Sony-SCD-XA9000ES-Service-Manual电路原理图.pdf

《Sony-SCD-XA9000ES-Service-Manual电路原理图.pdf》由会员分享，可在线阅读，更多相关《Sony-SCD-XA9000ES-Service-Manual电路原理图.pdf（124页珍藏版）》请在收音机爱好者资料库上搜索。

1、SERVICE MANUAL When a super audio CD is played Playing frequency range2 Hz to 100 kHz Frequency response2 Hz to 50 kHz (3 dB) Dynamic range108 dB or more Total harmonic distortion rate 0.0012 % or less Wow and flutterValue of measurable limit ( 0.001 % W. PEAK) or less When a CD is played Frequency

2、response2 Hz to 20 kHz Dynamic range100 dB or more Total harmonic distortion rate 0.0017 % or less Wow and flutterValue of measurable limit ( 0.001 % W. PEAK) or less Output connector *Output only the audio signals of the CD i.LINK section Pin4 pins Transmission speedS200 (Maximum data transmission

3、speed 200 Mbps) Transmission protocolA/M transmission protocol Format (output)Super Audio CD* (DSD PLAIN) 2 channel linear PCM (IEC 60958-3) Sampling frequency: 44.1 kHz * Conforms to the copy protection technology of DTLA (Revision 1.2). ANALOG OUT DIGITAL (CD) OUT OPTICAL* DIGITAL (CD) OUT COAXIAL

4、* PHONES Jack type Phono jacks Square optical output connector Coaxial output connector Stereo phone jack Output level 2 Vrms (at 50 kilohms) 18 dBm 0.5 Vp-p 10 mW Load impedance Over 10 kilohms Light emitting wave length: 660 nm 75 ohms 32 ohms ( ) General LaserSemiconductor laser (SA-CD: = 650 nm)

5、 (CD: = 780 nm) Emission duration: continuous Laser radiant power:5.47 uW at 650 nm *These output is the value measured at a distance of about 200mm from the objective lens surface on the optical pick-up. Power requirements US, Canadian models: 120 V AC, 60 Hz Taiwan model: 110 V AC, 60 Hz AEP model

6、: 230 V AC, 50/60 Hz Power consumption32 W Dimensions (w/h/d)430 127 387 mm (17 5 15 1/4 in.) incl. projecting parts Mass (approx.)16.2 kg (35 lbs 12 oz.) Supplied accessories Design and specifications are subject to change without notice. Audio connecting cord phono jack 2 (Red and White) y phono j

7、ack 2 (Red and White) (3) phono jack 1 (Black) y phono jack 1 (Black) (2) i.LINK connecting cord (1) Remote commander RM-SX700 (1) Size AA (R6) batteries (2) AC power cord (1) Plug adapter (1) (US, Canadian models only) Model Name Using Similar MechanismNEW CD Mechanism Type CDM19JB-DVBU4C (Except A

8、EP: Silver type) CDM19JB-DVBU4D (AEP: Silver type) Base Unit Name DVBU4C (Except AEP: Silver type) DVBU4D (AEP: Silver type) Optical Pick-up NameKHM-230AAA SUPER AUDIO CD PLAYER US Model Canadian Model AEP Model E Model SPECIFICATIONS SCD-XA9000ES Ver. 1.4 2005.11 9-961-151-05Sony Corporation 2005K0

9、5-1Home Audio Division C 2005.11Published by Sony Engineering Corporation RadioFans.CN 收音机爱 好者资料库 2 SCD-XA9000ES CAUTION The use of optical instruments with this product will increase eye hazard. For the customers in Canada This Class B digital apparatus complies with Canadian ICES-003. ATTENTION AU

