Yamaha-EMX-3000-Service-Manual电路原理图.pdf
《Yamaha-EMX-3000-Service-Manual电路原理图.pdf》由会员分享,可在线阅读,更多相关《Yamaha-EMX-3000-Service-Manual电路原理图.pdf(82页珍藏版)》请在收音机爱好者资料库上搜索。
1、EMX3000 1 SERVICE MANUAL PA 011569 20010501-135000 1.389K-0221 Printed in Japan 2001.4 HAMAMATSU, JAPAN CONTENTS This document is printed on chlorine free (ECF) paper with soy ink. SPECIFICATIONS. 3/5 PANEL LAYOUT. 7 CIRCUIT BOARD LAYOUT. 10 WIRING. 11 DIMENSIONS. 11 BLOCK & LEVEL DIAGRAM.12 DISASSE
2、MBLY PROCEDURE. 14 LSI PIN DESCRIPTION. 17 IC BLOCK DIAGRAM. 19 CIRCUIT BOARDS. 20 INSPECTIONS. 27/33 CIRCUIT DIAGRAMS.C1 PARTS LIST POWERED MIXER RadioFans.CN 收音机爱 好者资料库 EMX3000 2 WARNING: THIS APPARATUS MUST BE EARTHED IMPORTANT THE WIRES IN THIS MAINS LEAD ARE COLOURED IN ACCORDANCE WITH THE FOLL
3、OWING CODE: GREEN-AND-YELLOW : EARTH BLUE : NEUTRAL BROWN : LIVE As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows: The wire which is coloured GREEN and YELLOW must be connected to
4、the terminal in the plug which is marked by the letter E or by the safety earth symbol or coloured GREEN and YELLOW. The wire which is coloured BLUE must be connected to the terminal which is marked with the letter N or coloured BLACK. The wire which is coloured BROWN must be connected to the termin
5、al which is marked with the letter L or coloured RED. * This applies only to products distributed by YAMAHA KEMBLE MUSIC (U.K.) LTD. WARNING Components having special characteristics are marked and must be replaced with parts having specification equal to those originally installed. IMPORTANT NOTICE
6、 This manual has been provided for the use of authorized Yamaha Retailers and their service personnel. It has been assumed that basic service procedures inherent to the industry, and more specifically Yamaha Products, are already known and under- stood by the users, and have therefore not been resta
7、ted. WARNING :Failure to follow appropriate service and safety procedures when servicing this product may result in per- sonal injury, destruction of expensive components and failure of the product to perform as specified. For these reasons, we advise all Yamaha product owners that all service requi
8、red should be performed by an authorized Yamaha Retailer or the appointed service representative. IMPORTANT :This presentation or sale of this manual to any individual or firm does not constitute authorization certifi- cation, recognition of any applicable technical capabilities, or establish a prin
9、cipal-agent relationship of any form. The data provided is belived to be accurate and applicable to the unit(s) indicated on the cover. The research engineering, and service departments of Yamaha are continually striving to improve Yamaha products. Modifications are, therefore, inevitable and change
10、s in specification are subject to change without notice or obligation to retrofit. Should any discrepancy appear to exist, please contact the distributors Service Division. WARNING :Static discharges can destroy expensive components. Discharge any static electricity your body may have accumulated by
11、 grounding yourself to the ground bus in the unit (heavy gauge black wires connect to this bus.) IMPORTANT :Turn the unit OFF during disassembly and parts replacement. Recheck all work before you apply power to the unit. WARNING: CHEMICAL CONTENT NOTICE! The solder used in the production of this pro
12、duct contains LEAD. In addition, other electrical/electronic and/or plastic (Where applicable) components may also contain traces of chemicals found by the California Health and Welfare Agency (and possibly other entities) to cause cancer and/or birth defects or other reproductive harm. DO NOT PLACE
