Sony-STR-DA7ES-Service-Manual电路原理图.pdf

上传人：cc518

文档编号：86172

上传时间：2024-07-17

格式：PDF

页数：116

大小：14.50MB

《Sony-STR-DA7ES-Service-Manual电路原理图.pdf》由会员分享，可在线阅读，更多相关《Sony-STR-DA7ES-Service-Manual电路原理图.pdf（116页珍藏版）》请在收音机爱好者资料库上搜索。

1、US Model Canadian Model STR-DA4ES/DA7ES AEP Model E Model STR-VA333ES SPECIFICATIONS Photo: STR-VA333ES This receiver incorporates Dolby* Digital and Pro Logic Surround and the DTS* Digital Surround System. * Manufactured under license from Dolby Laboratories. “Dolby”, “Pro Logic” and the double-D s

2、ymbol are trademarks of Dolby Laboratories. * “DTS”, “DTS-ES Extended Surround” and “Neo: 6” are trademarks of Digital Theater Systems, Inc. STR-DA4ES/DA7ES AUDIO POWER SPECIFICATIONS POWER OUTPUT AND TOTAL HARMONIC DISTORTION: With 8 ohm loads, both channels driven, from 20 20,000 Hz; rated DA4ES:

3、110, DA7ES: 120 watts per channel minimum RMS power, with no more than 0.05 % total harmonic distortion from 250 milliwatts to rated output. AMPLIFIER SECTION POWER OUTPUT Rated Power Output at Stereo Mode (8 ohms 20 Hz 20 kHz, THD 0.05 %) STR-DA7ES:120 W + 120 W STR-DA4ES:110 W + 110 W (4 ohms 20 H

4、z 20 kHz, THD 0.09 %) STR-DA7ES:100 W + 100 W STR-DA4ES:90 W + 90 W Reference Power Output (8 ohms 20 Hz 20 kHz, THD 0.05 %) STR-DA7ES:FRONT 1) : 120 W + 120 W CENTER 1) : 120 W SURR 1) : 120 W + 120 W SURR BACK 1) : 120 W + 120 W STR-DA4ES:FRONT 1) : 110 W + 110 W CENTER 1) : 110 W SURR 1) : 110 W

5、+ 110 W SURR BACK 1) : 110 W + 110 W (4 ohms 20 Hz 20 kHz, THD 0.09 %) STR-DA7ES:FRONT 1) : 100 W + 100 W CENTER 1) : 100 W SURR 1) : 100 W + 100 W SURR BACK 1) : 100 W + 100 W STR-DA4ES:FRONT 1) : 90 W + 90 W CENTER 1) : 90 W SURR 1) : 90 W + 90 W SURR BACK 1) : 90 W + 90 W 1) Depending on the soun

6、d field settings and the source, there may be no sound output. STR-DA4ES/DA7ES/VA333ES Ver 1.0 2002. 07 SERVICE MANUAL Continued on next page Sony Corporation Home Audio Company Published by Sony Engineering Corporation 9-874-082-01 2002G0400-1 2002. 07 FM STEREO FM-AM RECEIVER RadioFans.CN 收音机爱好者资

7、料库 2 STR-DA4ES/DA7ES/VA333ES Frequency response PHONORIAA equalization curve 0.5 dB CD/SACD, TAPE,10 Hz 100 kHz MD/DAT, TV/SAT,+0.5/2 dB (with sound DVD/LD, VIDEO 1, 2,field, equalizer, and bass 3boost bypassed) Inputs (Analog) PHONOSensitivity: 2.5 mV Impedance: 50 kilohms S/N 2) : 86 dB (A, 2.5 mV

8、 3) ) MULTI CHANNELSensitivity: 150 mV IN 1, 2, CD/SACD,Impedance: 50 kilohms TAPE, MD/DAT,S/N 2) : 100 dB DVD/LD, TV/SAT,(A, 150 mV 3) ) VIDEO 1, 2, 3 2) INPUT SHORT. 3) Weighted network, input level. Inputs (Digital) CD/SACD, DVD/LDSensitivity: (Coaxial)Impedance: 75 ohms S/N: 100 dB (A, 20 kHz LP

