Kenwood-XXV-03-A-Service-Manual电路原理图.pdf
《Kenwood-XXV-03-A-Service-Manual电路原理图.pdf》由会员分享,可在线阅读,更多相关《Kenwood-XXV-03-A-Service-Manual电路原理图.pdf(24页珍藏版)》请在收音机爱好者资料库上搜索。
1、 2005-4 PRINTED IN JAPANB53-0282-00 (N)1553POWER AMPLIFIERXXV-03ASERVICE MANUAL* Depends on the destination. Refer to the parts list.VOLTFANCURRTEMPMENU012345 6789252525RESETREMOTETO H/UID NUMBERPOWER INHeat sink(F01-1795-01)Screw(N07-0003-08)Screw(N09-4214-08)Fuse (25A)(F52-0014-05)* Cover(F07-xxxx
2、-xx)Screw & Wrench key set(N99-1770-15)Screw set(N99-1577-15)Accessory(W01-1606-05)Subwoofer Power AmplifierSubwooferPowerAmplifier“eXcelon“ is not printedon European Model“eXcelon“ is not printedon European Model* Dressing plate(A21-xxxx-xx)XXV-03A2BLOCK DIAGRAM PREAMPLIFIER UNIT (X08-4230-10)Ref.
3、No Application / Function Operation / Condition / CompatibilityIC1 ISF Cutting super-low range of audio signalIC2 (1/43/4) BRF Cutting bandwidth of audio signalIC2 (4/4) INV Phase reversal of audio signalIC3 OP amplifier Voltage amplification, BufferIC4 E-VOL Electronic volumeIC5 LPF Cutting high-ra
4、nge of audio signalIC6 LCD driver LCD driver AUDIO UNIT (X09-5930-10)Ref. No Application / Function Operation / Condition / CompatibilityIC1 Isolation amplifier Prevent noise from GND potential differenceIC2 (1/2) Triangular wave generation Reference signal for digitizing analog signalIC2 (2/2) Erro
5、r amplifier Error is compensated by the feedback from outputIC3 Comparator, Triangular wave generation Digitizing by comparison of analog signal and triangular waveCOMPONENTS DESCRIPTIONLINELINE INAMPCONT.DRIVERLCDCOMPARATORDEADTIMETRIANGLEWAVELOADOVERDRIVERMUTEDCOFFSETDET.CURRENTINPUTVOLTAGECONTROL
6、FANOVERVOLTAGEMEASURE DET.SWITCHPOWER15VAVRAVR+5V+5VSWITCHSWITCHACCRESSROMCORRECTICRESETTHERMALPROTECTBUFFERI2CVOLTAGEDET.DOWNP CONDET.AMPMUTECOMPARATORISOLATORCONTDET. DET.ISO I.F.S B.R.F INVL.P.FLCDIC4IC3IC3IC5IC2 IC2IC1ED1IC6IC1Q10 IC2,3 IC4,5IC2Q9Q52-557828,37-40,42-45,48-51Q15,18,19,21,22,27,IC
7、6Q73,IC16Q1-4IC15IC11Q20 84,110Q106-108IC13Q80 IC14 Q63 Q66Q62D.D CONu-COMQ83IC1029,30,Q25,26,SP OUTP CONBATTGNDOUTto H/UREMOTEINDFAN15/25Hz FREQON/OFF OFF/6/12 NOR/REVON/OFFLEVELLED FANAVR 5V SW5V 15VFREQBACKLIGHTD PWR(X08-4230-10)(X09-5930-10)XXV-03A3Ref. No Application / Function Operation / Cond
8、ition / CompatibilityIC4,5 NAND D class section reverse wave, deadtime, generation and rectificationIC6 Comparator Short circuit detection of SP outputIC7 Signal amplification For SP output short-circuit detection, send the output to comparatorIC10 Element operation control Communication, display, p
9、rotection, etc. controlIC11 Reset Reset signal is output when voltage goes below standard voltageIC13 DC/DC converterVoltage on secondary side, which produces the drive signal for switchingelement, will be limited to below standard voltageIC14 Signal amplification To have com display current value,
10、amplify potential differences of GNDIC15 Bi-directional buffer Send/Receive data and clock between AMPIC16 Comparator Receive from H/U data and clockQ1,2,5,7 Digital signal transmission Send LX-REQ-M signal to H/UQ3,4,6,8 Digital signal transmission Send LX-DATA-S signal to H/UQ9 Mute Mute drive sig
11、nal generationQ10 Mute Turn audio signal OFFQ15,18,19,21,22,27,Signal amplification, switching D class section voltage or current amplificationQ28,3740,4245Q16,17 Voltage control Match the beginning of the fall to +15V when -15V power supply is OFFQ20 Voltage control 5V power supply ON/OFFQ23,24,35,
12、36,41,83 Voltage control Fan voltage ON/OFF and limiting over voltageQ25,29,84 AVR +15VQ26,30,110 AVR -15VQ31,33,46,109 Voltage control D class section predrive stage power supply ON/OFFQ47 AVR D class section first stage supplementary power supplyQ52-55 Voltage current converter Over current detect
