Yamaha-DX-7-Service-Manual电路原理图.pdf

《Yamaha-DX-7-Service-Manual电路原理图.pdf》由会员分享，可在线阅读，更多相关《Yamaha-DX-7-Service-Manual电路原理图.pdf（16页珍藏版）》请在收音机爱好者资料库上搜索。

1、RadioFans.CN 收音机爱 好者资料库 RadioFans.CN 收音机爱 好者资料库 DX7 CIRCUIT DESCRIPTION 1.Keyboard and Panel Switch Scanning The 4 bits BO B3 from the sub-CPU (6805S) are input to the decoder (40H138). The decoder output is sent to the keyboard transfer contacts and the panel switches. The on or off state of the ke

2、yboard break contacts, make contacts and panel switches are sent to the sub-CPU AO A7 lines via a line driver (40H240) when the sub-CPU B4 and B5 lines are low. 2.Key ON/OFF and Touch Data The time it takes for the transfer contact to connect with the make contact after separating from the break con

3、tact is recorded by the sub-CPU timer. This value is the Touch data. The key ON signal is generated when the transfer contact connects with the make contact, and the key OFF signal is generated when the transfer contact connects with the break contact. 3.ADC Data entry Pitch bend wheel Modulation wh

4、eel Foot controller Breath controller After-touch controller Battery voltage The 7 analog control voltages given above are fed to the ADC (M58990P-l). The analog input selected by the sub-CPU BO B2 bits is converted to a digital value when the sub-CPU B7 line goes low. The ADC outputs a high level t

5、o the sub-CPU C3 line when the conversion is complete. The ADC sends the 8-bit digital value to the sub-CPU when the sub-CPU B6 line goes low. 4.Data Transmission from Sub-CPU to Main CPU 4-1.When a key event occurs the sub-CPU CO line goes high, changing the state of the ready flag (R S F/F) causin

6、g the main CPU IRQ and P21 lines to go low. 4-2.The main CPU accepts one byte of data on lines AO A7 from the sub-CPU when the P21 line goes low. 4-3.Once this byte is accepted, pin 9 of IC24 goes low, changing the state of F/F and forcing the sub-CPU Cl line low. 4-4.When the sub-CPU Cl line goes l

7、ow, step 4-1 (above) is repeated and then in step 4-2 a second byte of data is accepted by the main CPU. 4-5.During the IRQ routine the main CPU P20 line holds C2 on the sub-CPU line low until the second byte has been transferred. 4-6.Data is not accepted from the panel switches and keys while the s

8、ub-CPU C2 line is low. 5.Main CPU Operation The main CPU mode is set by externally initializing lines P20P22. When “L, L, H” is applied to the P20P22 lines and latched into the CPU on the rising edge of RES, the Extended Multiplex Mode is selected. In this mode, P40 P47 function as address lines. Th

9、e lower address bits are multiplexed with the data on lines P30 P37, and are separated by the address strobe signal SCI. P20 P24 and P10 P17 function as I/O lines. 6.RAM M5M511BP-15 X 8-bit CMOS RAM. 7.ROM 2764 8K X 8-bit NMOS EROM 8.LED The LED display is created via software. The LEDs are lit by d

10、ata latched from the main CPU. 9.LCD Data from the main CPU is decoded and displayed at the LCD unit. 10.EGS (Envelope Generator) 8 bits of data are received from the main CPU, and envelope and frequency data are sent to OPS. 11.OPS (Operator) The OPS uses a sine table to generate waveform data to b

11、e sent to the DAC from the received envelope and frequency data. The OPS permits combining the 6 operators in 32 different combinations. The combina- tions are called “algorithms”. One of the 6 operators is able to feed the sine table output back to the input. The feedback level and algorithm data i

12、s received from the main CPU. 12.DAC A BA9221 DAC is used. The DAC converts the digital waveform data from the OPS to an actual analog waveform. The amplitude scale factor of the analog waveform is controlled via SF0 SF3. This signal is then fed to the sample & hold and low-pass filter circuits from

13、 which it is sent to the output terminal. A reference voltage is applied to pin 14 of the DAC. 8 reference voltages are generated by the muPD405 1, and the total level is exter- nally controlled. 13.MIDI (Musical Instrument Digital Interface) Permits data transfer with other devices. Data is receive

14、d by P3 of the main CPU via a photo-coupler, and data is output from main CPU pin P24. EGS 1EGS Functions Receives data from the CPU, generates envelope & frequency data, & transmits the gener- ated data to OPS. (see EGS block diagram) Data received from the CPU is latched in the EGS & sent to the i

15、nternal data buss. 2EGS Rate/Level Buffer Rate refers to the time required for the next level to be reached. For example, Rl is the time it takes until Ll is reached from L4. The larger the Rl value, the sharper the attack. Rates and levels determine the basic shape of the envelope, but the actual e

16、nvelope shape is affected by output level and key scaling. 3.Output Level Buffer Output level buffer receives data concerning key scaling, after touch, and output level from the CPU. Actual values used for Ll to L4 are determined by the data stored in this buffer. Key scaling changes the output leve

17、l as shown below. 4.Frequency Buffer Frequency data related to key code, pitch envelope, and transposition is received from the CPU and stored in the frequency buffer. 5.Rate Scaling Buffer Data used to determine rate values according to key scaling is stored in the rate scaling buffer. 6.Values use

18、d for Rl to R4 are determined by the data stored in the frequency and rate scaling buffers. 7.Key Event Buffer Key states (ON/OFF) are stored in the key event buffer. 8.Modulation Sensitivity Buffer Amplitude modulation sensitivities are stored in the modulation sensitivity buffer. 9.Envelope Modula

19、tion Buffer Modulation states of the LFO are stored in the envelope generator buffer. 10.Envelope produced by the envelope generator is modulated by the data stored in the modulation sensitivity and envelope modulation buffers to generate the final envelope. 11.Detune Buffer Detune data according to

20、 key scaling is stored in the detune buffer. 12.Pitch Modulation Buffer LFO pitch modulation data is stored in the pitch modulation buffer. 13.Pitch Ratio Buffer Pitch ratios are stored in the pitch ratio buffer. 14.Data in the frequency buffer is modulated by the data stored in the detune, pitch modulation, and pitch ratio buffer to generate frequency data.