Sony-CDP-CX455-Service-Manual电路原理图.pdf

《Sony-CDP-CX455-Service-Manual电路原理图.pdf》由会员分享，可在线阅读，更多相关《Sony-CDP-CX455-Service-Manual电路原理图.pdf（68页珍藏版）》请在收音机爱好者资料库上搜索。

1、CDP-CX455 US Model Canadian Model AEP Model UK Model SERVICE MANUAL COMPACT DISC PLAYER SPECIFICATIONS Model Name Using Similar MechanismNEW CD Mechanism TypeCDM62-K1BD46A Base Unit TypeBU-K1BD46A Optical Pick-up TypeKSM-213BFN Sony Corporation Home Audio Company Published by Sony Engineering Corpor

2、ation 9-873-947-01 2002D1600-1 2002.04 Ver 1.0 2002. 04 Audio cord (1) Monaural (2P) mini-plug cord (1) (Connecting cord for CONTROL A1II) (supplied for Canadian models only) Remote commander (remote) (1) Size AA (LR6) batteries (2) Compact disc player LaserSemiconductor laser ( = 780 nm) Emission d

3、uration: continuous Laser outputMax 44.6 W* * This output is the value measured at a distance of 200 mm from the objective lens surface on the Optical Pick-up block with 7 mm aperture. Frequency response20 Hz to 20 kHz 0.5 dB Signal-to-noise ratioMore than 108 dB Dynamic rangeMore than 87 dB Harmoni

4、c distortionLess than 0.009% Output LINE OUT DIGITAL OUT (OPTICAL) Jack type Phono jacks Optical output connector Maximum output level 2 V (at 50 kilohms) 18 dBm Load impedance Over 10 kilohms Wave length: 660 nm General Power requirements Power consumption16 W 1 W (at the Power Saving Mode) Dimensi

5、ons (approx.)430 189 537 mm (w/h/d)(17 7 1/2 21 1/4 in.) incl. projecting parts Mass (approx.)8.8 kg (19 lbs 7 oz.) Supplied accessories Design and specifications are subject to change without notice. Where purchased US, Canada Europe Power requirements 120 V AC, 60 Hz 230 V AC, 50/60 Hz RadioFans.C

6、N 收音机爱 好者资料库 2 CDP-CX455 CAUTION Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. Notes on chip component replacement Never reuse a disconnected chip component. Notice that the minus side of a tantalum capacitor

7、 may be damaged by heat. Flexible Circuit Board Repairing Keep the temperature of soldering iron around 270C during repairing. Do not touch the soldering iron on the same conductor of the circuit board (within 3 times). Be careful not to apply force on the conductor when soldering or unsoldering. La

8、ser component in this product is capable of emitting radiation exceeding the limit for Class 1. This appliance is classified as a CLASS 1 LASER product. The CLASS 1 LASER PRODUCT MARKING is located on the rear exterior. The following caution label is located inside of the unit. PARTS No.MODEL MODEL

9、IDENTIFICATION BACK PANEL 4-238-082-0s 4-238-082-1s 4-238-082-2s US CND AEP, UK SAFETY-RELATED COMPONENT WARNING ! COMPONENTS IDENTIFIED BY MARK ! OR DOTTED LINE WITH MARK ! ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE

10、 PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY. ATTENTION AU COMPOSANT AYANT RAPPORT LA SCURIT! LES COMPOSANTS IDENTIFIS PAR UNE MARQUE ! SUR LES DIAGRAMMES SCHMATIQUES ET LA LISTE DES PICES SONT CRITIQUES POUR LA SCURIT DE FONCTIONNEMENT. NE REMPLACER CES COMPOSANT

11、S QUE PAR DES PICES SONY DONT LES NUMROS SONT DONNS DANS CE MANUEL OU DANS LES SUPPLMENTS PUBLIS PAR SONY. SAFETY CHECK-OUT After correcting the original service problem, perform the following safety checks before releasing the set to the customer: Check the antenna terminals, metal trim, “metallize

12、d” knobs, screws, and all other exposed metal parts for AC leakage. Check leakage as described below. LEAKAGE The AC leakage from any exposed metal part to earth Ground and from all exposed metal parts to any exposed metal part having a return to chassis, must not exceed 0.5 mA (500 microampers). Le

13、akage current can be measured by any one of three methods. 1.A commercial leakage tester, such as the Simpson 229 or RCA WT-540A. Follow the manufacturers instructions to use these instruments. 2.A battery-operated AC milliammeter. The Data Precision 245 digital multimeter is suitable for this job.

