Teac-CT-M631-S-Service-Manual电路原理图.pdf

《Teac-CT-M631-S-Service-Manual电路原理图.pdf》由会员分享，可在线阅读，更多相关《Teac-CT-M631-S-Service-Manual电路原理图.pdf（40页珍藏版）》请在收音机爱好者资料库上搜索。

1、RadioFans.CN 收音机爱 好者资料库 Model: CTM511/5S, CTM631/5S, CTM711/5S - Stereo Televisions Symptom: The instability of the Stereo Identification Signal on some high quality live stereo TV programs will cause split-second Sound distortion that may be confused as Sibilance. Replacement of C015 will improve f

2、iltering of the ID signal and remove any interference causing the effect. Stereo LED indicators may or may not switch off when distortion is audible. However, re-transmitted programs from overseas, movies and alike will not show any symptoms. Instruction: Incoming RF signal must be clean, high quali

3、ty live transmission to verify if a TV is effected (use the NEWS or ABC Kids programs for example). Check Stereo ID signal (117.5Hz) present on TP001 Pin 5 of TDA 3803A (IC001). The sinewave found should be at least 7.0 Vpp (AC) and may vary slightly in amplitude from station to station. Instability

4、 of this wave is synchronised with speech and music and will show as a milli-second collapse. Carefully remove Stereo PCB, disconnection all connectors and the link to the main PCB (going to R633). Replace C015 from the original 10nF with a 1nF Capacitor . Reconnect all connectors and the link, chec

5、k TP001 again. TP001 must be peaked to its maximum amplitude with T001 and thereafter readjusted to a more stable waveform with a shoulder distortion, as shown typically 6.5Vpp and 8.5ms , (use a suitable adjustment tool and do not readjust any other potentiometers on the Stereo PCB). Please note th

6、at the correct adjustment of T001 must result in a distinctive shoulder distortion on the positive rising edge of the sinewave, the falling side is undistorted. This is not the maximum amplitude adjustment as outlined in the service manual! Should you require any more information, please fax your en

7、quiry on (03) 646 5554 to the attention of the Technical Manager. Zoltan Sekula Technical Manager TEAC AUSTRALIA TECH MEMO #TV# 05.08.94 Distortion on rising shoulder. Perfect symmetrical waveform on negative half V. T RadioFans.CN 收音机爱 好者资料库 Model: CTM511/5S, CTM631/5S, CTM711/5S - Stereo Televisio

8、ns Symptom: All sets have in common a 12 Volt Zener Diode (ZD 402 - 12V/1W) short and limiting Resistor (0.68 and/or 6.2) open, or vertical collapse (TDA 3653B) and/or Horizontal output transistor (2SD1555 or 2SD1547) short. Confirmation: Check B+ as 112V/(143V respectively CTM 7xx) up by 30 to 40Vo

9、lts Check 12 Volt rail and if not there. Check Zener Diode (ZD 402) for short (near Vertical heatsink) (CTM511/515) Check R423 open (CTM631/635, CTM 711/715) Check R435 open (near EHT TRX) Instruction: Replace all faulty components and the following Capacitors in the Power supply. CTM CTM CTM Old Va

10、lue New Value 511/515 631/635 711/715 47uF/25V 47uF/63V C909 C910 C910 10uF/50V 10uF/100V C910 C908 C908 Also check the B+ rail capacitor and replace it if the powersupply failed as outlined above. Model Location Original: Replace with: CTM511 or 515 C915 47uF/160V 47uF/160V CTM631 or 635 C926 22uF/

11、160V 22uF/160V CTM711 or 715 C925 100uF/150V 100uF/160V Special Note: When a unit is repaired for the symptoms as described above and the Capacitors are not replaced, because it is not apparent that they are faulty, it will result in a repeated breakdown within days after completion of the repair. I

12、t is imperative that all Televisions with the above model number, irrespective of the original complaint, have the outlined power supply Capacitors replaced as a matter of preventative service. Should you require any more information, please fax your enquiry on (03) 646 5554 to the attention of the Technical Manager. TEAC AUSTRALIA TECH MEMO 23.07.94