Kenwood-TK-370-G-Service-Manual电路原理图.pdf

《Kenwood-TK-370-G-Service-Manual电路原理图.pdf》由会员分享，可在线阅读，更多相关《Kenwood-TK-370-G-Service-Manual电路原理图.pdf（50页珍藏版）》请在收音机爱好者资料库上搜索。

1、UHF FM TRANSCEIVERTK-360G/370G 1999-9 PRINTED IN JAPANB51-8494-00(S) 1574SERVICE MANUALGENERAL . 2SYSTEM SET-UP . 2OPERATING FEATURES . 3REALIGNMENT . 8DISASSEMBLY FOR REPAIR . 16CIRCUIT DESCRIPTION . 17SEMICONDUCTOR DATA . 21DESCRIPTION OF COMPONENTS . 23PARTS LIST. 24EXPLODED VIEW . 30CONTENTSKnob

2、 (CHANNEL SELECTOR)(K29-5341-03)Knob (VOL)(K29-5332-03)Cabinet assy(A02-2391-23)Knob (PTT)(K29-5334-13)Antenna(T90-0682-05):MTK-360G TK-370GPACKING . 32ADJUSTMENT . 33PC BOARD VIEWSDISPLAY UNIT (X54-3250-10) . 41TX-RX UNIT (X57-588X-XX) . 43SCHEMATIC DIAGRAM . 49BLOCK DIAGRAM . 57LEVEL DIAGRAM . 59K

3、NB-14/KNB-15A (Ni-Cd BATTERY) . 60OPTIONS . 61SPECIFICATIONS . BACK COVERKnob (ENC)(K29-5331-03)Knob (VOL)(K29-5332-03)Cabinet assy(A02-2385-23)Knob (PTT)(K29-5334-13)Key top (DTMF)(K29-5330-02)M market models are shown.Knob (MON1)(K29-5333-13)Knob (MON1)(K29-5333-13)TK-360G/370G2GENERAL / SYSTEM SE

4、T-UPINTRODUCTIONSCOPE OF THIS MANUALThis manual is intended for use by experienced techniciansfamiliar with similar types of commercial gradecommunications equipment. It contains all required serviceinformation for the equipment and is current as of thepublication date. Changes which may occur after

5、 publicationare covered by either Service Bulletins or Manual Revisions.These are issued as required.ORDERING REPLACEMENT PARTSWhen ordering replacement parts or equipmentinformation, the full part identification number should beincluded. This applies to all parts, components, kits, or chassis.If th

6、e part number is not known, include the chassis or kitnumber of which it is a part, and a sufficient description of therequired component for proper identification.PERSONNEL SAFETYThe following precautions are recommended for personnelsafety:lDO NOT transmit until all RF connectors are verified secu

7、reand any open connectors are properly terminated.lSHUT OFF and DO NOT operate this equipment nearelectrical blasting caps or in an explosive atmosphere.lThis equipment should be serviced by a qualified technician only.SERVICEThis radio is designed for easy servicing. Refer to theschematic diagrams,

8、 printed circuit board views, and alignmentprocedures contained within.NOTEWE CANNOT guarantee oscillator stability when usingchannel element manufactured by other than KENWOOD orits authorized agents.UnitX57-5880-XX X54-3250-XXModel Opt DQT/ID+DTMF(2tone);OptOR Triggers at match with QT Triggers on

9、ly for match with/DQT/ID+DTMF(2tone) ; Opt QT/DQT/ID;SignalingEven if set as OR, there is no Alert/Transpond just withDTMF.Even if set as OR, AF mute cannot be canceled just by amatch with DTMF.In conventional channels not set with QT/DQT, signaling isa match just by receiving the carrier.Auto Reset

10、When Option Signaling matches on a Group channel whereit is set to Yes, Option Signaling is canceled when it matches agroup channel set to Yes.After Option Signaling matches, Option Signaling canautomatically Reset after a specified time.Dead Beat DisableWhen the D.B.D (Dead Beat Disable) code match

11、es, apreset operation is performed.When D.B.D matches on all group channels regardless ofwhether Option Signaling = Yes/No, then TX Inhibit or TX RXInhibit is activated by the settings performed afterwards. D.B.Dis canceled when the D.B.D. code + “#“ is received.Transpond is always activated when th