14、3.Measuring the voltage drop across a resistor by means of a VOM or battery-operated AC voltmeter. The “limit” indication is 0.75 V, so analog meters must have an accurate low-voltage scale. The Simpson 250 and Sanwa SH-63Trd are examples of a passive VOM that is suitable. Nearly all battery operate

15、d digital multimeters that have a 2V AC range are suitable. (See Fig. A) Fig. A. Using an AC voltmeter to check AC leakage. PART NO. 0.15F To Exposed Metal Parts on Set 1.5k AC voltmeter (0.75V) Earth Ground Abbreviation CND : Canadian model RadioFans.CN 收音机爱 好者资料库 3 CDP-CX455 SECTION 1 SERVICE NOTE

16、 NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK OR BASE UNIT The laser diode in the optical pick-up block may suffer electrostatic break-down because of the potential difference generated by the charged electrostatic load, etc. on clothing and the human body. During repair, pay attention to electrostat

17、ic break-down and also use the procedure in the printed matter which is included in the repain parts. The flexible board is easily damaged and should be handled with care. NOTES ON LASER DIODE EMISSION CHECK The laser beam on this model is concentrated so as to be focused on the disc reflective surf

18、ace by the objective lens in the optical pick- up block. Therefore, when checking the laser diode emission, observe from more than 30 cm away from the objective lens. The emission check enables continuous checking of the S curve. LASER DIODE AND FOCUS SEARCH OPERATION CHECK Carry out the “S curve ch

19、eck” in “CD section adjustment” and check that the S curve waveform is output three times. TABLE OF CONTENTS 1. SERVICE NOTE 3 2. GENERAL 6 3. DISASSEMBLY 7 3-1. Case 8 3-2. MAIN Board 8 3-3. TRANS Board 9 3-4. Front Panel Assembly 9 3-5. JOG Board, DISP Board, KEYBOARD Board10 3-6. Cover (PT), Tabl

20、e (400) Assembly 11 3-7. LED Board, Guide (Door)11 3-8. DOOR SW Board 12 3-9. Base (Door Driving) Assembly 13 3-10.Pop-up Assembly 13 3-11.D.MOTOR Board, Motor Assembly (Door) (M603) 14 3-12.T.SENS Board, Holder (Table Sensor 400) 14 3-13.D.SENS (OUT) Board, D.SENS (IN) Board 15 3-14.Back Panel Sect

21、ion 15 3-15.CD Mechanism, Magnet Assembly 16 3-16.LOADING SW Board, LOCK SW Board 17 3-17.CDM Assembly 18 3-18.Motor Assembly (Table) (M601), Motor Assembly (Loading) (M602) 18 3-19.BU Holder 19 3-20.BD Board, Optical Pick-up (KSM-213BFN) 19 4. TEST MODE 20 5. ADJUSTMENTS 25 6. DIAGRAMS 29 6-1. Circ

22、uit Boards Location 29 6-2. Block Diagrams 30 6-3. Printed Wiring Board BD Board 32 6-4. Schematic Diagram BD Board 33 6-5. Printed Wiring Board MAIN Board 34 6-6. Schematic Diagram MAIN Board (1/2) 35 6-7. Schematic Diagram MAIN Board (2/2) 36 6-8. Printed Wiring Board Sensor Section 37 6-9. Schema

23、tic Diagram Sensor Section 37 6-10.Printed Wiring Board Display Section 38 6-11.Schematic Diagram Display Section 39 6-12.Printed Wiring Board JOG Board 40 6-13.Schematic Diagram JOG Board 41 6-14.Printed Wiring Board Power Section 42 6-15.Schematic Diagram Power Section 43 6-16.IC Block Diagrams 44

24、 6-17.IC Pin Function Descriptions 46 7. EXPLODED VIEWS 50 7-1. Case Section 50 7-2. Chassis Section 1 51 7-3. Chassis Section 2 52 7-4. Front Panel Section 53 7-5. Mechanism Section 1 (CDM62-K1BD46A) 54 7-6. Mechanism Section 2 (CDM62-K1BD46A) 55 7-7. Mechanism Section 3 (CDM62-K1BD46A) 56 7-8. Mec

25、hanism Section 4 (CDM62-K1BD46A) 57 7-9. Optical Pick-up Section (BU-K1BD46A) 58 8. ELECTRICAL PARTS LIST59 4 CDP-CX455 CD-TEXT TEST DISC This unit is able to display the TEXT data (character information) written in the CD on its fluorescent indicator tube. The CD-TEXT TEST DISC (TGCS-313:J-2501-126

26、-A) is used for checking the display. To check, perform the following procedure. Checking Method: 1.Turn ON the power, set the disc on the disc table with the side labeled as “test disc” as the right side, close the front cover, and chuck the disc. 2.The following will be displayed on the fluorescen

27、t indicator tube. (The display switches each time the DISPLAY button is pressed.) Display : CD TEXT Test Disc (Album Title) 3.Press the button and play back the disc. 4.The following will be displayed on the fluorescent indicator tube. (If nothing is displayed, press the DISPLAY button.) Display : 1

