GLeakage current must not exceed 0.5mA. GBe sure to test for leakage with the AC plug in both polarities. 本機搭載基板付接合 部無鉛付。 無鉛種類、修理時下記 無鉛使用推奨。 Sn+Ag+Cu

13、 （錫+銀+銅） Sn+Cu （錫+銅） Sn+Zn+Bi （錫+亜鉛+） 注意： 無鉛融点温度通常鉛入比3040 程度高、合 使用。 All of the P.C.B.s installed in this unit and solder joints are soldered using the lead free solder. Among some types of lead free solder currently available, it is recommended to use one of the following types for the repair work.

14、Sn + Ag + Cu (tin + silver + copper) Sn + Cu (tin + copper) Sn + Zn + Bi (tin + zinc + bismuth) Caution: As the melting point temperature of the lead free solder is about 30C to 40C (50F to 70F) higher than that of the lead solder, be sure to use a soldering iron suitable to each solder. About lead

15、free solder / 無鉛 I TO SERVICE PERSONNEL 3 TSX-100 TSX-100 WARNING: Laser Safety This product contains a laser beam component. This component may emit invisible, as well as visible radiation, which may cause eye damage. To protect your eyes and skin from laser radiation, the following precautions mus

16、t be used during servicing of the unit. 1) When testing and/or repairing any component within the product, keep your eyes and skin more than 30 cm away from the laser pick-up unit at all times. Do not stare at the laser beam at any time. 2) Do not attempt to readjust, disassemble or repair the laser

17、 pick-up, unless noted elsewhere in this manual. 3) CAUTION : Use of controls, adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. Laser Emitting conditions: 1) When the top cover is removed, and the STANDBY/ON SW is turned to the “O

18、N” position, the laser component will emit a beam for several seconds to detect if a disc is present. During this time (5-10 sec.) the laser may radiate through the lens of the laser pick-up unit. Do not attempt any servicing during this period! If no disc is detected, the laser will stop emitting t

19、he beam. When a disc is loaded, you will not be exposed to any laser emissions. 2) The laser power level can be adjusted with the VR on the pick-up PWB, however, this level has been set by the factory prior to shipping from the factory. Do not adjust this laser level control unless instruction is pr

20、ovided elsewhere in this manual. Adjustment of this control can increase the laser emission level from the device. CAUTION Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type. WARNING: Lithium batteries 注意 正電池交換爆発起。 同一型名同等品以外電池絶対交換 。 WARNING: Lithium

21、 batteries are dangerous because they can be exploded by improper handling. Observe the following precautions when handling or replacing lithium batteries. Leave lithium battery replacement to qualified service personnel. Always replace with batteries of the same type. When installing on the PC boar

22、d by soldering, solder using the connection terminals provided on the battery cells. Never solder directly to the cells. Perform the soldering as quickly as possible. Never reverse the battery polarities when installing. Do not short the batteries. Do not attempt to recharge these batteries. Do not

23、disassemble the batteries. Never heat batteries or throw them into fire. ADVARSEL! Lithiumbatteri Eksplosionsfare ved fejlagtig hndtering. Udskiftning m kun ske med batteri af samme fabrikat og type. Levr det brugte batteri tilbage til leverandren. VARNING Explosionsfara vid felaktigt batteribyte. A

24、nvnd samma batterityp eller an ekvivalent typ som rekommenderas av apparattillverkaren. Kassera anvnt batteri enligt fabrikantens instruktion. VAROITUS Paristo voi rjht, jos se on virheellisesti asennettu. Vaihda paristo ainoastaan laitevalmistajan suosittelemaan tyyppiin. Hvit kytetty peristo valmi

25、stajan ohjeiden mukaisesti. 4 TSX-100 TSX-100 TypeGaAlAs Wave length780 nm Emission durationcontinuous Warning for power supply The primary side of the power supply carries live mains voltage when the player is connected to the mains even when the player is switched off ! This primary area is not sh

26、ielded so it is possible to touch copper tracks and/or components when servicing the player. Service personnel have to take precautions to prevent touching this area or components in this area. Note: The screws on the DVD mechanism may never be touched, removed or re-adjusted. Handle the DVD mechani

27、sm with care when the unit has to be exchanged! The DVD mechanism is very sensitive for dropping or giving shocks. Laser Diode Properties Laser outputmax. 44.6 W * *This output is the value mea- sured at a distance of about 200 mm (7.9 in) from the ob- jective lens surface on the optical pick-up blo

28、ck. 5 TSX-100 TSX-100 I PREVENTION OF ELECTROSTATIC DISCHARGE Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are called Electrostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field-effe

29、ct transis- tors and semiconductor “chip” components. The following techniques should be used to help reduce the incidence of compo- nent damage caused by electro static discharge (ESD). 1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any ESD

