Jvc-XVBP-1-UJ-Service-Manual电路原理图.pdf

《Jvc-XVBP-1-UJ-Service-Manual电路原理图.pdf》由会员分享，可在线阅读，更多相关《Jvc-XVBP-1-UJ-Service-Manual电路原理图.pdf（107页珍藏版）》请在收音机爱好者资料库上搜索。

1、MODELS:XV-BP1C/XV-BP1UJSERVICE MANUALP/NO : AFN73065055 APRIL, 2009MODELS : XV-BP1C/XV-BP1UJBLU-RAY DISC PLAYER1-1CONTENTSSECTION 1 .SUMMARYSECTION 2 .CABINET & MAIN CHASSISSECTION 3 .ELECTRICALSECTION 4 .HL-04P LOADER PARTSECTION 5 .REPLACEMENT PARTS LIST1-2SECTION 1SUMMARYCONTENTSPRODUCT SAFETY SE

2、RVICING GUIDELINES FORBLU-RAY DISC PLAYER PRODUCTS. 1-3SERVICING PRECAUTIONS . 1-4 General ServicinG PrecautionS inSulation checkinG Prodedure electroStatically SenSitive (eS) deviceSSOFTWARE UPGRADE . 1-5SPECIFICATIONS . 1-61-3PRODUCT SAFETY SERVICING GUIDELINESFOR BLU-RAY DISC PLAYER PRODUCTSIMPOR

3、TANT SAFETY NOTICEthis manual was prepared for use only by properly trained audio-video service technicians.When servicing this product, under no circumstances should the original design be modified or altered without permission from Jvc. all components should be replaced only with types identical t

4、o those in the original circuit and their physical location, wiring and lead dress must conform to original layout upon completion of repairs.Special components are also used to prevent x-radiation, shock and fire hazard.these components are indicated by the letter “x” included in their component de

5、s-ignators and are required to maintain safe performance. no deviations are allowed without prior approval by Jvc.circuit diagrams may occasionally differ from the actual circuit used. this way, implementation of the latest safety and performance improvement changes into the set is not delayed until

6、 the new service literature is printed.CAUTION : do not attempt to modify this product in any way. never perform cus-tomized installations without manufacturers approval. unauthorized modifications will not only void the warranty, but may lead to property damage or user injury.Service work should be

7、 performed only after you are thoroughly familiar with these safety checks and servicing guidelines.GRAPHIC SYMBOLSthe exclamation point within an equilateral triangle is intended to alert the service personnel to important safety information in the service literature.the lightning flash with arrowh

8、ead symbol within an equilateral triangle is intended to alert the service personnel to the presence of noninsulated “dangerous voltage” that may be of sufficient magnitude to constitute a risk of electric shock.the pictorial representation of a fuse and its rating within an equi-lateral triangle is

9、 intended to convey to the service personnel the following fuse replacement caution notice:CAUTION : For continued Protection aGainSt riSk oF Fire, rePlace all FuSeS With the SaMe tyPe and ratinG aS Marked near each FuSe.SERVICE INFORMATIONWhile servicing, use an isolation transformer for protection

10、 from ac line shock. after the original service problem has been corrected, make a check of the following:FIRE AND SHOCK HAZARD1. Be sure that all components are positioned to avoid a possibility of adjacent component shorts. this is especially important on items trans-ported to and from the repair

11、shop.2. verify that all protective devices such as insulators, barriers, covers, shields, strain reliefs, power supply cords, and other hardware have been reinstalled per the original design. Be sure that the safety purpose of the polarized line plug has not been defeated.3. Soldering must be inspec

12、ted to discover possible cold solder joints, solder splashes, or sharp solder points. Be certain to remove all loose foreign par-ticles.4. check for physical evidence of damage or deterioration to parts and compo-nents, for frayed leads or damaged insulation (including the ac cord), and replace if n

13、ecessary.5. no lead or component should touch a high current device or a resistor rated at 1 watt or more. lead tension around protruding metal surfaces must be avoided.6. after reassembly of the set, always perform an ac leakage test on all exposed metallic parts of the cabinet (the channel selecto

14、r knobs, antenna terminals, handle and screws) to be sure that set is safe to operate without danger of electrical shock. do not uSe a line iSolation tranSForMer durinG thiS teSt. use an ac voltmeter having 5000 ohms per volt or more sensitivity in the following manner: connect a 1500 ohm, 10 watt r

15、esistor, paralleled by a .15 mfd 150v ac type capacitor between a known good earth ground water pipe, conduit, etc.) and the exposed metallic parts, one at a time. Measure the ac volt-age across the combination of 1500 ohm resistor and .15 mfd capacitor. reverse the ac plug by using a non-polarized

16、adaptor and repeat ac voltage measure-ments for each exposed metallic part. voltage measured must not exceed 0.75 volts rMS. this corresponds to 0.5 milliamp ac. any value exceeding this limit constitutes a potential shock hazard and must be corrected immediately.TIPS ON PROPER INSTALLATION1. never

17、install any receiver in a closed-in recess, cubbyhole, or closely fitting shelf space over, or close to, a heat duct, or in the path of heated air flow. 2. avoid conditions of high humidity such as: outdoor patio installations where dew is a factor, near steam radiators where steam leakage is a fact

18、or, etc. 3. avoid placement where draperies may obstruct venting. the customer should also avoid the use of decorative scarves or other coverings that might obstruct ventilation.4. Wall- and shelf-mounted installations using a commercial mounting kit must follow the factory-approved mounting instruc

19、tions. a product mounted to a shelf or platform must retain its original feet (or the equivalent thickness in spacers) to provide adequate air flow across the bottom. Bolts or screws used for fasteners must not touch any parts or wiring. Perform leakage tests on customized instal-lations.5. caution