28、kHz/0 dB/ L ?(38h to 3Fh) A B C D E F G(40h to 47h) H I J K L MNO(48h to 4Fh) P QR S T U VW(50h to 57h) X Y Z _(58h to 5Fh) a b c d e f g(60h to 67h) h i j k l m n o(68h to 6Fh) p q r s t u v w(70h to 77h) x y z I (78h to 7Fh) i (A0h to A7h) 8859-1 C PR (A8h to AFh) 23 (B0h to B7h) 1 (B8h to BFh) (C

29、0h to C7h) (C8h to CFh) D (D0h to D7h) Y(D8h to DFh) (E0h to E7h) (E8h to EFh) (F0h to F7h) y(F8h to FFh) No.66 No.67 to No.99 1 4 1 2 3 4 1 4 1 2 3 4 Table 2: CD-TEXT TEST DISC Recorded Contents and Display (In this unit, some special characters cannot be displayed. This is no a fault.) 6 CDP-CX455

30、 LOCATION OF PARTS AND CONTROLS SECTION 2 GENERAL Front Panel 1 1/u (power) button 2 STANDBY indicator 3 Display window 4 CONTINUE button 5 SHUFFLE button 6 PROGRAM button 7 REPEAT button 8 DISPLAY button 9 Front cover q; OPEN/CLOSE button qa DISC EJECT button qs HISTORY button and indicator qd MENU

31、/NO button qf +100 button qg YES button qh DISC/ALBUM/CHARACTER/PUSH ENTER knob and button qj CHECK button qk CLEAR button ql NAME SEARCH button w; ALBUM SELECT button and indicator wa FADER button ws X-FADE button wd NO DELAY button wf MEGA CONTROL button and indicator wg l AMS L /PUSH ENTER knob a

32、nd button wh p (stop) button wj (play) button and indicator wk P (pause) button and indicator wl ARTIST MODE button and indicator e; TOP ARTIST 4 button and indicator ea TOP ARTIST 3 button and indicator es TOP ARTIST 2 button and indicator ed TOP ARTIST 1 button and indicator ef TIME button eg TOP

33、ARTIST 8 button and indicator eh TOP ARTIST 7 button and indicator ej TOP ARTIST 6 button and indicator ek TOP ARTIST 5 button and indicator el KEYBOARD jack r; TIMER OFF/PLAY switch 4 edwles 765 eae;ekelefejeheg 9q;qaqsqdqfqg8 qh qjw;qk ql wa wg wfws wd wkwjwh 2 3 1 r; 7 CDP-CX455 SECTION 3 DISASSE

34、MBLY MAIN BOARD SET JOG BOARD, DISP BOARD, KEYBOARD BOARD FRONT PANEL ASSEMBLY CASE LED BOARD, GUIDE (DOOR) COVER (PT), TABLE (400) ASSEMBLY BASE (DOOR DRIVING) ASSEMBLY D. MOTOR BOARD, MOTOR ASSEMBLY (DOOR) (M603) BACK PANEL SECTIONTRANS BOARD CD MECHANISM, MAGNET ASSEMBLY DOOR SW BOARD POP-UP ASSE

35、MBLY D. SENS (OUT) BOARD, D. SENS (IN) BOARD T. SENS BOARD, HOLDER (TABLE SENSOR 400) CDM ASSEMBLY BU HOLDER LOADING SW BOARD, LOCK SW BOARD BD BOARD, OPTICAL PICK-UP (KSM-213BFN) MOTOR ASSEMBLY (TABLE) (M601), MOTOR ASSEMBLY (LOADING) (M602) 8 CDP-CX455 Note : Follow the disassembly procedure in th

36、e numerical order given. 3-1. Case 2 two screws (case 3 screw) 3 two screws (case 3 screw) 1 three screws (case 3 screw) 4 two screws (case 3 screw) 5 case qs two screws (BVTP 3 8) qg bracket (R) 2 connector (CN901) 1 three connectors (CN503, CN801, CN903) 3 connector (CNP902) 6 connector (CNP504) 5

37、 flat type wire (CN502)(17 core) 4 two connectors (CN505, CN506) 7 three screws (BVTP 3 8) 8 four screws (BVTP 3 8) 0 MAIN board 9 flat type wire (CN501)(31 core) qa two screws (BVTP 3 8) qf bracket (L) qd 3-2. MAIN Board 9 CDP-CX455 5 screw (BVTP 3 8) 6 bracket (PT) 4 connector (CN601) 1 connector

