Yamaha-PMTH-35-Service-Manual电路原理图.pdf

《Yamaha-PMTH-35-Service-Manual电路原理图.pdf》由会员分享，可在线阅读，更多相关《Yamaha-PMTH-35-Service-Manual电路原理图.pdf（6页珍藏版）》请在收音机爱好者资料库上搜索。

1、SERVICE MANUAL 100864 SERVICE MANUAL PMT-L31/PMT-H35 CEILING MOUNT BRACKET G PMT-L31 PMT-L31/PMT-H35 G PMT-H35 Tilt angle adjustment screws (There are also screws on the opposite side.) Height locking screw Ceiling bracket Projector mounting adapter Horizontal angle adjustment screw (four in total)

2、Height adjustment pole 取付 傾角度調整 （反対側。） Vertical angle adjustment screws (There are also screws on the opposite side.) 上下角度調整 （反対側。） Mounting guide pin 取付 左右角度調整（計4所） 高固定 高調整 天井固定金具 Projector mounting adapter Tilt angle adjustment screws (There are also screws on the opposite side.) Vertical angle ad

3、justment screws (There are also screws on the opposite side.) Ceiling bracket 天井固定金具 Horizontal angle adjustment screws / 左右角度調整 Mounting guide pin 取付 上下角度調整 （反対側。） 取付 傾角度調整 （反対側。） RadioFans.CN 收音机爱 好者资料库 PMT-L31/PMT-H35 PMT-L31/PMT-H35 2 IDIMENSIONS OF PARTS / 各部寸法 with the DPX-1000 installed PMT-H

4、35 with the DPX-1000 installed 10 mm (3/8 inch) 30 mm 8.8 mm (3/16 inch) (fully penetrating holes) 844 to 1414 mm (33-3/16 to 55-11/16 inch) 787 to 1357 mm (30-15/16 to 53-3/8 inch) 963 to 1533 mm (37-7/8 to 60-3/8 inch) 184.5 mm (7-5/16 inch) (1-3/16 inch) 495 mm (19-1/2 inch) PMT-L31 10 x 13 mm (3

5、/8 x 1/2 inch) (elliptical hole) 10 mm (3/8 inch) (hole)9 mm (3/8 inch) (hole) 9 x 13 mm (3/8 x 1/2 inch) (elliptical hole) 10 10 196 mm 170 mm 140 mm 120 mm 156 mm 226 mm 162 mm 176 mm 236 mm (7-3/4 inch) (6-11/16 inch) (5-1/2 inch) (4-3/4 inch) (6-1/8 inch) 10 mm (3/8 inch) (hole) 9 mm (3/8 inch)

6、(hole) (8-7/8 inch) (6-3/8 inch) (6-13/16 inch) (9-5/16 inch) 14.5 mm (5/8 inch) 297.4 mm (11-3/4 inch) 17 mm (3/4 inch) 13 mm (1/2 inch) 382 mm (15 inch) 360 mm (14-3/16 inch) 124 mm (4-7/8 inch) 155 mm (6-1/8 inch) 258 mm (10-3/16 inch) 82 mm (3-3/16 inch) 139 mm (5-1/2 inch) 10 10 184.5 mm (7-5/1

7、6 inch) 495 mm (19-1/2 inch) Projection direction 120 mm (4-3/4 inch) 200 mm (8-7/8 inch) 210 mm 140 mm (8-5/16 inch) (5-1/2 inch) Projection direction 10 x 13 mm (3/8 x 1/2 inch) (elliptical hole) Front View /正面図 Projector mounting adapter 取付 Front View /正面図 DPX-1000取付時 DPX-1000取付時 Top View /上面図Top

8、 View /上面図 投影方向 投影方向 RadioFans.CN 收音机爱 好者资料库 PMT-L31/PMT-H35 PMT-L31/PMT-H35 3 Ref. N o.PART N O.DescriptionRemarksMarkets部品名 Rank New Part s (新規部品) * 1AAX30700SAFTY BRACKETSPCC t2.0 2pcs/setPMTL11-X7安全金具 * 2AAX45760SAFTY WIRESUS304 2pcs/setPMTL31-X2落下防止用 * 3AAX45750PAN HEAD SCREW6x20 N I 4pcs/setPM

9、TL31-X3小 4AAX30720HEXAGON BOLT6x16 N I 4pcs/setPMTL11-X8六角 5AAX30680PAN HEAD SCREW4x10 N I 8pcs/setPMTL11-X10小 6AAX30670PAN HEAD SCREW5x10 N I 4pcs/setPMTH15-X7小 IPACKING LIST / 同梱部品一覧 PMT-L31 Ceiling bracket x 1 PMT-H35 Ceiling bracket x 1 Common parts (The following parts are provided with each br

