Philips-MCD-759-D-Service-Manual电路原理图.pdf

《Philips-MCD-759-D-Service-Manual电路原理图.pdf》由会员分享，可在线阅读，更多相关《Philips-MCD-759-D-Service-Manual电路原理图.pdf（60页珍藏版）》请在收音机爱好者资料库上搜索。

1、Version 1.0MCD759D3141 785 31970DVD Micro Theatreall versions Published by LX 0728 Service Audio Subject to modification Copyright 2007 Philips Consumer Electronics B.V. Eindhoven, The NetherlandsAll rights reserved. No part of this publication may be reproduced, stored in a retrievalsystem or trans

2、mitted, in any form or by any means, electronic, mechanical, photocopying,or otherwise without the prior permission of Philips.Service Aids .1-1CD Playability Check .1-2.1-4Technical specification .2-1Service tools .2-1Service measurement setup .2-2Disassembly diagram.3-1.3-6Software version check a

3、nd upgrading .4-1Block diagram .5-1Wiring diagram .6-1VFD Board circuit diagram .7-1 layout diagram .7-2AMP Boardcircuit diagram .8-1layout diagram .8-2.8-3Tuner Board circuit diagram. .9-1layout diagram .9-2Power Boardcircuit diagram. .10-1layout diagram .10-2.10-3DVD MPEG Boardcircuit diagram. . 1

4、1-1.11-5layout diagram .11-6CPU Board circuit diagram. .12-1layout diagram .12-2.12-3Spare partslist.13-1.13-2Supplier Original partslistTABLE OF CONTENTS1-1Service Tools:Universal Torx driver holder .4822 395 91019Torx bit T10 150mm .4822 395 50456Torx driver set T6-T20 .4822 395 50145Torx driver T

5、10 extended .4822 395 50423Compact Disc:SBC426/426A Test disc 5 + 5A .4822 397 30096SBC442 Audio Burn-in test disc 1kHz .4822 397 30155SBC429 Audio Signals disc .4822 397 30184Dolby Pro-logic Test Disc .4822 395 10216SERVICE AIDSGB WARNINGAll ICs and many other semi-conductors aresusceptible to elec

6、trostatic discharges (ESD).Careless handling during repair can reduce lifedrastically.When repairing, make sure that you areconnected with the same potential as the massof the set via a wrist wrap with resistance.Keep components and tools also at thispotential.ESDCLASS 1LASER PRODUCTGBSafety regulat

7、ions require that the set be restored to its originalcondition and that parts which are identical with those specified,be usedSafety components are marked by the symbol !.Lead freeSet remains closed!Standard repair procedureNYPlay a CD for at least 10 minutesYplayabilityok ?Nplayabilityok ?add Info

8、for customer“SET OK“playabilityok ?YNcheck playabilityNYplayabilityok ?check playabilitycheck playabilityEYE-Patternok ?NYcheck “EYE-Pattern“replace CD DriveLaser currentok ?NYcheck Laser currentCD Drive offsetsok ?NYcheck CD Drive offsetsclean the lenscheck playabilityreturn setCustomer complaint“C

9、D related problem“return setreturn setreplace CD Drivereturn setreplace CD Drivereturn setreplace Signal Processorreturn set“fast“ lens cleaning1234567For flap loaders (= access to CD drive possible) cleaning method 4 is recommended1 - 7 For description - see following pagesCD PLAYABILITY CHECK1-21P

10、LAYABILITY CHECKFor sets which are compatible with CD-RW discsuse CD-RW Printed Audio Disc.7104 099 96611TR 3 (Fingerprint)TR 8 (600 Black dot) maximum at 01:00 playback of these two tracks without audible disturbanceplaying time for: Fingerprint 10secondsBlack dot from 00:50 to 01:10 jump forward/b

11、ackward (search) within a reasonable timeFor all other sets use CD-DA SBC 444A.4822 397 30245TR 14 (600 Black dot) maximum at 01:15TR 19 (Fingerprint)TR 10 (1000 wedge) playback of all these tracks without audible disturbanceplaying time for: 1000 wedge 10secondsFingerprint 10secondsBlack dot from 0

12、1:05 to 01:25 jump forward/backward (search) within a reasonable time2CUSTOMER INFORMATIONIt is proposed to add an addendum sheet to the set whichinforms the customer that the set has been checkedcarefully - but no fault was found.The problem was obviously caused by a scratched, dirty orcopy-protect