9、F) CD/SACD, DVD/LD,Sensitivity: TV/SAT,Impedance: MD/DAT (Optical)S/N: 100 dB (A, 20 kHz LPF) Outputs TAPE, MD/DATVoltage: 150 mV (REC OUT), VIDEOImpedance: 10 kilohms 1, 2 (AUDIO OUT) FRONT L/R,Voltage: 2 V CENTER,Impedance: 1 kilohms SURROUND L/R, SURROUND BACK L/R, SUB WOOFER EQ BASS:99 Hz1.0 kHz

10、 (21 steps) MID (FRONT L/R, CENTER only): 198 Hz10 kHz (36 steps) TREBLE:1.0 kHz10 kHz (23 steps) Gain levels:10 dB, 0.5 dB step FM TUNER SECTION Tuning range87.5 - 108.0 MHz Antenna terminals75 ohms, unbalanced Sensitivity Mono:18.3 dBf, 2.2 V/75 ohms Stereo:38.3 dBf, 22.5 V/75 ohms Usable sensitiv

11、ity11.2 dBf, 1 V/75 ohms S/N Mono:76 dB Stereo:70 dB Harmonic distortion at 1 kHz Mono:0.3% Stereo:0.5% Separation45 dB at 1 kHz Frequency response30 Hz 15 kHz, +0.5/2 dB Selectivity60 dB at 400 kHz AM TUNER SECTION Tuning range With 10-kHz tuning scale:530 1710 kHz 4) With 9-kHz tuning scale:531 17

12、10 kHz 4) AntennaLoop antenna Usable sensitivity50 dB/m (at 1,000 kHz or 999 kHz) S/N54 dB (at 50 mV/m) Harmonic distortion0.5 % (50 mV/m, 400 kHz) Selectivity At 9 kHz:35 dB At 10 kHz:40 dB 4) You can change the AM tuning scale to 9 kHz or 10 kHz. After tuning in any AM station, turn off the receiv

13、er. Hold down TUNING + and press ?/1 . All preset stations will be erased when you change the tuning scale. To reset the scale to 10 kHz (or 9 kHz), repeat the procedure. VIDEO SECTION Inputs/Output Video:1 Vp-p, 75 ohms S-video:Y: 1 Vp-p, 75 ohms C: 0.286 Vp-p, 75 ohms COMPONENT VIDEO:Y: 1 Vp-p, 75

14、 ohms B-Y: 0.7 Vp-p, 75 ohms R-Y: 0.7 Vp-p, 75 ohms RadioFans.CN 收音机爱好者资料库 3 STR-DA4ES/DA7ES/VA333ES REMOTE CONTROL RM-US105A (STR-DA7ES only) Remote control systemInfrared control Power requirements3 V DC with two R6 (size-AA) batteries Dimensions210 45 25 mm Mass (approx.)95 g excluding batteries

15、 GENERAL Power requirements120 V AC, 60 Hz Power consumption Models of area code U STR-DA7ES:450 W STR-DA4ES:420 W Models of area code CA STR-DA7ES:490 VA STR-DA4ES:470 VA Power consumption (during standby mode) 1 W AC outlets2 switched, 120 W/1A Dimensions430 174 465 mm including projecting parts a

16、nd controls Mass (Approx.) STR-DA7ES:21.0 kg STR-DA4ES:21.0 kg Supplied accessories FM wire antenna (1) AM loop antenna (1) Audio/video/control S cord (1) Control S cord (mini jack) (1) STR-DA7ES only; Remote commander RM-TP1 (1) Base unit RMB-TP1 (1 for RM-TP1) AC adapter (1 for RM-TP1) Remote comm

