Yamaha-MSR-100-Service-Manual电路原理图.pdf

《Yamaha-MSR-100-Service-Manual电路原理图.pdf》由会员分享，可在线阅读，更多相关《Yamaha-MSR-100-Service-Manual电路原理图.pdf（32页珍藏版）》请在收音机爱好者资料库上搜索。

1、0.166K-7304 Printed in Japan 02.1120021201-56000 SERVICE MANUAL PA 011662 HAMAMATSU, JAPAN CONTENTS SPECIFICATIONS. 3 PERFORMANCE GRAPH. 4 PANEL LAYOUT. 4 CIRCUIT BOARD LAYOUT. 5 DIMENSIONS. 5 LEVEL DIAGRAM. 6 DISASSEMBLY PROCEDURE. 7 IC BLOCK DIAGRAM. 12 CIRCUIT BOARDS. 12 INSPECTIONS. 17 BLOCK DIA

2、GRAM CIRCUIT DIAGRAM PARTS LIST MSR100/SMS100 POWERED SPEAKER This document is printed on chlorine free (ECF) paper. MSR100 （目次） （総合仕様） （特性図） （） （） （寸法図） （） （分解手順） （IC図） （基板図） （検査） （） （回路図） （ECF：無塩素系漂白）使用。 RadioFans.CN 收音机爱 好者资料库 MSR100/SMS100 2 IMPORTANT NOTICE This manual has been provided for the

3、 use of authorized Yamaha Retailers and their service personnel. It has been assumed that basic service procedures inherent to the industry, and more specifically Yamaha Products, are already known and under- stood by the users, and have therefore not been restated. WARNING :Failure to follow approp

4、riate service and safety procedures when servicing this product may result in per- sonal injury, destruction of expensive components and failure of the product to perform as specified. For these reasons, we advise all Yamaha product owners that all service required should be performed by an authoriz

5、ed Yamaha Retailer or the appointed service representative. IMPORTANT :This presentation or sale of this manual to any individual or firm does not constitute authorization certifi- cation, recognition of any applicable technical capabilities, or establish a principal-agent relationship of any form.

6、The data provided is belived to be accurate and applicable to the unit(s) indicated on the cover. The research engineering, and service departments of Yamaha are continually striving to improve Yamaha products. Modifications are, therefore, inevitable and changes in specification are subject to chan

7、ge without notice or obligation to retrofit. Should any discrepancy appear to exist, please contact the distributors Service Division. WARNING :Static discharges can destroy expensive components. Discharge any static electricity your body may have accumulated by grounding yourself to the ground bus

8、in the unit (heavy gauge black wires connect to this bus.) IMPORTANT :Turn the unit OFF during disassembly and parts replacement. Recheck all work before you apply power to the unit. WARNING: CHEMICAL CONTENT NOTICE! The solder used in the production of this product contains LEAD. In addition, other

9、 electrical/electronic and/or plastic (Where applicable) components may also contain traces of chemicals found by the California Health and Welfare Agency (and possibly other entities) to cause cancer and/or birth defects or other reproductive harm. DO NOT PLACE SOLDER, ELECTRICAL/ELECTRONIC OR PLAS

10、TIC COMPONENTS IN YOUR MOUTH FOR ANY REASON WHAT SO EVER! Avoid prolonged, unprotected contact between solder and your skin! When soldering, do not inhale solder fumes or expose eyes to solder/flux vapor! If you come in contact with solder or components located inside the enclosure of this product,

11、wash your hands before handling food. WARNING Components having special characteristics are marked and must be replaced with parts having specification equal to those originally installed. WARNING: THIS APPARATUS MUST BE EARTHED IMPORTANT THE WIRES IN THIS MAINS LEAD ARE COLOURED IN ACCORDANCE WITH

12、THE FOLLOWING CODE: GREEN-AND-YELLOW : EARTH BLUE : NEUTRAL BROWN : LIVE As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows: The wire which is coloured GREEN and YELLOW must be conne

13、cted to the terminal in the plug which is marked by the letter E or by the safety earth symbol or coloured GREEN and YELLOW. The wire which is coloured BLUE must be connected to the terminal which is marked with the letter N or coloured BLACK. The wire which is coloured BROWN must be connected to th

14、e terminal which is marked with the letter L or coloured RED. * This applies only to products distributed by YAMAHA KEMBLE MUSIC (U.K.) LTD. 印商品、安全維持重要部品。交換場合、安全必指定部品使用下。 RadioFans.CN 收音机爱 好者资料库 MSR100/SMS100 3 SPECIFICATIONS General specifi cations Type 2way Bass Refl ex Powered Speaker Speaker Uni

15、t LF: 200 mm Cone HF: 25.4 mm Compression Driver Frequency Range.55 Hz20 kHz (10 dB) Cross Over Frequency.4 kHz Maximum Output Level.112 dB (1 m) Dimension (WHD).275 455.5 255 mm Weight.11 kg Color.Black (Approximate Munsell Value 5 PB2/1) Accessories.Power supply cord 2.5 m (AC Inlet type) Option .

