Philips-FWC-399-Service-Manual电路原理图.pdf

《Philips-FWC-399-Service-Manual电路原理图.pdf》由会员分享，可在线阅读，更多相关《Philips-FWC-399-Service-Manual电路原理图.pdf（76页珍藏版）》请在收音机爱好者资料库上搜索。

1、CLASS 1LASER PRODUCTCOMPACTDIGITAL AUDIOService ManualServiceServiceServiceFW-C399/21/21M/22/37TABLE OF CONTENTSPageLocation of pc boards fr Reparaturen sind Original-Ersatzteile zu verwenden.ILe norme di sicurezza esigono che lapparecchio venga rimessonelle condizioni originali e che siano utilizza

2、ti i pezzi di ricambioidentici a quelli specificati.“After servicing and before returning set to customer perform aleakage current measurement test from all exposed metal parts toearth ground to assure no shock hazard exist. The leakage currentmust not exceed 0.5mA.“CLASS 1LASER PRODUCT3122 110 0342

3、0GB Warning !Invisible laser radiation when open.Avoid direct exposure to beam.S Varning !Osynlig laserstrlning nr apparaten r ppnad och sprrenr urkopplad. Betrakta ej strlen.SF Varoitus !Avatussa laitteessa ja suojalukituksen ohitettaessa olet alttiinankymttmlle laseristeilylle. l katso steeseen!DK

4、 Advarse !Usynlig laserstrling ved bning nr sikkerhedsafbrydere erude af funktion. Undg udsaettelse for strling.2-1 2-1DISMANTLING INSTRUCTIONSDismantling of the Cassette Cover1) Loosen the 4 screws, slide Cover top (pos 255) towardsthe rear and remove it upwards.2) Loosen 3 screws, slide the Panel

5、right (pos 254) towardsthe rear and remove it outwards. Do likewise for the Panelleft (pos 253).3) Push the gear slowly towards the front as shown in figureDismantling the 3CDC Module and Tuner Board3 until the CDC tray starts to move out of the Front Cabinet(pos 101). The CDC tray is now disengaged

6、 and can bepulled out completely.4) Remove the Cover Tray (pos 106) as shown in figure 4.5) Loosen 4 screws A to remove the CDC Module (pos 1105)as shown in figure 3.6) Loosen 3 screws N (see figure 10) on the Panel Rear (pos256) and release 2 catches C1 to remove the Tuner Board.3. Lift up and out1

7、. Place screw driver(flat side) betweenthe cover Button pressed?2;Button pressed?9Button pressed?DISPLAYTESTDisplay shows Fig. 2and selected LEDs on(see note 2)Display shows Fig. 1and selected LEDs on(see note 1)Figure 1Figure 2note 2 : Only DISC 2, TUNER, AUX, DSC, VEC & MAX SOUND are on.note 1 : A

8、ll LEDs are on except ECO POWER.Table 2Error codeE1000E1001E1002E1003E1005E1006E1007E1008E1020E1070E1071E1079Error DescriptionFocus ErrorTriggered when the focus could not be found within a certain time when starting up the CDor when the focus is lost for a certain time during play.Radial ErrorTrigg

9、ered when the radial servo is off-track for a certain time during play.Sledge In ErrorThe sledge did not reach its inner position (inner-switch is still close) before approximately6 Sec. have passed by. Inner-switch or sledge motor problem.Sledge Out ErrorThe sledge did not come out of its inner pos

10、ition (inner-switch is still open) before approximately250 mSec. have passed by. Inner-switch or sledge motor problem.Jump-offtrack errorTriggered in normal play when the jump destination could not be found within a certain time.When this error occurred, software will try to recover by initiating th

11、e jump command again.If it is recoverable, the disc will continue to play.Subcode ErrorTriggered when a new subcode was missing for a certain time during play.PLL ErrorThe Phase Lock Loop could not lock within a certain time.Turntable Motor ErrorGenerated when the CD could not reached 75% of speed d

12、uring startup within a certain time.Discmotor problem.Focus Search ErrorThe focus point has not been found within a certain time.This happens when the carousel switch is defective and closed all the time, or when thecarousel is blocked when it is located exactly at a disc position.This happens when

13、the carousel switch is defective and does not closed electrically, or whenthe carousel is blocked in between two disc positions. The time-out is approximately 5 Sec.The drawer could not open or enter the inside position and is opening again. This happen whenthe drawer is blocked and cannot go fully

14、inside or when the drawer switch is defective and doesnot close.To start service test programhold P & AUXdepressed whileplugging in the mains cordDisplay shows theROM version *“S-Vyy“(Main menu)S refers to Service Mode.V refers to Version.yy refers to Software version number of Processor.(Counting up from 01 to 99)SERVICE TEST PROGRAMMini 2002 FW-C399 Dated: wk141