Jvc-UXG-300-Service-Manual电路原理图.pdf

《Jvc-UXG-300-Service-Manual电路原理图.pdf》由会员分享，可在线阅读，更多相关《Jvc-UXG-300-Service-Manual电路原理图.pdf（59页珍藏版）》请在收音机爱好者资料库上搜索。

1、SERVICE MANUALCOPYRIGHT 2008 Victor Company of Japan, LimitedNo.MB6652008/9MICRO COMPONENT SYSTEMMB66520089SERVICE MANUALUX-G300B, UX-G300E, UX-G300EN, UX-G300EV, UX-G303E, UX-G303EN, UX-G303EV, UX-G305E, UX-G305EN, UX-G305EV, UX-G300A, UX-G300US, UX-G300UF, UX-G300UT, UX-G300UW, UX-G300UG, UX-G300U

2、N, UX-G305UTCOPYRIGHT 2008 Victor Company of Japan, LimitedLead free solder used in the board (material : Sn-Ag-Cu, melting point : 219 Centigrade)Lead free solder used in the board (material : Sn-Cu, melting point : 230 Centigrade)TABLE OF CONTENTS1 PRECAUTION. . . . . . . . . . . . . . . . . . . .

3、 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-42 SPECIFIC SERVICE INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-73 DISASSEMBLY . . . . . . . . . . . . . . . . .

4、 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-74 ADJUSTMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-205 TROUBLESHOOTING . . . . . .

5、 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-21UX-G300EVUX-G303EVUX-G305EVSP-UXG300SP-UXG300CA-UXG3001-2 (No.MB665)SPECIFICATIONUX-G300 B/E/EN/EVUX-G303 E/EN/EVUX-G305 E/EN/EVSpecifications and appearance are subject to chan

6、ge without prior notice.Amplifier sectionOUTPUT POWER 60 W (30 W + 30 W) at 4 (10% THD)Speakers/Impedance 4 - 16 Audio input AUDIO IN 500 mV/47 k (at “IN LVL1”)250 mV/47 k (at “IN LVL2”)125 mV/47 k (at “IN LVL3”)Digital input USB MEMORYTuner sectionFM tuning range 87.50 MHz - 108.00 MHzAM (MW) tunin

7、g range 522 kHz - 1 629 kHzCD player sectionDynamic range 88 dBSignal-to-noise ratio 85 dBWow and flutter ImmeasurableUSB storageUSB specification Compatible with USB 2.0 Full SpeedCompatible device Mass storage classCompatible file system “FAT16,FAT32“Bus power supply Max. 500 mASpeakersSpeaker uni

8、ts 10 cm cone x 1Impedance 4 Dimensions (approx.) 160 mm x 250 mm x 150 mm (W/H/D)Mass (approx.) 1.6 kg eachGeneralPower requirements “AC 230,50 Hz“Power supply to USB mass storage class device DC 5 V =500 mAPower consumption 20 W (power on)6.5 W (standby mode)1 W or less (Save Mode)Dimensions (W x

9、H x D) 165 mm x 251 mm x 269 mmMass 2.6 kg(No.MB665)1-3UX-G300 US/UN/UB/UG/A/UW/UF/UTUX-G305UTSpecifications and appearance are subject to change without prior notice.Amplifier sectionOUTPUT POWER 60 W (30 W + 30 W) at 4 (10% THD)Speakers/Impedance 4 - 16 Audio input AUDIO IN 500 mV/47 k (at “IN LVL

10、1”)250 mV/47 k (at “IN LVL2”)125 mV/47 k (at “IN LVL3”)Digital input USB MEMORYTuner sectionFM tuning range 87.50 MHz - 108.00 MHzAM (MW) tuning range 530 kHz - 1 710 kHz (in 10 kHz spacing)531 kHz - 1 710 kHz (in 9 kHz spacing)CD player sectionDynamic range 88 dBSignal-to-noise ratio 85 dBWow and f

11、lutter ImmeasurableUSB storageUSB specification Compatible with USB 2.0 Full SpeedCompatible device Mass storage classCompatible file system FAT16, FAT32Bus power supply Max. 500 mASpeakersSpeaker units 10 cm cone x 1Impedance 4 Dimensions (approx.) 160 mm x 250 mm x 150 mm (W/H/D)Mass (approx.) 1.6

12、 kg eachGeneralPower requirements AC 110 V - AC 240 V , 50/60 HzAC 240 V , 50 Hz (only Australia)AC 220 V , 50 Hz (only Hong Kong)Power supply to USB mass storage class device DC 5 V =500 mAPower consumption 20 W (power on)6.5 W (standby mode)1 W or less (Save Mode)Dimensions (W x H x D) 165 mm x 25