17、ander RM-US105A (1) R6 (size-AA) batteries (2) STR-DA4ES only; Remote commander RM-LP211 (1) LR6 (size-AA) batteries (3) Design and specifications are subject to change without notice. STR-VA333ES AMPLIFIER SECTION Models of area code TW: Power Output (8 ohms 20 Hz 20 kHz, THD 0.05 %) 100 W + 100 W

18、(4 ohms 20 Hz 20 kHz, THD 0.09 %) 90 W + 90 W Reference Power Output (8 ohms 20 Hz 20 kHz, THD 0.05 %) FRONT1): 100 W + 100 W CENTER1): 100 W SURR1): 100 W + 100 W SURR BACK1): 100 W + 100 W (4 ohms 20 Hz 20 kHz, THD 0.09 %) FRONT1): 90 W + 90 W CENTER1): 90 W SURR1): 90 W + 90 W SURR BACK1): 90 W +

19、 90 W 1) Depending on the sound field settings and the source, there may be no sound output. Models of area code CEL, KR: Power Output (8 ohms 1 kHz, THD 0.7 %) 100 W + 100 W2) 90 W + 90 W3) (4 ohms 1 kHz, THD 0.7 %) 90 W + 90 W2) 80 W + 80 W3) Reference Power Output (8 ohms 1 kHz, THD 0.7 %) FRONT4

20、): 100 W + 100 W CENTER4): 100 W SURR4): 100 W + 100 W SURR BACK4): 100 W + 100 W (4 ohms 1 kHz, THD 0.7 %) FRONT4): 90 W + 90 W CENTER4): 90 W SURR4): 90 W + 90 W SURR BACK4): 90 W + 90 W (8 ohms 20 Hz 20 kHz, THD 0.05 %) FRONT4): 90 W + 90 W CENTER4): 90 W SURR4): 90 W + 90 W SURR BACK4): 90 W + 9

21、0 W (4 ohms 20 Hz 20 kHz, THD 0.05 %) FRONT4): 80 W + 80 W CENTER4): 80 W SURR4): 80 W + 80 W SURR BACK4): 80 W + 80 W 2) Measured under the following conditions: Models of area code CEL: 230 V AC, 50 Hz 3) Measured under the following conditions: Models of area code KR: 220 V AC, 60 Hz 4) Depending

22、 on the sound field settings and the source, there may be no sound output. 4 STR-DA4ES/DA7ES/VA333ES Frequency response PHONORIAA equalization curve 0.5 dB CD/SACD, TAPE,10 Hz 100 kHz MD/DAT, TV/SAT,+0.5/2 dB (with sound DVD/LD, VIDEO 1, 2,field, equalizer, and bass 3boost bypassed) Inputs (Analog)

23、PHONOSensitivity: 2.5 mV Impedance: 50 kilohms S/N5): 86 dB (A, 2.5 mV6) MULTI CHANNELSensitivity: 150 mV IN 1, 2, CD/SACD,Impedance: 50 kilohms TAPE, MD/DAT,S/N5): 100 dB DVD/LD, TV/SAT,(A, 150 mV6) VIDEO 1, 2, 3 5) INPUT SHORT. 6) Weighted network, input level. Inputs (Digital) CD/SACD, DVD/LDSens

24、itivity: (Coaxial)Impedance: 75 ohms S/N: 100 dB (A, 20 kHz LPF) CD/SACD, DVD/LD,Sensitivity: TV/SAT,Impedance: MD/DAT (Optical)S/N: 100 dB (A, 20 kHz LPF) Outputs TAPE, MD/DATVoltage: 150 mV (REC OUT), VIDEOImpedance: 10 kilohms 1, 2 (AUDIO OUT) FRONT L/R,Voltage: 2 V CENTER,Impedance: 1 kilohms SU

25、RROUND L/R, SURROUND BACK L/R, SUB WOOFER EQ BASS:99 Hz1.0 kHz (21 steps) MID (FRONT L/R, CENTER only): 198 Hz10 kHz (36 steps) TREBLE:1.0 kHz10 kHz (23 steps) Gain levels:10 dB, 0.5 dB step FM TUNER SECTION Tuning range87.5 108.0 MHz Antenna terminals75 ohms, unbalanced Sensitivity Mono:18.3 dBf, 2