10、 COMPOSANT AYANT RAPPORT LA SCURIT! LES COMPOSANTS IDENTIFIS PAR UNE MARQUE 0 SUR LES DIAGRAMMES SCHMATIQUES ET LA LISTE DES PICES SONT CRITIQUES POUR LA SCURIT DE FONCTIONNEMENT. NE REMPLACER CES COM- POSANTS QUE PAR DES PICES SONY DONT LES NUMROS SONT DONNS DANS CE MANUEL OU DANS LES SUPPLMENTS PU

11、BLIS PAR SONY. SAFETY-RELATED COMPONENT WARNING! COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUB

12、- LISHED BY SONY. Notes on chip component replacement Never reuse a disconnected chip component. Notice that the minus side of a tantalum capacitor may be dam- aged by heat. Flexible Circuit Board Repairing Keep the temperature of the soldering iron around 270 C dur- ing repairing. Do not touch the

13、soldering iron on the same conductor of the circuit board (within 3 times). Be careful not to apply force on the conductor when soldering or unsoldering. CAUTION Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous ra- diation exposure

14、. This appliance is classified as a CLASS 1 LASER product. The CLASS 1 LASER PRODUCT MARKING is located on the rear exterior. SAFETY CHECK-OUT After correcting the original service problem, perform the follow- ing safety check before releasing the set to the customer: Check the antenna terminals, me

15、tal trim, “metallized” knobs, screws, and all other exposed metal parts for AC leakage. Check leakage as described below. LEAKAGE TEST The AC leakage from any exposed metal part to earth ground and from all exposed metal parts to any exposed metal part having a return to chassis, must not exceed 0.5

16、 mA (500 microamperes.). Leakage current can be measured by any one of three methods. 1.A commercial leakage tester, such as the Simpson 229 or RCA WT-540A. Follow the manufacturers instructions to use these instruments. 2.A battery-operated AC milliammeter. The Data Precision 245 digital multimeter

17、 is suitable for this job. 3.Measuring the voltage drop across a resistor by means of a VOM or battery-operated AC voltmeter. The “limit” indication is 0.75 V, so analog meters must have an accurate low-voltage scale. The Simpson 250 and Sanwa SH-63Trd are examples of a pas- sive VOM that is suitabl

18、e. Nearly all battery operated digital multimeters that have a 2 V AC range are suitable. (See Fig. A) Fig. A.Using an AC voltmeter to check AC leakage. 1.5 k0.15 F AC voltmeter (0.75 V) To Exposed Metal Parts on Set Earth Ground AEP model UNLEADED SOLDER Boards requiring use of unleaded solder are

19、printed with the lead- free mark (LF) indicating the solder contains no lead. (Caution: Some printed circuit boards may not come printed with the lead free mark due to their particular size) : LEAD FREE MARK Unleaded solder has the following characteristics. Unleaded solder melts at a temperature ab

20、out 40 C higher than ordinary solder. Ordinary soldering irons can be used but the iron tip has to be applied to the solder joint for a slightly longer time. Soldering irons using a temperature regulator should be set to about 350 C. Caution: The printed pattern (copper foil) may peel away if the he

21、ated tip is applied for too long, so be careful! Strong viscosity Unleaded solder is more viscou-s (sticky, less prone to flow) than ordinary solder so use caution not to let solder bridges occur such as on IC pins, etc. Usable with ordinary solder It is best to use only unleaded solder but unleaded

22、 solder may also be added to ordinary solder. RadioFans.CN 收音机爱 好者资料库 3 SCD-XA9000ES TABLE OF CONTENTS 1.SERVICING NOTES.4 2.GENERAL. 10 3.DISASSEMBLY 3-1.Disassembly Flow . 13 3-2.Case (Top), Side Plate. 14 3-3.Loading Panel Assy. 14 3-4.Front Panel Section . 15 3-5.MAIN Board, Bracket (MAIN) . 15

