Yamaha-HTR-5635-Service-Manual电路原理图.pdf

《Yamaha-HTR-5635-Service-Manual电路原理图.pdf》由会员分享，可在线阅读，更多相关《Yamaha-HTR-5635-Service-Manual电路原理图.pdf（68页珍藏版）》请在收音机爱好者资料库上搜索。

1、SERVICE MANUAL 100849 IMPORTANT NOTICE This manual has been provided for the use of authorized YAMAHA Retailers and their service personnel. It has been assumed that basic service procedures inherent to the industry, and more specifically YAMAHA Products, are already known and understood by the user

2、s, and have therefore not been restated. WARNING:Failure to follow appropriate service and safety procedures when servicing this product may result in personal injury, destruction of expensive components, and failure of the product to perform as specified. For these reasons, we advise all YAMAHA pro

3、duct owners that any service required should be performed by an authorized YAMAHA Retailer or the appointed service representative. IMPORTANT:The presentation or sale of this manual to any individual or firm does not constitute authorization, certification or recognition of any applicable technical

4、capabilities, or establish a principle-agent relationship of any form. The data provided is believed to be accurate and applicable to the unit(s) indicated on the cover. The research, engineering, and service departments of YAMAHA are continually striving to improve YAMAHA products. Modifications ar

5、e, therefore, inevitable and specifications are subject to change without notice or obligation to retrofit. Should any discrepancy appear to exist, please contact the distributors Service Division. WARNING:Static discharges can destroy expensive components. Discharge any static electricity your body

6、 may have accumulated by grounding yourself to the ground buss in the unit (heavy gauge black wires connect to this buss). IMPORTANT:Turn the unit OFF during disassembly and part replacement. Recheck all work before you apply power to the unit. P.O.Box 1, Hamamatsu, Japan I CONTENTS TO SERVICE PERSO

7、NNEL . 2 IMPEDANCE SELECTOR . 2 FRONT PANEL . 3 REAR PANEL . 3 REMOTE CONTROL. 3 SPECIFICATIONS. 45 INTERNAL VIEW . 6 DISASSEMBLY PROCEDURES . 79 SELF DIAGNOSIS FUNCTION (DIAG) . 1026 AMP ADJUSTMENT . 26 DISPLAY DATA . 2728 IC DATA . 2934 BLOCK DIAGRAM. 3536 PRINTED CIRCUIT BOARD . 3746 PIN CONNECTI

8、ON DIAGRAM . 4748 SCHEMATIC DIAGRAM . 4954 PARTS LIST. 5565 REMOTE CONTROL. 6667 AV RECEIVER HTR-5635 HTR-5635 For U, C models RadioFans.CN 收音机爱 好者资料库 Copyright 2003 YAMAHA CORPORATION This manual is copyrighted by YAMAHA and may not be copied or redistributed either in print or electronically witho

9、ut permission. 2 HTR-5635 HTR-5635 IMPEDANCE SELECTOR WARNING: Do not change the IMPEDANCE SELECTOR switch setting while the power to this unit is on, otherwise this unit may be damaged. WALL OUTLET EQUIPMENT UNDER TEST AC LEAKAGE TESTER OR EQUIVALENT INSULATING TABLE WARNING: CHEMICAL CONTENT NOTIC

10、E! The solder used in the production of this product contains LEAD. In addition, other electrical/electronic and/or plastic (where applicable) components may also contain traces of chemicals found by the California Health and Welfare Agency (and possibly other entities) to cause cancer and/or birth

11、defects or other reproductive harm. DO NOT PLACE SOLDER, ELECTRICAL/ELECTRONIC OR PLASTIC COMPONENTS IN YOUR MOUTH FOR ANY REA- SON WHATSOEVER! Avoid prolonged, unprotected contact between solder and your skin! When soldering, do not inhale solder fumes or expose eyes to solder/flux vapor! If you co