16、BWS50-190/260/320, BCS251, BBS251 Amp. Unit Max Power.100W at 1 kHz, THD=1%, RL=6 Input Sensitivity.INPUT 1: 50 dB* (MIC), +4 dB* (LINE) INPUT 2, 3: 10 dB* Input Impedance.INPUT 1, 2, 3: 10 k Output Sensitivity.LINK OUT: 10 dB* Output Impedance.LINK OUT: 10 k Controls LEVEL Control.INPUT 1, 2, 3, MA

17、STER EQ Control.LOW: 3 dB at 60 Hz HIGH: 6 dB at 10 kHz POWER Switch.ON/OFF Connectors INPUT 1.XLR-3-31 (balanced) INPUT 2, 3.Phone (unbalanced) LINK OUT.Phone (unbalanced) Indicator POWER Indicator.Green LED CLIP Indicator.Red LED Power Requirement USA and Canada.AC 120 V, 60 Hz Europe.AC 230 V, 50

18、 Hz Australia.AC 240 V, 50 Hz Korea.AC 220 V, 60 Hz Power Consumption.70 W * 0 dB=0.775 V For European Model Purchaser/User Information specifi ed in EN55103-1 and EN55103-2. Inrush Current: 10A Conformed Environment: E1, E2, E3 and E4 総合仕様 総合仕様 形式 型 LF: 200mm HF: 25.4mm 再生周波数帯域.55Hz 20kHz(-10dB) 周波

19、数.4kHz 最大出力音圧 .112dB （軸上 1m） 最大外形寸法（ W H D） .275 455.5 255mm 質量.11kg 色 .黒（近似値 5PB2/1） 付属品.電源（AC 型、2.5m） .BWS50-190/260/320、 BCS251、BBS251 部 定格最大出力 .100W at 1kHz、THD=1%、 RL=6 入力感度 .INPUT 1:-50dB*（MIC）、 +4dB*（LINE） INPUT 2、3: -10dB* 入力.INPUT1、2、3: 10k 出力感度.LINK OUT: -10dB* 出力.LINK OUT: 10k LEVEL.INPUT

20、1、2、3、MASTER EQ.LOW: 3dB at 60Hz HIGH: 6dB at 10kHz POWER.ON/OFF INPUT1.XLR-3-31（型） INPUT2、3. （型） LINK OUT. （型） POWER.緑色発光LED CLIP.赤色発光LED 電源.AC100V、50/60Hz 消費電力.65W *0dB=0.775V MSR100/SMS100 4 POWER Switch INPUT1 Connector Sensitivity Switch INPUT2 and INPUT3 Connectors LEVEL Controls EQ Controls L

21、INK OUT Connector MASTER LEVEL Control CLIP Indicator POWER Indicator AC IN Connector Rear Panel PERFORMANCE GRAPH PANEL LAYOUT 10k1k10020 FREQUENCY (Hz) RESPONSE (dB) -40 -30 -20 -10 0 +10 1 2 3 4 5 6 7 8 9 10 11 （） （電源 ） （入力1 端子） （感度切換） （入力2 端子、入力3 端子） （音量 ） （音質 ） （出力 端子） （全体音量 ） （ ） （電源 ） （電源入力 端

22、子） （） （特性図） MSR100/SMS100 5 DIMENSIONS Units: mm CIRCUIT BOARD LAYOUT 455.5 137 275255 120 2-M8x25 * LOW HIGH 100 (-10dB) E PS SER.NO. MADE IN CHINA 100V 65W 50/60Hz MODEL MSR100 POWERED SPEAKER MASTERMASTER LINK OUTEQ INPUT ON/OFF AC IN POWER POWER CLIP (-10dB) LINE (-10dB) LINE LINE(+4dB) MIC(-50d

23、B) 3 LEVEL +3-3 +6-6 100 LEVEL 100 LEVEL 2 1 010 LEVEL 1 3 2 NEUTRIK Power transformer （電源） Power transformer Right side view Rear view （電源） Power amplifier assembly （Assy） Power amplifier assembly （Assy） NETWORK NETWORK POWER AMPLIFIER POWER AMPLIFIER POWER SWITCH EQ AC AC IN POWER SWITCH EQ IN （寸法