30、on your body by touching a known earth ground. Alternatively, obtain and wear a commercially available discharging ESD wrist strap, which should be removed for potential shock reasons prior to applying power to the unit under test. 2. After removing an electrical assembly equipped with ES devices, p

31、lace the assembly on a conductive surface such as aluminum foil, to prevent electrostatic charge buildup or exposure of the assembly. 3. Use only a grounded-tip soldering iron to solder or unsolder ES devices. 4. Use only an anti-static solder removal device. Some solder removal devices not classifi

32、ed as “anti-static (ESD protected)” can generate electrical charge sufficient to damage ES devices. 5. Do not use freon-propelled chemicals. These can generate electrical charges sufficient to damage ES devices. 6. Do not remove a replacement ES device from its protective package until immediately b

33、efore you are ready to install it. (Most replacement ES devices are packaged with leads electrically shorted together by conductive foam, aluminum foil or compa- rable conductive material). 7. Immediately before removing the protective material from the leads of a replacement ES divice, touch the pr

34、otective mate- rial to the chassis or circuit assembly into which the device will be installed. CAUTION: Be sure no power is applied to the chassis or circuit, and observe all other safety precautions. 8. Minimize bodily motions when handling unpackaged replacement ES devices. (Otherwise harmless mo

35、tion such as brush- ing together of your fabric clothes or lifting of your foot from a carpeted floor can generate static electricity (ESD) sufficient to damage an ES device). Grounding for electrostatic breakdown prevention 1. Human body grounding. Use the antistatic wrist strap to discharge the st

36、atic electricity from your body. 2. Work table grounding. Put a conductive material (sheet) or steel sheet on the area where the optical pickup is placed and ground the sheet. Caution: The static electricity of your clothes will not be grounded through the wrist strap. So take care not to let your c

37、lothes touch the optical pickup. 1M-ohms Conductive material (sheet) or steel sheet Anti-static wrist strap 6 TSX-100 TSX-100 iPod port USB port I FRONT PANELS Top view R, B, G models U, A, J models 7 TSX-100 TSX-100 R, A, G, J models B model U model Front view 8 TSX-100 TSX-100 B model I REAR PANEL

38、S Rear view U model R, A, G, J models PHONESPORTABLE 9 TSX-100 TSX-100 Bottom view U model R model 10 TSX-100 TSX-100 J model A, B, G models TSX-100 11 Silver color I Player Section / 部 Playback system / 再生 . CD, CD-R/RW I Amplifier Section / 部 Type / 形式 .Twin SR-Bass Magnetic shielding type / 防磁型 D

39、river / .4.5 cm (1-3/4) Titanium cone full-range x 2 Minimum RMS output power per channel / 定格出力 (EIAJ) .10 W + 10 W Input sensitivity/Impedance / 入力感度/ U, R, A, B, J models PORTABLE . 300 mV/47 k-ohms G model AUX . 300 mV/47 k-ohms Output level/Impedance / 出力/ PHONES (volume max.) U, R, A, G models

40、 . 1 V/32 ohms B, J models . 470 V/32 ohms I iPod Section / iPod部 U, A, J models Support iPod models / 対応iPod . iPod (Click and wheel), iPod mini, iPod nano, iPod touch I FM Tuner Section / FM部 Tuning range / 受信周波数範囲 U model. 87.5 to 107.9 MHz R, A, B, G models . 87.50 to 108.00 MHz J model . 76.0 t

41、o 108.0 MHz I AM Tuner Section / AM部 Tuning range / 受信周波数範囲 U model. 530 to 1,710 kHz R, A, B, G, J models . 522 to 1,629 kHz I DAB Tuner Section B model Tuning range (BAND III). 174 MHz to 240 MHz Sensitivity. -95 dB Selectivity (for adjacent channel). 40 dB Antenna input (unbalanced) . 50 ohms I G

42、eneral / 総合 Power supply / 電源電圧 U model .AC 120 V, 60 Hz R, A, B, G, J models. AC 100-240 V, 50/60 Hz Power consumption / 消費電力 . 20 W Standby power consumption / 待機時消費電力 . 1.0 W or less Dimensions (W x H x D) / 寸法 （幅高奥行） . 300 x 141.5 x 200 mm (11-13/16” x 5-9/16” x 7-7/8”) Weight / 質量 . 2.7 kg (5 lbs. 15 oz.) Finish / 仕上 Black color . U, R, A, B, G, J models Silver color . U, R, A, B, G, J models Accessories / 付属品 Remote control x 1, Battery (Lithium, CR2025) x 1, AM loop antenna (2.0 m) x 1, Indoor FM antenna (1.5 m) x 1, Power cable (2 m) x 1, Indoor DAB