12、me in contact with solder or components located inside the enclosure of this product, wash your hands before handling food. I TO SERVICE PERSONNEL 1. Critical Components Information Components having special characteristics are marked s and must be replaced with parts having specifications equal to

13、those originally installed. 2. Leakage Current Measurement (For 120V Models Only) When service has been completed, it is imperative to verify that all exposed conductive surfaces are properly insulated from supply circuits. GMeter impedance should be equivalent to 1500 ohm shunted by 0.15F. I IMPEDA

14、NCE SELECTOR “CAUTION” “F922: FOR CONTINUED PROTECTION AGAINST RISK OF FIRE, REPLACE ONLY WITH SAME TYPE 7A, 125V FUSE.” CAUTION F922: REPLACE WITH SAME TYPE 7A, 125V FUSE. ATTENTION F922: UTILISER UN FUSIBLE DE RECHANGE DE MEME TYPE DE 7A, 125V. GLeakage current must not exceed 0.5mA. GBe sure to t

15、est for leakage with the AC plug in both polarities. DIMENSIONS 151 (5-15/16) 130 (5-1/8)349.5 (13-3/4) 21 (13/16) 16 (5/8)14.5 (9/16) 380 (14-15/16) 435 (17-1/8) Unit : mm (inch) RadioFans.CN 收音机爱 好者资料库 3 HTR-5635 HTR-5635 I FRONT PANEL I REAR PANEL I REMOTE CONTROL SYSTEM POWERSTANDBYPOWER AV POWE

16、R TV POWER TV ENTER+1009 STEREOMATRIX 6.1SELECT- /DTS 8765 1 - MOVIE THTR - 2MONO MOVIETV SPORTS 4321 ENTERTAINMENTROCKJAZZHALL V-AUXVCRD-TV/CBLDVD SLEEPTUNERMD/CD-RCD TV AMP CODE SET MUTE INPUTMUTE REC 6CH INPUT AUDIO DISC SKIP VOLUME + + + CHVOL SET MENU SELECT PRESET/CH RAV301 WA65340 A/B/C/D/E L

17、EVEL MENU TEST RETURNDISPLAY TITLE + 4 HTR-5635 HTR-5635 I SPECIFICATIONS I Audio Section Minimum RMS Output Power (Power Amp. Section) (20 Hz to 20 kHz, 0.06% THD, 8 ohms) MAIN L/R.75W + 75W CENTER. 75W REAR L/R.75W + 75W (1 kHz, 0.09% THD, 8 ohms) MAIN L/R.85W + 85W CENTER. 85W REAR L/R.85W + 85W

18、Dynamic Power Per Channel (IHF) 8/6/4/2 ohms . 95/115/140/160W Damping Factor 20 Hz to 20 kHz, SPEAKER-A, 8 ohms . 80 or more Dynamic Headroom 8 ohms. 1.09dB Input Sensitivity / Input Impedance CD, etc. . 150 mV / 47 k-ohms EXT. DECODER MAIN L/R, CENTER, SURROUND L/R, SUB WOOFER . 150 mV / 47 k-ohms

19、 Maximum Input Signal Level (1 kHz, 0.5% THD, Effect On) CD, etc. .2.0V or more Output Level / Output Impedance REC OUT . 150 mV / 1.2 k-ohms SUB WOOFER (MAIN SP: Small). 4 V / 1.2 k-ohms Headphone Jack Rated Output / Impedance CD, etc. (1 kHz, 150 mV, 8 ohms). 0.34 V / 560 ohms Frequency Response C

20、D, etc. to MAIN L/R (10 Hz to 100 kHz) . 0/-3.0dB Total Harmonic Distortion (20Hz to 20kHz, 40W, 8 ohms) CD, etc. (Effect Off) to MAIN L/R SP OUT.0.06% or less Signal to Noise Ratio CD, etc. (Input shorted, EFFECT OFF) to MAIN L/R 250mV .100dB or more Residual Noise (IHF-A network) MAIN L/R SP OUT .