24、図） ( 単位) （） MSR100/SMS100 6 LEVEL DIAGRAM OUTPUT (10dBu) INPUT1 INPUT2, 3 (LINE) 0dBu +4dBu -10dBu -50dBu -4.7dBu -2.2dBu +29.9dBu (SP OUT) INPUT1 (MIC) INPUT3 (10dBu) INPUT2 (10dBu) INPUT1 (50dBu/+4dBu) MIC LINE LF HF 6 100W NW MASTER LEVEL EQ HIGHLOW LOW CUT LOW BOOSTP.AMP （） MSR100/SMS100 7 DISAS

25、SEMBLY PROCEDURE 1.Front Grille Assembly (Time required: About 1 minute) 1-1Remove the four (4) screws marked 100A. The front grille assembly can then be removed. (Fig.1) 2.Speaker LF (Woofer) (Time required: About 2 minutes) 2-1Remove the front grille assembly. (See procedure 1.) 2-2Remove the four

26、 (4) screws marked 80. The speaker LF (Woofer) can then be removed. (Fig.1) 2-3Remove the wire LF (red/black) installed to the speaker LF (Woofer). (Photo.1) 3.Front Cabinet Unit and Rear Cabinet Unit (Time required: About 3 minutes) 3-1Remove the front grille assembly. (See procedure 1.) 3-2Remove

27、the speaker LF (Woofer). (See procedure 2.) 3-3Remove the five (5) screws marked 50A and the four (4) screws marked 50B. The front cabinet unit and the rear cabinet unit can then be divided. (Fig.1, 2) Take care not to damage the speaker HF (Tweeter) terminal when opening the front cabinet unit and

28、the rear cabinet unit. 1. Assy (所要時間：約1 分) 1-1100A4 本外、 Assy 外。 (図1) 2. LF() (所要時間：約2 分) 2-1Assy 外。 (1 項参照) 2-2804本外、 LF() 外。 (図1) 2-3 LF()取付束 線LF(赤黒)外。 (写真1) 3.部、 部 (所要時間：約3 分) 3-1Assy 外。 (1 項参照) 3-2LF()外。 (2項参照) 3-350A5本50B4本外、 部部別 。 (図1, 2) 部部開 、 HF （） 端子傷 注意下。 Fig.1 50A:Bind Head Tapping Screw-A

29、 5.0X35 BL (AAX42210) 80:Bind Head Tapping Screw-B 4.0X18 BL (AAX42230) 100A: Bind Head Tapping Screw-B 4.0X10 BL (AAX12100) (図2) 50B:Bind Head Tapping Screw-A 5.0X35 BL (AAX42210) * LOW HIGH 100 (-10dB) E PS SER.NO. MADE IN CHINA 100V 65W 50/60Hz MODEL MSR100 POWERED SPEAKER MASTERMASTER LINK OUTEQ

30、 INPUT ON/OFF AC IN POWER POWER CLIP (-10dB) LINE (-10dB) LINE LINE(+4dB) MIC(-50dB) 3 LEVEL +3-3 +6-6 100 LEVEL 100 LEVEL 2 1 010 LEVEL 1 3 2 NEUTRIK 100A 100A 50A 50A 50B50B 50B 50B 50A 80 100A 50A 80 80 100A 50A 80 Front cabinet unit Speaker LF (Woofer) (部) (LF () Front grille assembly (Assy) Fro

31、nt view Rear view Rear cabinet unit (部) (束線LF (黒) (LF ()(束線LF (赤) Speaker LF (Woofer) Wire LF (Black) Wire LF (Red) Photo.1 (写真1) （分解手順） (A) (B) (B) (図1) Fig.2 (A) MSR100/SMS100 8 4.Speaker HF (Tweeter) (Time required: About 3 minutes) 4-1Remove the front grille assembly. (See procedure 1.) 4-2Divid

32、e the front cabinet unit and the rear cabinet unit. (See procedure 3.) 4-3Remove the wire HF (yellow/blue) installed to the speaker HF (Tweeter). (Photo.2) 4-4Remove the two (2) screws marked 46. The speaker HF (Tweeter) can then be removed from the front cabinet unit. (Fig.3) 5.Network Assembly and

33、 NETWORK Circuit Board (Time required: About 4 minutes) 5-1Remove the front grille assembly. (See procedure 1.) 5-2Divide the front cabinet unit and the rear cabinet unit. (See procedure 3.) 5-3Remove the four (4) screws marked 10e. The network assembly can then be removed from the rear cabinet unit

34、. (Fig.4) 5-4Remove the four (4) screws marked N40. The network holders C and D can then be removed from the NETWORK circuit board. (Fig.4) Remove the P1, P2 connector assembly soldered to the NETWORK circuit board. 4.HF() (所要時間：約3分) 4-1Assy 外。 (1項参照) 4-2部部別 。 (3項参照) 4-3HF()取付束 線HF(黄青)外。 (写真2) 4-446