13、1 mm x 269 mmMass 2.6 kg1-4 (No.MB665)SECTION 1PRECAUTION1.1 Safety Precautions(1) This design of this product contains special hardware andmany circuits and components specially for safety purpos-es. For continued protection, no changes should be madeto the original design unless authorized in writ

14、ing by themanufacturer. Replacement parts must be identical tothose used in the original circuits. Services should be per-formed by qualified personnel only.(2) Alterations of the design or circuitry of the product shouldnot be made. Any design alterations of the product shouldnot be made. Any desig

15、n alterations or additions will voidthe manufacturers warranty and will further relieve themanufacture of responsibility for personal injury or propertydamage resulting therefrom.(3) Many electrical and mechanical parts in the products havespecial safety-related characteristics. These characteris-ti

16、cs are often not evident from visual inspection nor can theprotection afforded by them necessarily be obtained by us-ing replacement components rated for higher voltage, watt-age, etc. Replacement parts which have these specialsafety characteristics are identified in the Parts List of Ser-vice Manua

17、l. Electrical components having such featuresare identified by shading on the schematics and by ( ) onthe Parts List in the Service Manual. The use of a substitutereplacement which does not have the same safety charac-teristics as the recommended replacement parts shown inthe Parts List of Service M

18、anual may create shock, fire, orother hazards.(4) The leads in the products are routed and dressed with ties,clamps, tubings, barriers and the like to be separated fromlive parts, high temperature parts, moving parts and/orsharp edges for the prevention of electric shock and firehazard. When service

19、 is required, the original lead routingand dress should be observed, and it should be confirmedthat they have been returned to normal, after reassem-bling.(5) Leakage shock hazard testingAfter reassembling the product, always perform an isola-tion check on the exposed metal parts of the product (an-

20、tenna terminals, knobs, metal cabinet, screw heads,headphone jack, control shafts, etc.) to be sure the productis safe to operate without danger of electrical shock.Do notuse a line isolation transformer during this check. Plug the AC line cord directly into the AC outlet. Using a“Leakage Current Te

21、ster“, measure the leakage currentfrom each exposed metal parts of the cabinet, particular-ly any exposed metal part having a return path to thechassis, to a known good earth ground. Any leakage cur-rent must not exceed 0.5mA AC (r.m.s.). Alternate check methodPlug the AC line cord directly into the

22、 AC outlet. Use anAC voltmeter having, 1,000 per volt or more sensitivityin the following manner. Connect a 1,500 10W resistorparalleled by a 0.15F AC-type capacitor between an ex-posed metal part and a known good earth ground.Measure the AC voltage across the resistor with the ACvoltmeter. Move the

23、 resistor connection to each exposed metalpart, particularly any exposed metal part having a returnpath to the chassis, and measure the AC voltage acrossthe resistor. Now, reverse the plug in the AC outlet andrepeat each measurement. Voltage measured any mustnot exceed 0.75 V AC (r.m.s.). This corre

24、sponds to 0.5mA AC (r.m.s.). 1.2 Warning(1) This equipment has been designed and manufactured tomeet international safety standards.(2) It is the legal responsibility of the repairer to ensure thatthese safety standards are maintained.(3) Repairs must be made in accordance with the relevantsafety st

25、andards.(4) It is essential that safety critical components are replacedby approved parts.(5) If mains voltage selector is provided, check setting for localvoltage.1.3 CautionBurrs formed during molding may be left over on some partsof the chassis. Therefore, pay attention to such burrs in the case

26、of pre-forming repair of this system.1.4 Critical parts for safetyIn regard with component parts appearing on the silk-screenprinted side (parts side) of the PWB diagrams, the parts that areprinted over with black such as the resistor ( ), diode ( )and ICP ( ) or identified by the “ “ mark nearby ar

27、e criticalfor safety. When replacing them, be sure to use the parts of thesame type and rating as specified by the manufacturer. (This regulation dose not Except the J and C version)Good earth groundPlace this probe on each exposedmetal part.AC VOLTMETER(Having 1000 ohms/volts,or more sensitivity)15

28、00 10W0.15 F AC TYPE(No.MB665)1-51.5 Preventing static electricityElectrostatic discharge (ESD), which occurs when static electricity stored in the body, fabric, etc. is discharged, can destroy the laserdiode in the traverse unit (optical pickup). Take care to prevent this when performing repairs.1.

29、5.1 Grounding to prevent damage by static electricityStatic electricity in the work area can destroy the optical pickup (laser diode) in devices such as laser products. Be careful to use proper grounding in the area where repairs are being performed. (1) Ground the workbenchGround the workbench by l

30、aying conductive material (such as a conductive sheet) or an iron plate over it before placing thetraverse unit (optical pickup) on it.(2) Ground yourselfUse an anti-static wrist strap to release any static electricity built up in your body. (3) Handling the optical pickup In order to maintain quali

31、ty during transport and before installation, both sides of the laser diode on the replacement opticalpickup are shorted. After replacement, return the shorted parts to their original condition. (Refer to the text.) Do not use a tester to check the condition of the laser diode in the optical pickup.