21、 150V or less Channel Separation (Vol -30 dB, Effect Off) CD, etc. (Input 5.1 k-ohms shorted, 1 kHz/10 kHz) . 60 dB or more/45 dB or more Tone Control Characteristics BASS Boost/Cut . 10dB (50Hz) Turnover Frequency . 350Hz TREBLE Boost/Cut . 10dB (20kHz) Turnover Frequency . 3.5kHz Filter Characteri

22、stics MAIN, REAR L/R SP Small (H.P.F.) .90Hz / 12dB oct. SUBWOOFER (L.P.F.) .90Hz / 18dB oct. I Video Section Video Signal Type . NTSC Video Signal Level . 1 Vp-p / 75 ohms Maximum Input Level . 1.5 Vp-p or more Signal to Noise Ratio .50 dB or more Monitor Out Frequency Response Video Signal Level .

23、5 Hz to 10 MHz, -3 dB I FM Section Tuning Range . 87.5 to 107.9 MHz 50dB Quieting Sensitivity (IHF) (1kHz, 100% Mod.) Mono . 2.0 V (17.3 dBf) Stereo . 25 V (39.2 dBf) Usable Sensitivity (IHF) Mono . 1.0 V (11.2 dBf) Selectivity at 400 kHz . 70 dB Signal to Noise Ratio (IHF) Mono / Stereo .76 dB / 70

24、 dB Harmonic Distortion (1 kHz) Mono/Stereo. 0.2 / 0.3 % Stereo Separation 1 kHz . 45 dB Frequency Response 20 Hz to 15 kHz .+0.5 / -2 dB Antenna Input . 75 ohms unbalanced I AM Section Tuning Range . 530 to 1,710 kHz Usable Sensitivity . 300 V/m Antenna . Loop Antenna I General Power Supply .AC 120

25、 V, 60 Hz Power Consumption . 210 W / 260 VA Standby Power Consumption (reference data) . 0.6 W AC Outlets 2 switched outlets . 100 W max. total Dimensions (W x H x D) . 435 x 151 x 387 mm (17-1/8 x 5-15/16 x 15-1/4) Weight . 10.0 kg (22 lbs. 1 oz.) Finish . Black color Accessories Remote Control, B

26、atteries (Manganese Dry), Indoor FM Antenna, AM Loop Antenna. * Specifications are subject to change without notice due to product improvements. Manufactured under license from Dolby Laboratories. “Dolby”, “Pro Logic” and the double-D symbol are trademarks of Dolby Laboratories. “DTS” and “DTS Digit

27、al Surround” are registered trademarks of Digital Theater Systems, Inc. 5 HTR-5635 HTR-5635 Set Menu Table No.MAIN MENUSUB MENU: PRESET VALUESETTING RANGES 1.SPEAKER SET1A. CENTER SP: LARGELARGE, SMALL, NONE 1B. MAIN SP: LARGELARGE, SMALL 1C. REAR L/R SP: LARGELARGE, SMALL, NONE 1D. LFE/BASS OUT: BO

28、THSW, MAIN, BOTH 1E. MAIN LEVEL: NORMALNORMAL, 10dB 2.LFE LEVELSP LFE LEVEL: 0dB20dB 0dB (1dB step) HP LFE LEVEL: 0dB20dB 0dB (1dB step) 3.SP DELAY TIMECENTER DELAY: 0ms0ms 5ms (1ms step) 4.DYNAMIC RANGESP DYNAMIC RANGE: MAXMAX, STD, MIN HP DYNAMIC RANGE: MAXMAX, STD, MIN 5.L/R BALANCECENTERL, , CEN

29、TER, , R (40 steps) 6.HP TONE CONTROLHP BASS: 0dB6dB +3dB (1dB step) HP TREBLE: 0dB6dB +3dB (1dB step) 7.I/O ASSIGNING7C (1). OPTICAL IN 1: DVDDVD 7C (2). COAXIAL IN 1: CDCD 8.INPUT MODEAUTOAUTO/LAST 9.DISPLAY SETDIMMER: 04 0 (1 step) 10.MEMORY GUARDOFFOFF/ON 6 HTR-5635 HTR-5635 I INTERNAL VIEW 1 FU