35、2本外、 部 HF()外。 (図3) 5.Assy、 (所要時間：約4 分) 5-1Assy 外。 (1項参照) 5-2部部別 。 (3項参照) 5-310e4本外、 部 Assy 外。 (図 4) 5-4N404本外、 固定金具 C、D外。 (図4) 取付線材P1、 P2半田外、外。 46: Bind Head Tapping Screw-B 4.0X20 BL (AAX42200) Fig.3 Fig.4 10e:Bind Head Tapping Screw-B 3.0X10 BL (AAX10840) N40:Cup Screw-B PW3.0X8 Y (AAX43390) 46 Fr

36、ont Cabinet Unit (部) Speaker HF (Tweeter) (HF () Network assembly （Assy) Network holder D （固定金具D) Network holder C （固定金具C) N40 10e Rear Cabinet Unit (部) NETWORK (束線HF (黄) (HF () (束線HF (青) Speaker HF (Tweeter) Wire HF (Yellow) Wire HF (Blue) Photo.2 (B) (図3) (B) (B) (図4) (写真2) MSR100/SMS100 9 6.Ampli

37、fier Assembly (Time required: About 1 minute) 6-1Remove the ten (10) screws marked 30. The amplifier assembly can then be removed. (Fig.5) 7.EQ Circuit Board, IN PCB Assembly and IN Circuit Board (Time required: About 3 minutes each) 7-1Remove the amplifier assembly. (See procedure 6.) 7-2Remove the

38、 eight (8) screws marked 210. The shield case assembly can then be removed. (Fig.5, Photo.3) 7-3EQ Circuit Board: 7-3-1Remove the six (6) knobs marked 110 and the six (6) hexagonal nuts marked A. The EQ circuit board can then be removed. (Fig.5, Photo.3) 7-4IN PCB Assembly and IN Circuit Board: 7-4-

39、1Remove the three (3) hexagonal nuts marked 130 and the three (3) screws marked 160. The IN PCB assembly can then be removed. (Fig.5, Photo.3) 7-4-2Remove the screw marked 150c. The angle L can then be removed from the IN circuit board. (Fig.6) 6.Assy (所要時間：約1分) 6-13010本外、 Assy外。 (図5) 7.EQ 、IN Assy、

40、IN (所要時間：各約3分) 7-1Assy 外。 (6 項参照) 7-22108本外、Assy 外。 (図5, 写真3) 7-3EQ: 7-3-1110 6 個A六角 6 個外、 EQ 外。 (図5, 写真3) 7-4IN Assy、IN: 7-4-1130特殊六角 3個160 3本外 、IN Assy 外。 (図5, 写真3) 7-4-2150c1本外、INL金具 外。 (図6) 20:Bonding Tapping Screw-B 4.0X8 BL BO (AAX43620) 30:Bind Head Tapping Screw-B4.0X14 BL (AAX42170) 100B: B

41、onding Tapping Screw-B 3.0X10 BL BO (AAX12110) 130:Hexagonal Nut M12.0 BL 160:Bonding Tapping Screw-B3.0X10 BL BO (AAX12110) 180:Pan Head Tapping Screw-B 3.0X12 BL (AAX43370) 210:Bonding Tapping Screw-B 3.0X10 BL BO (AAX12110) A:Hexagonal Nut Washer Fig.5 * LOW HIGH 100 (-10dB) E PS SER.NO. MADE IN

42、CHINA 100V 65W 50/60Hz MODEL MSR100 POWERED SPEAKER MASTERMASTER LINK OUTEQ INPUT ON/OFF AC IN POWER POWER CLIP (-10dB) LINE (-10dB) LINE LINE(+4dB) MIC(-50dB) 3 LEVEL +3-3 +6-6 100 LEVEL 100 LEVEL 2 1 010 LEVEL 1 3 2 NEUTRIK 30 30 30 30 30 30 130 x 3 110 x 6 210 x 830 A x 6 160 x 2 160 100B x 2 30

43、30 30 180 x 8 20 20 Power transformer (電源) Power amplifier assembly (Assy) Shield case assembly (Assy) Amplifier assembly (Assy) Push knob () Rear view AC IN EQ POWER SWITCH POWER AMPLIFIER (図5) (B) (B) (B) (B) (B) (B) (六角) (特殊六角) () MSR100/SMS100 10 8.Power Amplifier Assembly and POWER AMPLIFIER Ci

44、rcuit Board (Time required: About 4 minutes) 8-1Remove the amplifier assembly. (See procedure 6.) 8-2Remove the shield case assembly. (See procedure 7-2.) 8-3Remove the eight (8) screws marked 180. The power amplifier assembly can then be removed. (Fig.5, Photo.3) 8-4Remove the screw marked P40, the five (5) screws marked P80 and the four (4) screws marked P90. The POWER AMPLIFIER circuit board can then be removed. (Fig.7) Power switch assembly (電源Assy) Power transfor