10、acket.) Projector mounting adapter x 1Projector mounting screws (M6, pan head) x 4 Adjustment pole locking screws (M5) x 4 Safety brackets x 2 Safety wires x 2 Vertical angle adjustment screws (M6, hexagonal head) x 4 Safety bracket mounting screws (M4, pan head) x 4 Safety wire mounting screws (M4,

11、 pan head) x 4 Installation Manual x 1 天井固定金具 x 1個天井固定金具 x 1個 調整固定(M5) x 4本 共通部品(両方一組同梱。) 取付 x 1個 安全金具 x 2個 落下防止用 x 2本 取付(M6、) x 4本 安全金具取付(M4、) x 4本 落下防止用取付(M4、) x 4本 上下角度調整(M6、六角頭) x 4本 設置調整説明書 x 1冊 2 1 4 3 5 5 6 4 PMT-L31/PMT-H35 PMT-L31/PMT-H35 IREMOVING THE PROJECTOR / 取外方 1 Remove the vertical

12、angle adjustment screws. Remove the four vertical angle adjustment screws (M6, hexagonal head), two on the right and left sides respectively. 2 Remove the safety brackets. Remove the four safety bracket mounting screws (M4, pan head), two on the right and left sides respectively, and the safety brac

13、kets can be removed. 1 上下角度調整外 上下角度調整(M6 、 六角頭)4 本外(左右 2 所)。 2 安全金具取外 安全金具取付(M4 、)4 本外、安全 金具取外(左右2 所)。 (PMT-L31) Vertical angle adjustment screw (Hand-tighten the other side also.) Projection direction 上下角度調整 （反対側。） 投影方向 Safety bracket mounting screw (M4, pan head) 安全金具取付(M4、) 安全金具 (PMT-L31) Safety

14、bracket 5 PMT-L31/PMT-H35 PMT-L31/PMT-H35 3 Remove the projector from the ceiling bracket. As shown by the arrow in the figure, lift the projector di-agonally first and then pull it down. (The mounting guide pin of the ceiling bracket comes off from the groove in the projector mounting adapter.) 4 R

15、emove the safety wires. Remove the four safety wire mounting screws (M4, pan head), two on the right and left sides respectively. Loosen the band to make the loop of the safety wire larger. Re-move the safety wire from the adjuster of the projector. 3 天井固定金具取外 図矢印斜上持上 下引抜。 （取付溝天井固 定金具取付抜） 4 落下防止用取外

16、落下防止用取付(M4 、)4 本 外。 (左右2 所)。 結束引上、落下防止用輪 大。 落下防止用 取外。 (PMT-L31) Projection direction Mounting guide pin 取付 Projector mounting adapter 取付 投影方向 落下防止用 落下防止用取付 (M4、) 取付 結束 Safety wire mounting screws (M4, pan head) Projector mounting adapter Band Safety wire 6 PMT-L31/PMT-H35 PMT-L31/PMT-H35 5 Remove th

17、e projector mounting adapter from the projector. Remove the four projector mounting screws (M6, pan head). The mounting adapter can then be removed. 5 取付 取外 取付(M6 、 )4 本外、 取付取外。 Projector mounting screws (M6, pan head) 取付 取付(M6、) 底面 Projector mounting adapter Bottom of the projector ISPECIFICATIONS

18、/ 参考仕様 Product Name /Ceiling Mount Bracket / Model No. /PMT-L31PMT-H35 Height / 844 to 1414 mm (33-3/16 to 55-11/16 inch) (variable in 30 mm (1-3/16-inch) steps) Vertical angle / 15 15 Horizontal angle / 1010 Tilt angle / 1010 Dimensions of ceiling bracket 236 x 226 x 799 to 1369 mm (9-15/16 x 8-7/8

19、 x 31-1/2 to 53-15/16 inch) (Height is variable in 30-mm (1-3/16-inch) steps) Dimensions of adapter (W x D x H) (W x D x H) Weight /3.0 kg (6 lbs 10 oz)6.2 kg (13 lbs 11 oz) * Specifications are subject to change without notice. 382 x 327.2 x 81.2 mm (15 x 12-7/8 x 3-3/16 inch) Adjustment range 139 mm (5-1/2 inch) (fixed) 160 x 196 x 94 mm (6-5/16 x 7-3/4 x 3-11/16 inch) 品名 型番 天吊金具 高 上下角度 左右角度 傾角度 / 調整幅 / 天井固定金具外形寸法 / 外形寸法 質量