26、.2 V/75 ohms Stereo:38.3 dBf, 22.5 V/75 ohms Usable sensitivity11.2 dBf, 1 V/75 ohms S/N Mono:76 dB Stereo:70 dB Harmonic distortion at 1 kHz Mono:0.3% Stereo:0.5% Separation45 dB at 1 kHz Frequency response30 Hz 15 kHz, +0.5/2 dB Selectivity60 dB at 400 kHz AM TUNER SECTION Tuning range531 1602 kHz

27、 AntennaLoop antenna Usable sensitivity50 dB/m (at 999 kHz) S/N54 dB (at 50 mV/m) Harmonic distortion0.5 % (50 mV/m, 400 Hz) Selectivity35 dB VIDEO SECTION Inputs/Outputs Video:1 Vp-p, 75 ohms S-video:Y: 1 Vp-p, 75 ohms C: 0.286 Vp-p, 75 ohms COMPONENT VIDEO:Y: 1 Vp-p, 75 ohms B-Y: 0.7 Vp-p, 75 ohms

28、 R-Y: 0.7 Vp-p, 75 ohms 5 STR-DA4ES/DA7ES/VA333ES SAFETY-RELATED COMPONENT WARNING! COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN I

29、N THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY. ATTENTION AU COMPOSANT AYANT RAPPORT LA SCURIT! LES COMPOSANTS IDENTIFS PAR UNE MARQUE 0 SUR LES DIAGRAMMES SCHMATIQUES ET LA LISTE DES PICES SONT CRITIQUES POUR LA SCURIT DE FONCTIONNEMENT. NE REMPLACER CES COMPOSANTS QUE PAR DES PISES SONY DONT LE

30、S NUMROS SONT DONNS DANS CE MANUEL OU DANS LES SUPPMENTS PUBLIS PAR SONY. MODEL IDENTIFICATION BACK PANEL MODELPARTS No. DA7ES: US model4-240-816-0s DA7ES: CND model4-240-816-1s DA4ES: US model4-240-816-2s DA4ES: CND model VA333ES: AEP model4-240-816-4s VA333ES: KR model4-240-816-5s VA333ES: TW mode

31、l4-240-816-6s PART NO. Abbreviation CND : Canadian model KR: Korea model TW: Taiwan model AREA CODE Fig. 1 4-240-816-3s About area codes The area code of the receiver you purchased is shown on the lower portion of the rear panel (see the illustration below). Any differences in operation, according t

32、o the area code, are clearly indicated in the text, for example, “Models of area code AA only”. Area code 4-XXX-XXX-XX AA AC OUTLET LR + SURROU D URR ACK CENTERSURR B CK LRSURROU DCENTERSURR B CK URR ACK SPEAKERS MPEDANCE SELECTOR 4 8 GENERAL Power requirements Area codePower requirements CEL230 V A

33、C, 50/60 Hz TW110 V AC, 60 Hz KR220 V AC, 60 Hz Power consumption Area codePower consumption CEL, KR390 W TW400 W (max. 1,000 W) Power consumption (during standby mode) 1 W AC outlets Area codeAC outlets CEL1 switched, 100 W TW2 switched, 100 W Dimensions430 175 465 mm including projecting parts and

34、 controls Mass (Approx.)21.0 kg Supplied accessories FM wire antenna (1) AM loop antenna (1) Remote commander RM-LP211 (1) LR6 (size-AA) batteries (3) Design and specifications are subject to change without notice. 6 STR-DA4ES/DA7ES/VA333ES After correcting the original service problem, perform the

35、fol- lowing safety checks before releasing the set to the customer: Check the antenna terminals, metal trim, “metallized” knobs, screws, and all other exposed metal parts for AC leakage. Check leakage as described below. LEAKAGE The AC leakage from any exposed metal part to earth ground and from all

