Kenwood-TS-590-S-Service-Manual电路原理图.pdf

上传人：cc518

文档编号：80633

上传时间：2020-10-06

格式：PDF

页数：162

大小：6.19MB

《Kenwood-TS-590-S-Service-Manual电路原理图.pdf》由会员分享，可在线阅读，更多相关《Kenwood-TS-590-S-Service-Manual电路原理图.pdf（162页珍藏版）》请在收音机爱好者资料库上搜索。

1、SERVICE MANUALThis product uses Lead Free solder.This product complies with the RoHS directive for the European market. 2010-9 PRINTED IN JA PANB51-8941-00 (N) 283HF / 50MHz ALL MODE TRANSCEIVERTS-590SKey top (8key)(K29-9466-02)Panel(A62-1176-02)Phone jack (9P)(E11-0705-15)RF coaxial receptacle (Rou

2、nd)(E06-0858-25)Key top (25key)(K29-9467-02)RF coaxial receptacle (M)(E04-0167-15)x23.5D phone jack (3P)(E11-0414-15)Rectangular receptacle(E58-0537-05)Sub socket (D)(E58-0529-05)3.5D phone jack (3P)(E11-0455-05)Pin jack(E13-0166-25)x2Foot (Back)(J02-0475-05)x2Phone jack (9P)(E11-0705-15)DIN socket(

3、E56-0408-15)DIN socket(E06-0752-15)Lead wire with connector (EXT.AT)(E37-0891-25)Lead wire with terminal(E37-1480-05)Foot (Front)(J02-0442-04)x2Foot (Front)(J02-0440-04)Knob (Main knob)(K21-1107-13)Key top (20key)(K29-9468-02)Key top (5key)(K29-9469-02)Front glass(B10-2799-02)Knob (RIT)(K29-9471-03)

4、Knob (MULTI)(K29-9456-23)Knob (Inside/NOTCH,AF)(K29-9390-03)x2Knob (Outside/SQL,RF)(K29-9391-13)x2Knob (Inside/HI)(K29-9477-03)Knob (Outside/LO)(K29-9478-03)TS-590S2Document CopyrightsCopyright 2010 by Kenwood Corporation. All rights re-served.No part of this manual may be reproduced, translated, di

5、stributed, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or other-wise, for any purpose without the prior written permission of Kenwood.DisclaimerWhile every precaution has been taken in the preparation of this manual, Kenwood assumes no responsibility

6、for er-rors or omissions. Neither is any liability assumed for dam-ages resulting from the use of the information contained herein. Kenwood reserves the right to make changes to any products herein at any time for improvement purposes.CONTENTSDISASSEMBLY FOR REPAIR . 3CIRCUIT DESCRIPTION . 5COMPONEN

7、TS DESCRIPTION . 20SEMICONDUCTOR DATA . 27PARTS LIST . 34EXPLODED VIEW . 63PACKING . 66ADJUSTMENT . 67TERMINAL FUNCTION . 81PC BOARDFINAL UNIT (X45-391X-XX) . 88CONTROL UNIT (X53-446X-XX) (A/3) . 92CONTROL UNIT (X53-446X-XX) (B,C/3) . 96DISPLAY UNIT (X54-3700-00) . 100TX-RX UNIT (X57-785X-XX) . 104I

8、NTERCONNECTION DIAGRAM . 108SCHEMATIC DIAGRAM . 110BLOCK DIAGRAM . 136LEVEL DIAGRAM . 138OPTIONAL ACCESSORIESPS-60 (DC Power Supply) . 140ARCP-590 (Radio Control Program) . 140ARHP-590 (Radio Host Program) . 140ARUA-10 (USB Audio Controller) . 140SPECIFICATIONS . 141TS-590S3Removing the torque chang

9、eover lever (G02-1858-03)1. Insert the tip of a fl at-head screwdriver (or other imple-ment) under the tab of the torque changeover lever, then lift the tab using the tip of the fl at-head screwdriver. (q)Caution: Be careful not to damage the panel when lifting it.2. Turn the lever section of the to

10、rque changeover lever to the right, as in the position described in step 1. (w):3. Lift the torque changeover lever and remove it from the panel. (e).Mounting the torque changeover lever (G02-1858-03)1. Insert the torque changeover lever by aligning the three tabs of the panel. (q):2. Slightly turn

11、the lever section of the torque changeover lever to the left (e) while pressing the surface near the tab at the lower right of the torque changeover lever (w).Caution: Confirm that the torque changeover lever is caught by the lower right tab of the panel.3. Turn the lever section of the torque chang