13、ed CD. In case problems remain, the customeris requested to contact the workshop directly. The lens cleaning (method 3) should be mentioned in theaddendum sheet.The final wording in national language as well as the printingis under responsibility of the Regional Service Organizations.3FAST LENS CLEA

14、NING (dry brush)Use lens cleaning CDSBC AC300.9082 100 00043Insert the lens cleaning CD, press PLAY and follow thevoice guides instructions on the CD.4LIQUID LENS CLEANINGBecause the material of the lens is synthetic and coatedwith a special anti-reflectivity layer, cleaning must be donewith a non-a

15、ggressive cleaning fluid. It is advised to use“Cleaning Solvent B4-No2”, available with codenumber4822 389 10026.The actuator is a very precise mechanical component andmay not be damaged in order to guarantee its full function.Clean the lens gently (dont press too hard) with a soft andclean cotton b

16、ud moistened with the special lens cleaner.The direction of cleaning must be in the way as indicated inthe picture below.Before touching the lens it is advised to clean thesurface of the lens by blowing clean air over it.This to avoid that little particles make scratches onthe lens.CD PLAYABILITY CH

17、ECK1-35EYE-PATTERN SIGNAL JITTER MEASUREMENTMeasure the signal on the input of the Signal processorusing an analog oscilloscope. Please find the exactmeasuring point in your Service Manual.See below examples of the signal. Amplitude should read atleast 700mVpp using SBC444A.goodbadIf the oscilloscop

18、e shows a signal like the bad one, and/orthe amplitude decreases within 1 minute - the CD drive hasto be replaced.6CD DRIVE LASER CURRENT MEASUREMENTThe laser current can be measured as a voltage drop on aresistor. The resistor is marked in every Service Manual.The value depends on the type of CD dr

19、ive.typical value most probably defectVAMxxxx : 150-230mV 350mVMCDxx : 170-230mV 300mVDA1x : 210-250mV 350mVDA2x : 175-200mV 250mVUse SBC444A (CD-DA) for measurement.7CD DRIVE OFFSET MEASUREMENTThe photodiodes of the CD-drive may have an offset. Theseoffsets have to be compensated by the signal proc

20、essor.High offsets can lead to poor playability of some CDs(skipping tracks).To measure the offset values, start the Service TestProgram - section “Focus Test” without a CD.The offsets can be measured with a DC Millivoltmeterdirectly on the connector (see drawing below). Pinnumbering varies from dri

21、ve to drive.The values from diode A-D should read 010mV.Diodes E and F are less critical.If one of the offsets is higher than 10mV the CD drive hasto be replaced. Otherwise replace the Signal Processor.Sanyo DA12T3CD DriveAAFCBECDEVCCBVREFFD9101112131415161800+5V_HFVrefCD10ADEBCFGND 8EDABCFLaser pow

22、er control100n2878470n287638211R1K3823288033p+5VBC807-407879381747R38204R747R38191n28792877 47u1847811-ALM358D3210K382247R38182841 100n47n2869+5V_HFLASER DIODEU 250mV-Laser damaged !4,6V3V3,3V3,9V2V0,17V0,17VSanyoDA12T3HF-AmplifierD3D2D1Drive detection680R390539033K3BC847B787747n28181K53902574216364

23、891011470R3893+3.3V2K23908 10K3923BC847B7878BC847B78764n728133896100R220u28852881560p47n2887560R39012883470n28174u73n328143898220R389527K470n2884+3.3V3909820R3907100R392033K3897288282p3K339042K738993906470R+5V_HFHFINVrefCD10100p2815281622nLDONto 3826,3827VREF GEVDDA1VRINVSSA1ISLICELDOND1D2D3D4HFINHF

24、REFIREFCD_DA: 0V / CD_RW: 3V (A-D)800mVppTB = 0.5s/divEYE-PATTERN1,8V1,2V2,4V2,6V0,65VCD PLAYABILITY CHECK1-42 - 1TECHNICAL SPECIFICATIONSSYSTEMPower supply . 120 V / 60 HzTotal output power . 480WL, R Front . 50Wx2 at 1KHz, THD 1%L, R Rear . 50Wx2 at 1KHz, THD 1%Center .140Wx1 at 1KHz, THD 1%Subwoo

