Philips-DVP-3254-K-Service-Manual电路原理图.pdf

《Philips-DVP-3254-K-Service-Manual电路原理图.pdf》由会员分享，可在线阅读，更多相关《Philips-DVP-3254-K-Service-Manual电路原理图.pdf（38页珍藏版）》请在收音机爱好者资料库上搜索。

1、3139 785 33381 TABLE OF CONTENTS Page Version 1.1 Service Manual DVP3254K DVP3254K/55 Technical Specifications.1-2 . Safety Instruction, Warning 50/60 Hz Power consumption to check the File Name. Note: It is required capital letter for the File System name. 2) Burn the data onto a blank CDR A. Proce

2、dure for software upgrade: 1) Power on the set and insert the prepared Upgrade CDR. 2) The set will starts reading disc & response with the following display TV screen: Upgrade File DETECTED Upgrade? Press Play TO START. 3) Press button to confirm, then screen will display : Files coping UPGRADING 4

3、) The upgraded tray will automatically open when files coping complete, then take out the disc. 5) About 1 minute later, the trace will automatically close when upgrading complete. B. Read out the software versions to confirm upgrading 1) Power on the set and press button on the remote control. 2) P

4、ress button. The software version and other information are display on the TV screen as follows: Version XX.XX.XX.XX (Main version) SUB-VER XX.XX.XX.XX (software version of application software) 8032 XX.XX.XX.XX Servo XX.XX.XX.XX (software version of Servo) RISC XX.XX.XX.XX DSP XX.XX.XX.XX Region Co

5、de X 3-1 Caution: The set must not be power off during upgrading, Otherwise the Main board will be damaged entirely. 4-1 Spindle motor does not move Yes Yes No No No No Yes Check whether “M5V” (+5V) voltage is normal. Correct connection Check the M5V power supply Check/Replace Q5,Q6,Q7,Q8. Check/ Re

6、place U1. Check opu focus 1. Check U1 25pin FOCUS_PWM signals 2.If there are F+, F-, T+ and T- signals output from U2. Check/Replace the loader Yes Yes No Go Check whether laser voltage (1.9V for CD & 2.4V for DVD) on L9 and L10 Check the FFC connection between 24P and the loader. 1.Whether voltage

7、on pin 23 of U1 varies between 0 and 3.3V (3.3V for CD and 0V for DVD), 2.Whether peripheral components are eroded or badly soldered. Trouble shooting chart Motor no move FOCUS_PWN waveform 4-2 The power can not be on or off Go Ye s Yes No No The power cant be on or off Yes Repair the power board Ch

8、eck the power supply on the power board is normal. Check/Correct connection Whether the connection to K301 is broken. Correct the connection Replace U1. No No Yes Yes Check if the XS301 on the front board to XP5 on the decoder board is in good contact. Whether there is 0V and 3.3V voltage difference

9、 on Pin 106 PCON of U1. Trouble shooting chart 4-3 All output voltages on the power board is 0V or deviated.No No No Yes No U1(PIN 8 - Drain waveform) Replace F1 Replace C1&C2 if D1, D2, D3, D4 are normal. Check/ replace U1. Check whether U1 are eroded. All output voltages on the power board is 0V o

10、r deviated Check whether there is 300V on C1 or C2. Check whether 100KHz oscillating signal on Pin6 of U1 Check if +5V and +12V are short. Check whether the components in the short-circuit voltage are defected or eroded. Yes Yes Yes Yes U1(PIN 3 - RC waveform) Trouble shooting chart Check whether F1

11、 is blown4-4Disc cannot be read. No Yes No Yes No Yes Yes No No Yes Disc cannot be read. Check the loaded circuit 1.Check voltage on pin 23 of U1 varies between 0 and 3.3V: 3.3V for CD 0V for DVD 2.Check whether peripheral components are eroded or defect Check the FFC connection between 24P and the

12、loader. Check U1 and peripheral components Re-solder or replace the defective parts Check the connection between U1 Correct connection Replace U1 or loader. Yes Check whether there is laser voltage (1.9V for CD and 2.4V for DVD) on L9 and L10. Check if there is RFO signal on pin17 of XP2. (The normal RFO signal is a clear reticulated wave) Trouble shooting chart Check U1, U2, and peripheral components are eroded or badly soldered.