36、 exposed metal parts to any exposed metal part having a return to chassis, must not exceed 0.5 mA (500 microampers). Leakage current can be measured by any one of three methods. 1. A commercial leakage tester, such as the Simpson 229 or RCA WT-540A. Follow the manufacturers instructions to use these

37、 instruments. 2. A battery-operated AC milliammeter. The Data Precision 245 digital multimeter is suitable for this job. 3. Measuring the voltage drop across a resistor by means of a VOM or battery-operated AC voltmeter. The “limit” indication is 0.75 V, so analog meters must have an accurate low-vo

38、ltage scale. The Simpson 250 and Sanwa SH-63Trd are examples of a pas- sive VOM that is suitable. Nearly all battery operated digital multimeters that have a 2V AC range are suitable. (See Fig. A) SAFETY CHECK-OUT (US model only) To Exposed Metal Parts on Set 0.15 F 1.5 k AC Voltmeter (0.75 V) Earth

39、 Ground Fig. A. Using an AC voltmeter to check AC leakage. Notes on chip component replacement Never reuse a disconnected chip component. Notice that the minus side of a tantalum capacitor may be damaged by heat. EXTENSION CABLE AND SERVICE POSITION When repairing or serving this set, connect the ji

40、g (extension cable) as shown below. Connect the Digital board (CN2102) and the E-Vol board (CNP402) with the extension cable (Part No. J-2501-049-A). DIGITAL board CNP402 CN2102 E-VOL board J-2501-049-A 7 STR-DA4ES/DA7ES/VA333ES TABLE OF CONTENTS 1. SERVICE NOTE 8 2. GENERAL 9 3. TEST MODE 11 4. DIS

41、ASSEMBLY 4-1.Case . 12 4-2.Panel Assy . 13 4-3.Bracket. 13 4-4.Back Panel Section .14 4-5.Digital Board . 14 4-6.Input Board, E-vol Board . 15 4-7.A-class Board, Amp Board.15 4-8.Ac Board, Cis Power Board . 16 4-9.Dc Board.16 5. ELECTRICAL ADJUSTMENTS 17 6. DIAGRAMS 6-1.IC Pin Function . 18 6-2.Bloc

42、k Diagram Audio Section . 22 6-3.Block Diagram Video Section . 23 6-4.Block Diagram Digital Section (1/2).24 6-5.Block Diagram Digital Section (2/2).25 6-6.Block Diagram Power Amp Section. 26 6-7.Circuit Boards Location .27 6-8.Schematic Diagram Digital Section (1/7) .29 6-9.Schematic Diagram Digita

43、l Section (2/7) .30 6-10. Schematic Diagram Digital Section (3/7) .31 6-11. Schematic Diagram Digital Section (4/7) .32 6-12. Schematic Diagram Digital Section (5/7) .33 6-13. Schematic Diagram Digital Section (6/7) .34 6-14. Schematic Diagram Digital Section (7/7) .35 6-15. Printed Wiring Board Dig

44、ital Section . 36 6-16. Printed Wiring Board Input Section . 38 6-17. Schematic Diagram Input Section .40 6-18. Printed Wiring Boards S-Video Section .41 6-19. Schematic Diagram S-Video Section (1/2) . 42 6-20. Schematic Diagram S-Video Section (2/2) . 43 6-21. Printed Wiring Boards C-Video Section

45、. 44 6-22. Schematic Diagram C-Video Section.45 6-23. Printed Wiring Boards E-Vol Section.46 6-24. Schematic Diagram E-Vol Section (1/2) . 48 6-25. Schematic Diagram E-Vol Section (2/2) . 49 6-26. Printed Wiring Board A-Class Section. 50 6-27. Schematic Diagram A-Class Section .51 6-28. Printed Wiring Board CIS Section .52 6-29. Schematic Diagram CIS Section . 53 6-30. Printed Wiring Board Up Convert