38、(CN991) 3 connector (CN603) 2 connector (CN602) A A 7 two screws (PTTWH 3 6) 8 TRANS board 2 3 connector (CNP503) 5 two screws (BVTP 3 8) 4 screw (BVTP 3 8) 6 three screws (BVTP 3 8) 7 remove the claw 8 remove the claw 9 front panel assembly 1 3-3. TRANS Board 3-4. Front Panel Assembly 10 CDP-CX455

39、3-5. JOG Board, DISP Board, KEYBOARD Board qs remove two solderings. 1 knob (AMS) 2 knob (disc) 3 four screws (BVTP 2.6 x 8) 4 bracket (case) assembly 5 eleven screws (BVTP 2.6 x 8) 7 eight screws (BVTP 2.6 x 8) qa two screws (BVTP 2.6 x 8) 8 DISP board 9 flat type wire (17 core) 0 knob (timer) 6 JO

40、G board qf KEYBOARD board qd bracket (keyboard) 11 CDP-CX455 3 screw (BVTP 3 16) 4 guide (door) 5 table (400) assembly 6 washer Note during re-assembling When re-assembling, align the positions as shown. 1 two screws (BVTP 3 8) 2 cover (PT) 1 screw (BVTP 3 x 8) 6 window (internal illumination) 2 LED

41、 board 3 5 4 7 guide (door) 3-6. Cover (PT), Table (400) Assembly 3-7. LED Board, Guide (Door) 12 CDP-CX455 5 two screws (BVTP 2.6 8) 3 screw (PTPWH 2.6 8)1 screw (PTPWH 2.6 8) 1 Move the slider (pop-up) and the lever (pu joint) fully in the direction of the arrow A. 2 Install the gear (cam) in the

42、direction shown in the illustration and rotate it fully in the direction of the arrow B. 3 When the gear (cam) happens to go too deep, return it to the original position in the direction of the arrow C. 4 gear (B) 2 gear (cam) 6 DOOR SW board C B Alever (pu joint) two rotary switches slider (pop-up)

43、 gear (cam) DOOR SW board The levers of the two rotary switches on the D. SW board are shown in the illustration below. Precaution during the gear (cam) installation 3-8. DOOR SW Board 13 CDP-CX455 3-9. Base (Door Driving) Assembly 1 connector (CN602) 2 three screws (BVTP 3 8) 3 cover (table) 4 door

44、 assembly 5 two screws (BVTP 3 8) 6 eight screws (BVTP 3 8) 7 base (door driving) assembly 1 screw (PTPWH 3 6) 2 step screw 3 pop-up assembly 3-10. Pop-up Assembly 14 CDP-CX455 1 belt 3 D.MOTOR board 5 door motor assembly 4 remove two solderings. 2 two screws (BVTP 3 8) (M603) 1 four screws (PTPWH 3

45、 6) 4 T.SENS board 5 screw (PTTWH 3 6) 2 connector (CN83) 3 two connectors (CN81,CN82) 6 three claws 7 holder (table sensor 400) 3-11. D.MOTOR Board, Motor Assembly (Door) (M603) 3-12. T.SENS Board, Holder (Table Sensor 400) 15 CDP-CX455 3-13. D.SENS (OUT) Board, D.SENS (IN) Board 4 screw (PSW 3 8)

46、5 D.SENS (OUT) board 1 screw (PTTWH 3 6) 7 D.SENS (IN) board 2 two step screws (T1) 3 bracket (sensor 400) 6 screw (PTTWH 3 6) 1 nine screws (BVTP 3 8) 2 cover (CDM) 3 three screws (BVTP 3 8) 4 bracket (CDM) 5 6 connector (CN991) 7 four screws (BVTP 3 8) 8 back panel section flat cable clamp 3-14. B

47、ack Panel Section 16 CDP-CX455 3-15. CD Mechanism, Magnet Assembly 2 three screws (BVTP 3 8) 1 three screws (BVTP 3 8) 3 bracket (top 400) 4 magnet assembly 5 washer 6 spring 7 CD mechanism 8 washer Note during re-assembling When re-assembling, align the positions as shown. 17 CDP-CX455 A A B B claw

48、s 1 rotate the pulley (400) in the direction of the arrow fully. 3 rotate the pulley (400) in the direction of the arrow fully. 2 screw (BVTP3 8) 5 tapping screw 4 belt 8 screw (BVTP 3 8) 0 screw (BVTP 2.6 8) qa LOADING SW board 9 LOCK SW board 7 gear (center) 6 pulley (400) Note during re-assemblin

49、g When re-assembling the LOADING SW board and LOCK SW boards, align the leads position as shown. LOADING SW board LOCK SW board Leads position 3-16. LOADING SW Board, LOCK SW Board 18 CDP-CX455 1 connector (CN603) 4 four screws (BVTP 3 8) 3 screw (PSW 3 8) 5 seven screws (BVTP 3 8) 6 CDM assembly 2 connector (CN601) 4 motor as