12、eover lever to the left (t) while pressing the surface near the tab at the upper right of the torque changeover lever (r), then mount it onto the panel.=;Procedures when Replacing the Diode (1SR139-400) for hand mounting1. When replacing the diode (D304: 1SR139-400) used by the Control unit (A/3) (P

13、CB number: J79-0279-09), cut the leg of a new diode.2mm(0.08 inches)5mm(0.2 inches)Cathode band (Green)DISASSEMBLY FOR REPAIRTS-590S42. Bend the leg of the diode as shown in the fi gure.3. Solder the diode between Q61 (Collector) and the solder pad (Base) of the Control unit (A/3), as shown in the f

14、i g-ure.Note:1) Confi rm the direction of the cathode band when install-ing the diode.2) Install the diode so that it is positioned on the dotted line.3) Install the diode so that its height from the surface of the PCB is 4mm (0.16 inches) or less (Height of rubber sheet (G11-4536-04): 4mm (0.16 inc

15、hes).Install the diode so that it is positioned on the dotted line.Cathode bandControl unit (A/3)Transistor (Q61)Diode (D304)Rubber sheet(G11-4536-04)Diode4mm(0.16 inches)below4mm(0.16 inches)Precautions for ReassemblyPerform the following steps when assembling the bottom side of the transceiver.1.

16、Separate the two coaxial cables (E37-1495-05, E37-1496-05) as shown in the fi gure.2. Push the two fl at cables (E37-1491-05, E37-1492-05) into the gap of the chassis so they do not come into contact with the cabinet.Separate the two coaxial cablesCoaxial cable (E37-1495-05)Coaxial cable (E37-1496-0

17、5)Flat cable (E37-1491-05)Flat cable (E37-1492-05)Push the flat cables into the gap of the chassisCaution for Replacing the LED (B30-2322-05, B30-2323-05)When replacing the “B30-2322-05” or “B30-2323-05” LED used by the Display unit (A/6), order and replace the LED for service into which the rank is

18、 divided according to brightness, according to the following procedures, so that the brightness of the LED backlight remains uniform after replacing the LED.1. Confi rm whether the “A” or “Z” stamp is pushed on the foil side of Display unit (A/6).Confirm whether stamp “A” is pushed.Confirm whether s

19、tamp “Z” is pushed.Display unit (A/6)Foil side2. Order and replace the LED for service as shown in the following table according to whether stamp “A” or “Z” exists or not.Service LED part number for B30-2322-05 (Amber)Service LED part number for B30-2323-05 (Green)Stamp “A” existsStamp “A” does not

20、existStamp “Z”existsStamp “Z” does not existW05-1636-00(High brightness)W05-1637-00(Low and medium brightness)W05-1638-00(High brightness)W05-1639-00(Low and medium brightness)DISASSEMBLY FOR REPAIRTS-590S5Frequency Confi gurationFigure 1 shows the frequency confi guration of this trans-ceiver.While

21、 transmitting, FM mode operates in a double con-version and other modes (AM, SSB, CW, FSK) operate in a triple conversion.While receiving, the fi rst IF operates in 73.095MHz triple conversion. In modes other than FM, the third IF is 24kHz, and the IF signal is converted by an A/D converter and inpu

22、t CIRCUIT DESCRIPTIONinto DSP. The FM mode is detected in the FM IC, and the audio signal is converted by an A/D converter and input into the DSP. Under the following conditions, the fi rst IF oper-ates its reception in 11.374MHz double conversion.1) Modes other than AM or FM2) Amateur band within t

23、he 1.8/3.5/7/14/21MHz bands3) DSP fi lters bandwidth is 2.7kHz or lowerFig. 1 Frequency confi gurationPLLAD4111DDSAD9951DDSAD983511.374MHz1st IF73.095MHz1st IFADCDACDACADCDSP10.695MHz2nd IF3rd IFIFAIFBVCOFM MODRX MIXRX MIXTX MIXx2exceptFMRX MIXTXMIX455kHzFM ICNJM2591FMTX/RXMIXx2x2X50215.6MHzAF24kHz2

24、4kHzAF OUTMIC INANTRX-2RX-1Reference Signal GeneratorThe reference frequency (fstd), which is used to control the individual LO frequencies, oscillates at 15.6MHz in a crystal oscillation circuit (X502, Q501). This 15.6MHz signal passes through a buffer (Q502) and is doubled in a multiplier (Q503) t