12、e D.B.D code is amatches. Alert is not output. An Option Signaling match is notdisplayed.TK-360G/370G87. Audible user feedback tones (TK-370Gonly)The transceiver outputs various combinations of tones tonotify the user of the transceiver operating state. The maintones are listed belowThe high tone is

13、 1477Hz, the mid tone is 941Hz, and thelow tone is 770Hz. Power on toneThis tone is output when the transceiver is turned on. (Thehigh tone is output for 500ms.) Alert toneThis tone is output when the transceiver is in TX inhibitionfor TOT, battery warning and PLL unlocked. It is output untilthe PTT

14、 button is released. (The 697Hz tone is output.) Busy ToneThis informs the user of a busy channel lock out Group Call ToneThe group call tone informs the user of a group call in DTMF/2 Tone Option Signaling. This tone repeats 7 times. Individual ToneIndividual tone is issued on receiving selective c

15、all by DTMF/2 Tone Option Signaling. Pre Alert toneInforms the user when nearing transmit inhibit (transmitcutoff) time due to TOT.The Pre Alert Tone is issued from the time set for TOT PreAlert until the TOT triggers.1633Hz 1633Hz 1633Hz50ms 50ms 50ms 50ms 50ms2000Hz 2000Hz 2000Hz100ms 100ms 100ms

16、100ms 100ms770Hz 770Hz30ms 30ms 30msREALIGNMENT1. ModesMode FunctionUser mode For normal use.Panel test mode Used by the dealer to check thefundamental characteristics.Panel tuning mode Used by the dealer to tune the radio.PC mode Used for communication between theradio and PC (IBM compatible).Data

17、programming Used to read and write frequency datamode and other features to and from the radio.PC test mode Used to check the radio using the PC.This feature is included in the FPU.See panel tuning.Firmware program- Used when changing the mainming mode program of the flash memory.Clone mode Used to

18、transfer programming datafrom one radio to another.Self programming Frequency, signalling and features.modeUser modePanel test mode(TK-370G only)PC modeFirmwareprogramming modeClone modeSelf programmingmode (TK-370G only)Panel tuning modePC test modeData programmingmodePC tuning modeChecksumOPERATIN

19、G FEATURES / REALIGNMENT2. How to Enter Each ModeMode OperationUser mode Power ONPanel test mode 2+Power ON (Two seconds)(TK-370G only)PC mode Received commands from PCPanel tuning mode Panel test mode+Firmware programming mode LAMP+MONI+Power ON(Two seconds)Clone mode LAMP+3+Power ON(Two seconds)Se

20、lf programming mode LAMP+Power ON(Two seconds) (TK-370G only)3. For the panel Test Mode (TK-370G only)For the setting method, refer to ADJUSTMENT.3-1. For the panel Tuning ModeFor the setting method, refer to ADJUSTMENT.TK-360G/370G9Fig. 16. Firmware Programming Mode6-1. PrefaceFlash memory is mount

21、ed on the TK-360G/370G. Thisallows the TK-360G/370G to be upgraded when new featuresare released in the future. (For details on how to obtain thefirmware, contact Customer Service.)6-2. Connection procedureConnect the TK-360G/370G to the personal computer (IBMPC or compatible) with the interface cab

22、le (KPG-22).(Connection is the same as in the PC Mode.)6-3. Programming1. Start up the programming software (KPG-56D), select“firmware program“ in the “Program“ item, and press theReturn key on your personal computer. This starts up thefirmware programmer.2. The top screen is displayed. Press any ke

23、y to advance tothe next screen.3. Set the communications speed (normally, 57600 bps) andcommunications port in the Setup item.4. Set the firmware to be updated by File select (=F1).5. Hold down the LAMP and MON switches on the TK-360G/370G, and press the power switch.When the LAMP and MON switches a

24、re held down fortwo seconds, “PROG 576“ appears on the display andthe LED lights orange. When “PROG 576“ is displayed,release the switches. (TK-370G only)6. Check the connection between the TK-360G/370G and thepersonal computer, and make sure that the TK-360G/370Gis in Program mode.7. Press F10 on t

25、he personal computer. A window opens onthe display to indicate the writing progress. When the TK-360G/370G begins to receive data, the LED lights green.8. When data is received successfully, a checksum appearson the display.(Since the TK-360G does not have a display, check thechecksum with the FPU (