23、3-6.RF Board, Mechanism Deck (CDM19JB-DVBU4C or CDM19JB-DVBU4D) . 16 3-7.Disc Table, Belt, Loading Motor (M1). 16 3-8.Optical Pick-up (KHM-230AAA) . 17 3-9.Base Unit (DVBU4C or DVBU4D). 18 4.TEST MODE. 19 5.DIAGRAMS 5-1.Block Diagram RF/SERVO Section . 26 5-2.Block Diagram MAIN Section (1/2) . 27 5-

24、3.Block Diagram MAIN Section (2/2) . 28 5-4.Block Diagram AUDIO Section (1/2) . 29 5-5.Block Diagram AUDIO Section (2/2) . 30 5-6.Block Diagram LINK Section . 31 5-7.Block Diagram PANEL/POWER SUPPLY Section . 32 5-8.Note for Printed Wiring Boards and Schematic Diagrams . 33 5-9.Printed Wiring Boards

25、 SERVO Section . 34 5-10. Schematic Diagram SERVO Section . 35 5-11. Printed Wiring Board MAIN Board (Component Side) . 36 5-12. Printed Wiring Board MAIN Board (Conductor Side) . 37 5-13. Schematic Diagram MAIN Board (1/7) . 38 5-14. Schematic Diagram MAIN Board (2/7) . 39 5-15. Schematic Diagram M

26、AIN Board (3/7) . 40 5-16. Schematic Diagram MAIN Board (4/7) . 41 5-17. Schematic Diagram MAIN Board (5/7) . 42 5-18. Schematic Diagram MAIN Board (6/7) . 43 5-19. Schematic Diagram MAIN Board (7/7) . 44 5-20. Printed Wiring Board D-OUT Board . 45 5-21. Schematic Diagram D-OUT Board . 45 5-22. Prin

27、ted Wiring Board MOTHER Board (Component Side) . 46 5-23. Printed Wiring Board MOTHER Board (Conductor Side) . 47 5-24. Schematic Diagram MOTHER Board (1/2) . 48 5-25. Schematic Diagram MOTHER Board (2/2) . 49 5-26. Printed Wiring Board AUDIO FRONT Board . 50 5-27. Schematic Diagram AUDIO FRONT Boar

28、d . 51 5-28. Printed Wiring Board AUDIO SURR Board . 52 5-29. Schematic Diagram AUDIO SURR Board . 53 5-30. Printed Wiring Board AUDIO C/SW Board . 54 5-31. Schematic Diagram AUDIO C/SW Board . 55 5-32. Schematic Diagram LINK Board (1/2) . 56 5-33. Schematic Diagram LINK Board (2/2) . 57 5-34. Print

29、ed Wiring Board LINK Board . 58 5-35. Printed Wiring Boards PANEL Section . 59 5-36. Schematic Diagram PANEL Section (1/2) . 60 5-37. Schematic Diagram PANEL Section (2/2) . 61 5-38. Printed Wiring Board A-POWER Board (Component Side) . 62 5-39. Printed Wiring Boards A-POWER (Conductor Side)/IC Boar

30、ds . 63 5-40. Schematic Diagram A-POWER/IC Boards . 64 5-41. Printed Wiring Board D-POWER Board . 66 5-42. Schematic Diagram D-POWER Board . 67 5-43. Printed Wiring Boards AC/AC SW Boards . 68 5-44. Schematic Diagram AC/AC SW Boards . 69 5-45. IC Pin Function Description . 74 6.EXPLODED VIEWS 6-1.Ca

31、se Section . 94 6-2.Front Panel Section-1. 95 6-3.Front Panel Section-2. 96 6-4.Bottom Section. 97 6-5.Board Section-1. 98 6-6.Board Section-2. 99 6-7.Chassis Section .100 6-8.Mechanism Deck Section .101 6-9.Base Unit Section.102 7.ELECTRICAL PARTS LIST.103 Ver. 1.3 4 SCD-XA9000ES SECTION 1 SERVICIN

32、G NOTES The laser diode in the optical pick-up block may suffer electro- static break-down because of the potential difference generated by the charged electrostatic load, etc. on clothing and the human body. During repair, pay attention to electrostatic break-down and also use the procedure in the