25、o generate a 31.2MHz signal. The 31.2MHz signal is used as a reference signal for LO3 (the third local oscillator) DDS (IC601). The 31.2MHz signal is doubled in multipliers (Q504, Q505) to generate a 62.4MHz signal. The 62.4MHz signal is used as a reference signal for LO1 (the fi rst local oscillato

26、r) PLL (IC801).The SO-3 (TCXO unit: 15.6MHz) is confi gured as an op-tion in this transceiver, so that you can replace the crystal oscillation circuit (X502, Q501) with the SO-3. When using the SO-3, remove the CN903 and CN904 short jumper wires in order to stop the operation of the crystal oscillat

27、ion circuit (X502, Q501).LO1/ LO2/ LO3 LO1 (the fi rst local oscillator)The VCO (Q806) oscillates at 196.8MHz. Only the double frequency component, 393.6MHz, of this VCOs oscilla-tion output is extracted and input into PLL (IC801) pin 6. This input signal is divided into 1/N within the PLL. Also, th

28、e 62.4MHz signal (15.6MHz reference frequency x 4) is input into PLL pin 8 and divided into 1/R within the PLL. By a phase comparator in the PLL, the frequency divided into 1/N and the frequency divided into 1/R are compared, and then the frequency is locked. The comparison frequency (f) at this tim

29、e is 120kHz when transmitting FM, and 2.4MHz otherwise.393.6MHz signal locked by PLL (IC801) would be used as reference by DDS (IC803). The output signal from DDS (IC803) is 12.495MHz to 32.195MHz when RX-1 path is selected, amplified at the broad band amplifier (IC804), TS-590S6and then goes throug

30、h BPF and is output as LO1. When RX-2 path is selected or when transmitting, 36.5625MHz to 66.5475MHz is output, amplifi ed by the broad band ampli-fi er (IC804), and then doubled in the multiplier (D652), goes through BPF, and is output as 73.120MHz to 133.095MHz LO1. LO2 (the second local oscillat

31、or)The reference oscillating circuits output signal 15.6MHz signal passes through a buffer (Q502) and is doubled in a multiplier (Q503) to generate a 31.2MHz signal. The 31.2MHz signal is also used as the DDS (IC601)s reference Fig. 2 Reference signal generator, LO1/ LO2/ LO3frequency, and therefore

32、 its resistance is divided. Then, the 31.2MHz signal is doubled in multipliers (Q504, Q505) to generate a 62.4MHz signal.The 62.4MHz signals high harmonic is cut in the BPF and the signal is amplifi ed in the amplifi er (Q506) to gener-ate LO2. If IFB is selected, the diode switch (D501) cuts the LO

33、2 output. LO3 (the third local oscillator)The LO3 used in the modulator and the detector is gen-erated in the DDS (IC601). The DDS output signal passes through the buffer (Q602) and LPF to generate LO3.Q808Q663AMPBufferIC803DDSIC804AMPIC801PLLQ806VCODoublerIC601DDSLPFLPFLPFLPFLPFLPFLPFLPFD651D652L65

34、1BPFBPFHPFD659D670D671 D669D655 D660D654D663D661BPFBPFBPFD653D680 D681D667LO1LO2LO3D657D679D662D668X502,Q50115.6MHzOptionSO-3Q502BufferQ506BufferDoublerQ503DoublerQ504,Q505BufferQ601BufferQ602D501BufferQ801Q804FM MODBufferCIRCUIT DESCRIPTIONTS-590S7Table 1-1 LO1 frequency shift data IF=73MFrequency:

35、 0.0360MHzHF TX/RXLO1DDS AD9951 (DEN1)USB LSB CW CW-R CWNRX TX RX TX RX TX RX TX RX TXFilter offset 1 +1.5k +1.5k 1.5k 1.5k 000000RIT ( RIT) - ( RIT) - ( RIT) - ( RIT) - ( RIT) -XIT - ( XIT) - ( XIT) - ( XIT) - ( XIT) - ( XIT)CAR correction IF10M_2.7k +(CAR1) +(CAR1) (CAR1) (CAR1) +(CAR1) +(CAR1) +(