30、NCTION (9) P.C.B. 2 FUNCTION (7) P.C.B. 3 MAIN (6) P.C.B. 4 MAIN (10) P.C.B. 5 MAIN (2) P.C.B. 6 FUNCTION (3) P.C.B. 7 FUNCTION (2) P.C.B. 8 FUNCTION (10) P.C.B. 9 FUNCTION (4) P.C.B. 0 FUNCTION (1) P.C.B. A DSP P.C.B. B MAIN (3) P.C.B. C MAIN (1) P.C.B. D MAIN (4) P.C.B. E FUNCTION (5) P.C.B. F FUN

31、CTION (6) P.C.B. G MAIN (5) P.C.B. H OPERATION (3) P.C.B. I OPERATION (2) P.C.B. J OPERATION (1) P.C.B. 9 A 8 BGHF EDC JI 0 7634251 7 HTR-5635 HTR-5635 9 D0E I DISASSEMBLY PROCEDURES Fig. 1 (Remove parts in the order as numbered.) Disconnect the power cable from the AC outlet. 1. Removal of Top Cove

32、r a. Remove 4 screws (1) and 4 screws (2). (Fig. 1) b. Slide the Top Cover rearward to remove it. (Fig. 1) 2. Removal of Front Panel Unit a. Remove 5 screws (3) and then remove the Front Panel Unit. (Fig. 1) b. Remove CB309311. (Fig. 1) c. Loosen the harness fixture fixing the cable. 3. Removal of M

33、AIN (5) P.C.B. a. Remove 1 screw (4) and then remove the Jack Stopper (5) upward. (Fig. 1) b. Remove the MAIN (5) P.C.B. (Fig. 1) 4. Removal of DSP P.C.B. a. Remove 4 screws (6) and 1 screw (7), and then remove the Shield Case Cover. (Fig. 2) b. Remove 2 screws (8). (Fig. 2) c. Remove 2 screws (9).

34、(Fig. 3) d. Remove CB308. (Fig. 2) e. Remove the Shield Case Cover and the DSP P.C.B. (Fig. 2) Front Panel Unit 2 2 1 1 4 5 3 3 3 MAIN (5) P.C.B. Top Cover CB311 CB310 CB309 6 7 6 6 8 Shield Case Cover Shield Case DSP P.C.B. CB308 Fig. 2 Fig. 3 8 HTR-5635 HTR-5635 MAIN (10) P.C.B. MAIN (2) P.C.B. MA

35、IN (3) P.C.B. MAIN (1) P.C.B. MAIN (4) P.C.B. FUNCTION (5) P.C.B F C B C CB253 Fig. 6 6. Removal of MAIN (1), MAIN (3), MAIN (4) and FUNCTION (5) P.C.B.s a. Remove CB253. (Fig. 6) b. Remove 1 screw (B) and 2 screws (C). (Fig. 6) c. Remove MAIN (1), MAIN (3), MAIN (4) and FUNCTION (5) P.C.B.s. (Fig.

36、6) 7. Removal of MAIN (10) and MAIN (2) P.C.B.s a. Remove 4 screws (D). (Fig. 3) b. Remove MAIN (10) P.C.B. (Fig. 6) c. Remove 1 screw (E). (Fig. 3) d. Remove 1 screw (F). (Fig. 6) e. Remove MAIN (2) P.C.B. (Fig. 6) Fig. 4 Fig. 5 A CB312 When checking the P.C.B.: Put the rubber sheet and a cloth ove

37、r the equipment. Then place the P.C.B. upside down on the cloth and check it. (Fig. 5) Reconnect all cables (connectors) that have been disconnected. The P.C.B. removed from the rear panel does not work because its grounding is loose. Be sure to connect the ground of each P.C.B. to the chassis or GND with a jumper wire or the like. 5. Remova