33、printed matter which is included in the repair parts. The flexible board is easily damaged and should be handled with care. NOTES ON LASER DIODE EMISSION CHECK The laser beam on this model is concentrated so as to be focused on the disc reflective surface by the objective lens in the optical pick-up

34、 block. Therefore, when checking the laser diode emis- sion, observe from more than 30 cm away from the objective lens. CLEANING OF OPTICAL PICK-UP LENS In cleaning the lens of optical pick-up, use the air blower. Never use a cotton swab for cleaning the lens of optical pick-up, which otherwise caus

35、es a trouble. RESETTING OPERATION AT POWER ON If the power is turned on with a disc loaded in the set, a sequence of operation as shown below will be performed. (The operation varies depending on the type of disc) Condition: continue mode (1) CD 1.Sled reverse move (sled in) 2.Disc detect 3.IC setti

36、ng for CD 4.Servo error signal offset auto adjustment 5.Spindle kick for LD on 6.LD on 7.Focus search 8.Focus servo on 9.Spindle kick 10. Spindle servo on 11. E-F balance auto adjustment 12. Tracking when you turn the . AMS dial clockwise by one click, you go to the succeeding track. PHONESPHONE LEV

37、EL MNMAX PUSH EN ER AMS TME/TEXTSACDCDMENUMULTI/2CH POWER i.LINK 1 POWER switch Press to turn on the player. 2 TIME/TEXT button Each time you press the button, the playing time of the track, the total remaining time on the disc, or TEXT information appears in the display. 3 SACD/CD button Each time

38、you press the button while playing back a hybrid disc, the layer to be played back switches between the HD (Super Audio CD) layer and the CD layer. 4 i.LINK button Each time you press the button, i.LINK function turns on or off. i.LINK indicator Lights up when the i.LINK function is used. 5 Disc tra

39、y Press A OPEN/CLOSE to open/close the disc tray. Front Panel Parts Descriptions 11 SCD-XA9000ES Rear Panel Parts Descriptions 1 ANALOG 5.1CH OUT jacks Connect to an amplifier equipped with the 5.1CH input jacks (Multi-channel amplifier, AV amplifier, etc.) using the audio connecting cords. 2 DIGITA

40、L (CD) OUT COAXIAL connector Connect to an audio component using the coaxial digital cable. 3 DIGITAL (CD) OUT OPTICAL connector Connect to an audio component using an optical digital cable. 4 i.LINK S200 AUDIO OUT jack Connect to STR-DA9000ES/TA-DA9000ES using the i.LINK connecting cord. 5 AC IN te

41、rminal Connect the AC power cord. 6 ANALOG 2CH OUT L/R jacks Connect to an audio component (stereo/2 channel) using the audio connecting cord. Note Only the audio signals of the CD can be output from the DIGITAL (CD) OUT connectors shown in 2 and 3. Those of the Super Audio CD cannot be output throu

42、gh DIGITAL (CD) OUT connectors. When the i.LINK indicator is lit No signal is output from all the other jacks (ANALOG 2CH OUT jacks, ANALOG 5.1CH OUT jacks, PHONES jack, DIGITAL (CD) OUT jacks). ANALOG L LR RR L 5.1CH OUT 2CH OUT OUT OPTICALCOAXIAL CENTER FRONTSURROUNDSUB WOOFER DIGITAL(CD) AC IN AU

43、DIO OUT i.LINK S200 12 SCD-XA9000ES Remote Parts Descriptions CONTINUE SHUFFLE PLAY MODE PROGRAM SACD/CD 123 456 78 10/0 9 TIME/TEXT REPEAT AMS BA CLEAR 10ENTER MODE DISPLAY/ MULTI/2CH INDEX LEVEL ADJ CHECK 1 CONTINUE button Press to resume normal play from Shuffle Play or Program Play. SHUFFLE button Press to select Shuffle Pla