32、The testers internal power source can easilydestroy the laser diode. 1.6 Handling the traverse unit (optical pickup)(1) Do not subject the traverse unit (optical pickup) to strong shocks, as it is a sensitive, complex unit. (2) Cut off the shorted part of the flexible cable using nippers, etc. after

33、 replacing the optical pickup. For specific details, refer to thereplacement procedure in the text. Remove the anti-static pin when replacing the traverse unit. Be careful not to take too long atime when attaching it to the connector. (3) Handle the flexible cable carefully as it may break when subj

34、ected to strong force. (4) I t is not possible to adjust the semi-fixed resistor that adjusts the laser power. Do not turn it.1.7 Attention when traverse unit is decomposed*Please refer to “Disassembly method“ in the text for the pickup unit. Apply solder to the short land sections before the card w

35、ire is disconnected from the connecto on the servo board. (If the card wireis disconnected without applying solder, the pickup may be destroyed by static electricity.) In the assembly, be sure to remove solder from the short land sections after connecting the card wire.1MConductive material(conducti

36、ve sheet) or iron palate(caption)Anti-static wrist strapSolder short land section1-6 (No.MB665)1.8 Important for laser products1.CLASS 1 LASER PRODUCT 2.CAUTION : (For U.S.A.) Visible and/or invisible class II laser radiationwhen open. Do not stare into beam.(Others) Visible and/or invisible class 1

37、M laser radiationwhen open. Do not view directly with optical instruments. 3.CAUTION : Visible and/or invisible laser radiation whenopen and inter lock failed or defeated. Avoid directexposure to beam.4.CAUTION : This laser product uses visible and/or invisible laser radiation and is equipped with s

38、afety switches which prevent emission of radiation when the drawer is open and the safety interlocks have failed or are defeated. It is dangerous to defeat the safety switches.5.CAUTION : If safety switches malfunction, the laser is ableto function. 6.CAUTION : Use of controls, adjustments or perfor

39、mance of procedures other than those specified here in may result in hazardous radiation exposure. REPRODUCTION AND POSITION OF LABELS and PRINT!Please use enough caution not to see the beam directly or touch it in case of an adjustment or operationcheck. WARNING LABEL and PRINT(No.MB665)1-7SECTION

40、2SPECIFIC SERVICE INSTRUCTIONSNew CD mechanism was added.In a model using new CD mechanism for, it stick a blue label for identification on the back side.When it repair the CD mechanism of an article sticking this label on, please use a parts list of FMU-VK1-2M.SECTION 3DISASSEMBLY3.1 Main body (Use

41、d figure are UX-G300E)3.1.1 Removing the Metal Cover (See Fig.1, 2)(1) Remove the seven screws A attaching the Metal cover.(See Fig.1)(2) Remove the two screws B attaching the both side of theMetal cover. (See Fig.2)Fig.1Fig.2A label for identificationA AB1-8 (No.MB665)3.1.2 Removing the Tuner pack

42、(See Fig.3, 4)(1) Disconnect the card wire from Tuner pack connected toconnector CN306 of the Micom board. (See Fig.3)(2) Remove the two screws C attaching the Tuner pack. (SeeFig.4)Fig.3Fig.43.1.3 Removing the Rear panel (See Fig.5)(1) Remove the five screws D attaching the Rear panel.Fig.53.1.4 Re

43、moving the Amp board (See Fig.6)(1) Disconnect the connector wire from Power board connect-ed to connector CN640 of the Amp board.(2) Disconnect the card wire from Amp board connected toconnector CN520 of the Micom board.(3) Remove the one screw E attaching the Amp board.Fig.6CN306CDECN520CN640(No.M

44、B665)1-93.1.5 Removing the CD mechanism (See Fig.7 to 9)(1) Disconnect the card wire from CD mechanism connectedto connector CN360 and CN362 of the Connection board.(See Fig.7)(2) Disconnect the card wire from CD mechanism connectedto connector CN205 of the Power board. (See Fig.7)(3) Remove the two

45、 screws F attaching the CD mechanism.(See Fig.8)(4) Disconnect the connector wire from USB jack board con-nected to connector CN802 of the CD servo control board.(See Fig.9)Fig.7Fig.8Fig.9CN360CN362CN205FCN8021-10 (No.MB665)3.1.6 Removing the Mecha chassis (See Fig.10, 11)(1) Remove the two screws G attaching the both side of theFront panel. (See Fig.10)(2) Disconnect the card wire from Connection board connect-ed to connector CN311 of the Micom board. (See Fig.11)Fig.10Fig.11GCN311