26、KPG-56D).)REALIGNMENT4. ChecksumExecuting this function, “TUNING“ appears on the displayof TK-370G while calculating the checksum .When the calculation is completed, the display returns tonormal and PC displays the checksum of the radio.5. PC Mode5-1. PrefaceThe TK-360G/370G transceiver is programme

27、d using apersonal computer, a programming interface (KPG-22) andprogramming software (KPG-56D).The programming software can be used with an IBM PC orcompatible. Figure 1 shows the setup of an IBM PC forprogramming.5-2. Connection procedure1. Connect the TK-360G/370G to the personal computer withthe

28、interface cable.2. When the POWER is switched on, user mode can beentered immediately. When the PC sends a command, theradio enters PC mode.When data is transmitted from transceiver, the red LEDblink.When data is received by the transceiver, the green LEDblinks.Notes: The data stored in the personal

29、 computer must match modeltype when it is written into the flash memory. Change the TK-360G/370G to PC mode, then attach theinterface cable.5-3. KPG-22 description(PC programming interface cable: Option)The KPG-22 is required to interface the TK-360G/370G tothe computer. It has a circuit in its D-su

30、bconnector (25-pin)case that converts the RS-232C logic level to the TTL level.The KPG-22 connects the SP/MIC connector of the TK-360G/370G to the computers RS-232C serial port.5-4. Programming software descriptionThe KPG-56D programming disk is supplied in 3-1/2” diskformat. The software on this di

31、sk allows a user to program theTK-360G/370G radios via a programming interface cable (KPG-22).5-5. Programming with IBM PCIf data is transferred to the transceiver from an IBM PC withthe KPG-56D, the destination data (basic radio information)for each set can be modified. Normally, it is not necessar

32、y tomodify the destination data because their values aredetermined automatically when the frequency range (frequencytype) is set.The values should be modified only if necessary. Data canbe programmed into the flash memory in RS-232C format viathe universal connector.KPG-56D installation manual part

33、No. : B62-1153-XXTK-360G/370G10REALIGNMENT9. If you want to continue programming other TK-360G/370Gs, repeat steps 5 to 8.Notes:lTo start the Firmware Programmer from KPG-56D, the Fpropath must be set up by the KPG-56D Setup.lThis mode cannot be entered if the Firmware Programmingmode is set to Disa

34、ble in the Programming software (KPG-56D).lWhen programming the firmware, it is recommend to copythe data from the floppy disk to your hard disk before youupdate the radio firmware.Directly copying from the floppy disk to the radio may notwork because the access speed is too slow.6-4. Function1. If

35、you press the MON switch while “PROG XXX“ isdisplayed, the checksum is displayed. If you press theMON switch again (while the checksum is displayed),“PROG XXX“ is redisplayed.2. A transmission speed can be selected by pressing theLAMP switch while “PROG XXX“ is displayed.12900 bps: The LED flashes g

36、reen and red alternately.38400 bps: The LED flashes orange.57600 bps: The LED lights orange.Note:Normally, write in the high-speed mode.7. Clone ModeProgramming data can be transferred from one radio toanother by connecting them via their SP/MIC connectors. Theoperation is as follows (the transmit r

37、adio is the master andthe receive radio is the slave).1. Turn the master TK-370G power ON with the LAMP+3key held down. The TK-370G displays “ CLONE “.2. Power on the slave TK-360G/370G.3. Connect the cloning cable to the SP/MIC connectors onthe master and slave.4. Press the key on the master while

38、the master displays“ CLONE “. The data of the master is sent to the slave.While the slave is receiving the data, “-PC-“ is displayed.When cloning of data is completed, the master displays“END“, and the slave automatically operates in the Usermode. The slave can then be operated by the same programas

39、 the master.5. The other slave can be continuously cloned. When the key on the master is pressed while the master displays“END“, the master displays “ CLONE “. Carry out theoperation in steps 2 to 4.Note: You can clone the programmed data between thetransceiver listed below.Frequency version must be

40、 same.Slave TK-360G TK-360G TK-860G TK-860GKMKMTK-370G TK-370G TK-862G TK-862GMasterKMKMTK-370GKTK-370GM3.52.53.52.5GNDREMOTE/TXDPTT/RXDFig. 2Cloning cableE30-3411-05 (TK-370G TK-860G/862G)MBLPSBGNDPTT/RXDMEMICREMOTE/TXDCMGNDREMOTE/TXDPTT/RXD8118Cloning cable parts No.E30-3410-05 (TK-370G TK-360G/370G)