36、CAR1) +(CAR1) - -HF TX/RXLO1DDS AD9951 (DEN1)CWN-R FSK FSK-R AM FMRX TX RX TX RX TX RX TX RX TXFilter offset 1 0 0 (SHIFT/2) (SHIFT/2) (SHIFT/2) (SHIFT/2) 0000RIT ( RIT) - ( RIT) - ( RIT) - ( RIT) - ( RIT) -XIT - ( XIT) - ( XIT) - ( XIT) - ( XIT) - ( XIT)CAR correction IF10M_2.7k - IF=11MFrequency:

37、0.0321.5MHz (Amateur bands within 1.8/3.5/7/14/21MHz band only)HF TX/RXLO1DDS AD9951 (DEN1)USB LSB CW CW-R CWN CWN-R FSK FSK-RRX RX RX RX RX RX RX RXFilter offset 1 +1.5k 1.5k 0 0 0 0 (SHIFT/2) (SHIFT/2)RIT ( RIT) ( RIT) ( RIT) ( RIT) ( RIT) ( RIT) ( RIT) ( RIT)CARcorrectionIF11M_2.7k +(CAR2) (CAR2)

38、 +(CAR2) +(CAR2) - - - -IF11M_500 +(CAR3) (CAR3) +(CAR3) +(CAR3) - - - -( RIT): RIT frequency variable amount (9.99+9.99kHz)( XIT): XIT frequency variable amount (9.99+9.99kHz)(SHIFT): FSK shift width frequency (170Hz, 200Hz, 425Hz, 850Hz, Initial value:170Hz)CAR correction: SSB IF-Filter adjustment

39、 volume. 0 when using Narrow option fi lter.(CAR1): IF 10.695MHz, SSB Normal fi lter compensation value(CAR2): IF 11.374MHz, Normal fi lter compensation value(CAR3): IF 11.374MHz, Narrow fi lter compensation valueCIRCUIT DESCRIPTIONTS-590S8Receiver CircuitIn an amateur frequency band or mode that re

40、quires anti-proximate interference, the receive signal passes through the double conversion RX-1 path, and in other frequency bands and modes, it passes through the triple conversion RX-2 path. (Refer to table 2)Mode SSB CW FSK AM FMRX-1 pathConversion methodDouble -IF fre-quency1st 11.374MHz -2nd 2

41、4kHz -RX-2 pathConversion methodTripleIF fre-quency1st 73.095MHz2nd 10.695MHz3rd 24kHz 455kHzTable 2 Mode, conversion method, and IF frequencyLO3DDS AD9835 (DEN2)USB LSB CW CW-R CWNRXTX RX TX RX TX RX TX RX TXIF73MIF11MRX21.3M, 21.5RX21.3RX, RX21.5Filter offset 1 46.5k +1.5k 46.5k 46.5k 1.5k 1.5k 00

42、0000CW pitch - -FSK tone - -CAR cor-rectionIF10M_2.7k +(CAR1) +(CAR1) (CAR1) (CAR1) +(CAR1) +(CAR1) +(CAR1) +(CAR1) - -IF11M_2.7k +(CAR2) +(CAR2) (CAR2) +(CAR2) +(CAR2) - -IF11M_500 +(CAR3) +(CAR3) (CAR3) +(CAR3) +(CAR3) - -LO3DDS AD9835 (DEN2)CWN-R FSK FSK-R AM FMRX TX RX TX RX TX RX TX RX TXFilter

43、 offset 1 0 0 00000000CW pitch - - -FSK tone - - -CAR cor-rectionIF10M_2.7k - - -IF11M_2.7k - - -IF11M_500 - - -CAR correction: SSB IF-Filter adjustment volume. 0 when using Narrow option fi lter.(CAR1): IF 10.695MHz, SSB Normal fi lter compensation value(CAR2): IF 11.374MHz, Normal fi lter compensa

44、tion value(CAR3): IF 11.374MHz, Narrow fi lter compensation valueTable 1-2 LO3 frequency shift data From the antenna terminal to the preamplifi er (Q236)The receive signal from the antenna terminals (ANT1/ANT2) passes through the antenna changeover relay (K44) in the Final unit (X45-391 A/2), the an

45、tenna tuners IN/ THROUGH changeover relay (K45), the transmission/recep-tion changeover relay (K46), and an image fi lter, and is sent from CN51 to the TX-RX unit (X57-785 A/2)s CN100 (RAT) through a co-axial cable.The signal input into the TX-RX unit passes through the RX ANT changeover relay (K101) and enters the attenua-tor circuit (ATT) which is approximately 12dB. This can be switched to approximately 20dB by removing the CN101 short jumper. Then, the signal passes th