13、 SOLDER, ELECTRICAL/ELECTRONIC OR PLASTIC COMPONENTS IN YOUR MOUTH FOR ANY REASON WHAT SO EVER! Avoid prolonged, unprotected contact between solder and your skin! When soldering, do not inhale solder fumes or expose eyes to solder/flux vapor! If you come in contact with solder or components located
14、inside the enclosure of this product, wash your hands before handling food. RadioFans.CN 收音机爱 好者资料库 EMX3000 3 SPECIFICATIONS General specifi cations Maximum output power STEREO: 300 W+300 W/4 0.5% THD at 1 kHz 215 W+215 W/8 0.5% THD at 1 kHz BRIDGE: 600 W/80.5% THD at 1 kHz Frequency response 20 Hz2
15、0 kHz +1 dB, 3 dB 1 W output into 8 (SPEAKER OUT) Channel Gain control at minimum. 20 Hz20 kHz +1 dB, 3 dB +4 dB output into 600 (ST OUT, MONO OUT, EFFECT SEND, MONITOR OUT) Channel Gain control at minimum. Total harmonic distortion Less than 0.5% 20 Hz20 kHz, 150 W output into 4 (SPEAKER OUT) Less
16、than 0.3% 20 Hz20 kHz, +14 dB output into 600 (ST OUT, MONO OUT, EFFECT SEND, MONITOR OUT) Hum & noise (Average, Rs=150 ) (with 20 Hz20 kHz BPF) 128 dB equivalent input noise 63 dB residual output noise (SPEAKER OUT) 95 dB residual output noise (ST OUT, MONO OUT, EFFECT SEND, MONITOR OUT) 87 dB (ST
17、OUT, MONO OUT) ST master/MONO master fader at maximum level and all channel fader at minimum. 64 dB (68 dB S/N) (ST OUT, MONO OUT) ST master/MONO master fader and 1 channel fader at maxi- mum level. And 1 channel Gain control at maximum. 80 dB (EFFECT SEND, MONITOR OUT) Master fader at maximum level
18、 and all channel level control at minimum. Maximum voltage gain 91 dBMIC IN to SPEAKER OUT (CH 18) 64 dBMIC IN to ST OUT(CH 18) 38 dBLINE IN to ST OUT(CH 18) 38 dBST IN to ST OUT(CH 9/10, 11/12) 70 dBMIC IN to EFFECT SEND (CH 18) 64 dBMIC IN to MONITOR OUT (CH 18) Crosstalk at 1 kHz70 dB adjacent in
19、put, 70 dB input to output MIC IN gain control44 dB variable POWER AMP level control14 dB variable Input channel equalization HIGH10 kHzshelving* MID2.5 kHzpeaking LOW100 Hzshelving* * Turn over/roll off frequency of shelving: 3 dB below maximum variable level. Meters13 points LED meter CH peak indi
20、catorsRed LED on each channel lits when POST EQ signal reaches the level 3 dB below clipping. LimiterComp. : THD0.5% LIMIT indicatorsTurn on THD0.5% Graphic equalizer7 bands (125, 250, 500, 1k, 2k, 4k, 8k Hz), 12 dB Maximum Internal digital effect16 programs, PARAMETER control Foot switchDigital eff
21、ect mute: on/off Protection circuit (Power amp)POWER switch on/off mute, DC detection, TEMP (heatsink temp. 90C) Fan circuitstop low speed (50C) variable high speed (70C) Phantom power+48 V is supplied to electrically balanced inputs. OptionFC5 (Foot switch) Power requirement/ Power consumption USA
22、and Canada:120 V AC 60 Hz, 250 W Europe:230 V AC 50 Hz, 300 W Other:240 V AC 50 Hz, 300 W Dimensions (WxHxD)480XX125 454 mm Weight16 kg AccessoriesPower cord, Owners Manual EMX3000 4 Input terminals Gain trim Actual load impedance For use with nominal Input level Connectors on mixer Sensitivity1 1.
23、Sensitivity is the lowest level that can produce an output of +4 dB (1.23 V) or the nominal output level when the unit is set at maximum gain. (All fader and level controls are at maximum position.) Max. before clip MIC INPUT (18) MAX MIN 5 k50600 Mics 60 dB (775 V) 16 dB (123 mV) 40 dB (7.75 mV) +4
24、 dB (1.23 V) XLR-3-31 type2 2. Balanced. (T=HOT, R=COLD, S=GND) LINE INPUT (18) MAX MIN 50 k 600 Lines 34 dB (15.5 mV) +10 dB (2.45 V) 14 dB (155 mV) +30 dB (24.5 V) PHONE JACK (TRS)2 ST INPUT (912) MAX MIN 10 k 34 dB (15.5 mV) +10 dB (2.45 V) 14 dB (155 mV) +30 dB (24.5 V) PHONE JACK3 3. Unbalanced
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- Yamaha EMX 3000 Service Manual 电路 原理图