13、ion when SP is shortedQ57,58,60,61,Switching DC/DC converter switchingQ64,65,6770Q59,63 Voltage control In order to have com display voltage value, send voltage to it only when 5V SW ONQ62 Voltage detection Pcon detectionQ66 Voltage detection Pcon over voltage detectionQ71,72 Waveform shaping For SP
14、 output short-circuit detection, send the output to comparatorQ73,78 Voltage detection DC detection of outputQ74-77 Current amplification Switching FET drive current amplificationQ79,80 Voltage control DC/DC converter power supply ON/OFFQ81,82 Voltage control DC/DC converter drive waveform ON/OFFQ88
15、,89,98,99 Voltage control 5L digital signal receptionQ95,96 Voltage control When Comm-SW of com is ON, turn communication system power supply ONQ97 Voltage control Normally 15V power supply and over voltage controlQ102,111 Voltage control When Comm-SW of com is ON, turn communication system 5V power
16、 supply ONQ103,104 Voltage control LCD backlight and illumination LED controlQ106-108 AVR com system 5V power supply.COMPONENTS DESCRIPTIONXXV-03A4AMP_SCL LX_REQ_MLX_REQ_SLX_DATA_MLX_DATA_SLX_CLKLX_RSTHU_BUAD-IAD-VTEMP1TEMP2TEMP3TEMP4TEMP5TEMP6COMM-SWD-PWERPOWER-ON5VSWV_DOWNPCONLX_CONL_DATA_LL_DATA_
17、AL_CLKL_CEFAN1FAN2AMP_SDAAUDIO_SCLAUDIO_SDAAUDIO_MUTEE2P_SCLE2P_SDALCD-ILLWHITE-LEDMUTE1MUTE2DIP-SW1DIP-SW2DIP-SW3DIP-SW4MODEL1MODEL2DC-DETD-CURAB-CURATT1ATT2ATT3AMP -com784224YGC117Audio controlAMP communication I/F LX BUS I/FDisplay data monitorPower supply controlLCD driver I/FFan controlDestinat
18、ion, AMP IDProtection controlIllumination controlMute controlE2PROM I2Ccommunication MICROPROCESSOR : 784224YGC117 (X09 : IC10) Block Digram Terminal FunctionPin No. Pin Name I/O Function Processing Operation Description13 TEMP4TEMP6 I Temperature detection 464AVSS - GND5 L_CE O CE output to LCD dri
19、ver H : LCD driver CE6 LX_REQ_S O Data transmit request to H/U H : OFF, L : ON7AVREF1 - DA reference voltage8 L_DATA_L I Data input from LCD driver9 L_DATA_A O Data output to LCD driver10 L_CLK O CLK output to LCD driver11 LX_DATA_M I Data input from H/U12 LX_DATA_S O Data output to H/U13 LX_CLK I C
20、LK input from H/U14 LX_BU I LX BUS communication, H/U connect detection H : Not connect (Except master amplifier), L : Connect15 NC O Not used16 SDA_AMP I/O Data input/output AMP communication17 NC O Not usedMICROCOMPUTERS TERMINAL DESCRIPTIONXXV-03A5Pin No. Pin Name I/O Function Processing Operatio
21、n Description18 SCL_AMP I/O CLK input/output AMP communication19 AUDIO_SCL I/O CLK input/output with audio chip20 AUDIO_SDA I/O Data input/output with audio chip21 AUDIO_MUTE O Mute output to audio chip H : Mute OFF, L : Mute ON22 E2P_SCL I/O CLK input/output with E2PROM23 E2P_SDA I/O Data input/out
22、put with E2PROM24 NC O Not used2528 DIP-SW1DIP-SW4 I AMP address setting29 MODEL1 I Model setting 130 MODEL2 I Model setting 231,32 NC O Not used33 VSS1 - GND3437 NC O Not used38 LCD-ILL O LCD backlight switch H : ON, L : OFF39 WHITE-LED O Triangle illumination switch H : ON, L : OFF40 NC O Not used
23、4143 ATT1ATT3 O Output attenuate due to rise in temperature 13 H : Attenuate, L : Not attenuate44,45 NC O Not used46 COMM-SW O Communication IC power switch H : ON, L : OFF4750 NC O Not used51 D-PWER O D class amplifier power supply control H : ON, L : OFF (2ch/4ch L fixed)52 DC-DET I Speaker output
24、 DC voltage detection H : Normal, L : Abnormal53 NC O Not used54 POWER-ON O Amplifier power supply control H : ON (D/AB class), L : OFF55 5VSW O 5VSW H : OFF, L : ON56 MUTE1 O Amplifier section input stage mute control H : OFF, L : ON57 MUTE2 O Driver stage pop-noise mute control H : OFF, L : ON58 F
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- KenwoodXXV03AServiceManual 电路 原理图