25、fer . 140Wx1 at 63Hz, THD 1%AUX input sensitivity . null 550mVChannel Separation .null 40dBDistortion . 0.7%DVDFrequency response . 100Hz-20kHz (2dB)Video output .1 VP-PHorizontal definition.null 500 (TV)Dimensions . 232 (W) x 75.5 (H) x 227 (D) mmWeight . 1.75 kgAMPLIFIERRated output power (THD = 1

26、0%) . 4x75W (4null)+2x150W (8null)Frequency response . 100Hz-20kHz (2dB)S/N Ratio .null 60dBLoaded impedance . 8 null/4 nullDimensions . 232 (W) x 75.5 (H) x 235 (D) mmWeight . 3.8kgTUNERFM Frequency range. 87.5-108 MHzFM Noise limit sensitivity . null 20 V/MFM S/N .null 46dBAM Frequency range . 520

27、-1710 kHzAM Noise limit sensitivity.null 3.0 mV/mAM S/N .null 40dBSPEAKERSFront SpeakersSystem . 2-way shieldedImpedance. 4 nullSpeaker drivers. 2x4” woofer, ribbon twDimensions (w x h x d) . 223 mm x 1012 mm x 223 mmWeight . 12.95 kgCenter SpeakerSystem . 2-way shieldedImpedance. 8 nullSpeaker driv

28、ers. 4” woofer, 2” twDimensions (w x h x d) . 392mm x 144 mm x 67 mmWeight . 2.45 kgSurround SpeakersSystem . 2-way shieldedImpedance. 4 nullSpeaker drivers. 1 x 3” woofer, PiezeDimensions (w x h x d) . 144 mm x 250 mm x 50 mmWeight . 2.6 kgSUBWOOFERSubwoofer (not magnetically shielded design). 8”Im

29、pedance. 8 nullDimensions (w x h x d) . 255 mm x 336 mm x 426 mmWeight . 12.6 kgREMOTEDistance . 6mAngle . 300Specifications subject to change withoutprior notice2 - 2SERVICE MEASUREMENTBandpass250Hz-15kHze.g. 7122 707 48001LF Voltmetere.g. PM2534DUTRF Generator e.g. PM5326S/N and distortion metere.

30、g. Sound Technology ST1700BTuner FWUse a bandpass filter to eliminate hum (50Hz, 100Hz) and disturbance from the pilottone (19kHz, 38kHzRi=50Bandpass250Hz-15kHze.g. 7122 707 48001LF Voltmetere.g. PM2534DUTS/N and distortion metere.g. Sound Technology ST1700BFrame aeriale.g. 7122 707 89001Tuner AM (M

31、W,LW)To avoid atmospheric interference all AM-measurements have to be carried out in a Faradays cage.Use a bandpass filter (or at least a high pass filter with 250kHz) to eliminate hum (50Hz, 100Hz).RF Generator e.g. PM5326Ri=50LRLEVEL METERe.g. Sennheiser UPM550with FF-filterS/N and distortion mete

32、re.g. Sound Technology ST1700BDUTCD RECORDERUse Audio Signal Disc SBC429 4822 397 30184(replaces test disc 3)Use Universal Test Cassette Fe SBC420 4822 397 LRLEVEL METERe.g. Sennheiser UPM550with FF-filterS/N and distortion e.g. Sound Technology ST1700BDUTLF Generator e.g. PM5110Ri=50DVD part A、 Rem

33、ove bottom cover B、 Remove top cover and screws 3 10PTH（ 4PCS） 3 8FT（ 2PCS） A1、 Remove screws 2.5 7PWMTT（ 3PCS） ， 2.6 5PWMTT（ 7PCS） B1.Remove screws 3 10FA（ 1PCS） C、 Remove around of side panel and screws 3 6BTH（ 4PCS） 3 6FMTT（ 2PCS） C1、 Remove screws 3 4FMTT（ 4PCS） ABB1CC1Disassembly diagramD. Remo

34、ve mechanism and screws 3 10PWA（ 2PCS） 3 8PWMTT（ 2PCS） E、 Remove back panel and screws 3 10FA（ 7PCS） 3 6FMTT（ 1PC） F. Remove motor and side panel G、 Remove CPU board, MPEG, IC and loosen screws And loosen screws 3 6FT（ 2PCS） 3 10BT（ 2PCS） 3 6PM（ 6PCS） 3 4FMTT（ 1PC） DEFGDisassembly diagramH、 Remove s