20、customers against mounting a product on a sloping shelf or in a tilted position, unless the receiver is properly secured.6. a product on a roll-about cart should be stable in its mounting to the cart.caution the customer on the hazards of trying to roll a cart with small casters across thresholds or

21、 deep pile carpets.7. caution customers against using extension cords. explain that a forest of exten-sions, sprouting from a single outlet, can lead to disastrous consequences to home and family.1-4SERVICING PRECAUTIONScaution: Before servicing the Blu-ray diSc Player cov-ered by this service data

22、and its supplements and addends, read and follow the SaFety PrecautionS. note: if unforeseen circumstances create conflict between the follow-ing servicing precautions and any of the safety precautions in this publications, always follow the safety precautions.remember Safety First :General Servicin

23、g Precautions1. always unplug the Blu-ray diSc Player ac power cord from the ac power source before:(1) removing or reinstalling any component, circuit board, module, or any other assembly.(2) disconnecting or reconnecting any internal electrical plug or other electrical connection.(3) connecting a

24、test substitute in parallel with an electro-lytic capacitor.Caution : a wrong part substitution or incorrect polar-ity installation of electrolytic capacitors may result in an explosion hazard.2. do not spray chemicals on or near this Blu-ray diSc Player or any of its assemblies.3. unless specified

25、otherwise in this service data, clean elec-trical contacts by applying an appropriate contact cleaning solution to the contacts with a pipe cleaner, cotton-tipped swab, or comparable soft applicator. unless specified otherwise in this service data, lubrication of contacts is not required.4. do not d

26、efeat any plug/socket B+ voltage interlocks with whitch instruments covered by this service manual might be equipped.5. do not apply ac power to this Blu-ray diSc Player and / or any of its electrical assemblies unless all solidstate device heat sinks are correctly installed.6. always connect the te

27、st instrument ground lead to an appropriate ground before connecting the test instrument positive lead. always remove the test instrument ground lead last.Insulation Checking Proceduredisconnect the attachment plug from the ac outlet and turn the power on. connect an insulation resistance meter (500

28、v)to the blades of the attachment plug. the insulation resistance between each blade of the attachment plug and accessible conductive parts (note 1) should be more than 1Mohm.Note 1 : accessible conductive Parts include Metal panels, input terminals, earphone jacks,etc.Electrostatically Sensitive (E

29、S) DevicesSome semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are called electrostatically Sensitive (eS) devices. examples of typical eS devices are integrated circuits and some field effect transistors and semiconductor chip components.the

30、 following techniques should be used to help reduce the incidence of component damage caused by static electricity.1. immediately before handling any semiconductor compo-nent or semiconductor-equipped assembly, drain off any electrostatic charge on your body by touching a known earth ground. alterna

31、tively, obtain and wear a commercially available discharging wrist strap device, which should be removed for potential shock reasons prior to applying power to the unit under test.2. after removing an electrical assembly equipped with eS devices, place the assembly on a conductive surface such as al

32、uminum foil, to prevent electrostatic charge buildup or exposure of the assembly.3. use only a grounded-tip soldering iron to solder or unsolder eS devices.4. use only an anti-static solder removal device. Some solder removal devices not classified as “anti-static” can generate electrical charges su

33、fficient to damage eS devices.5. do not use freon-propelled chemicals. these can generate an electrical charge sufficient to damage eS devices.6. do not remove a replacement eS device from its protective package until immediately before you are ready to install it. (Most replacement eS devices are p

34、ackaged with leads electrically shorted together by conductive foam, aluminum foil,or comparable conductive material).7. immediately before removing the protective material from the leads of a replacement eS device, touch the protective material to the chassis or circuit assembly into which the devi

35、ce will be installed.caution: Be sure no power is applied to the chassis or cir-cuit, and observe all other safety precautions.8. Minimize bodily motions when handling unpackaged replacement eS devices. (normally harmless motion such as the brushing together of your clothes fabric or the lifting of

36、your foot from a carpeted floor can generate static elec-tricity sufficient to damage an eS device.)1-5 Burn a dvd recordable disc or uSB with a file that is named to “Jvc_Bd_310M.roM”. insert a upgrading disc or uSB. Show help message for disc upgrade as follows.Press play key to upgrade and it wil

37、l show progress informationafter completing upgrade then power is off.SOFTWARE UPGRADE1-6SPECIFICATIONS GeneralPower requirements: ac 120v, 60hzPower consumption: 18Wdimensions (W x h x d): approx. 16.9 x 2.1 x 9.7inches (430 x 54 x 245mm) without footWeight (approx.): 6.2lbs (2.8kg)operating temper

38、ature: 41F to 95F (5c to 35c)operating humidity: 5% to 90% Outputsvideo out: 1.0v (p-p), 75, sync negative, rca jack x 1coMPonent video out: (y) 1.0v (p-p), 75, sync negative, rca jack x 1(Pb)/(Pr) 0.7v (p-p), 75, rca jack x 2hdMi out (video/audio): 19pin (hdMi standard, type a)analoG audio out: 2.0

39、vrms (1khz, 0dB), 600, rca jack (l, r) x 1diGital out (coaXial): 0.5v (p-p), 75, rca jack x 1diGital out (oPtical): 3v (p-p), optical jack x 1 systemlaser: Semiconductor laser, wavelength: 405nm / 650nmSignal system: Standard ntSc color tv systemFrequency response: 20hz to 20khz (48khz, 96khz, 192kh

40、z sampling)Signal-to-noise ratio: More than 100dB (analoG out connectors only)harmonic distortion: less than 0.008%dynamic range: More than 95dBlan port: ethernet jack x 1, 10BaSe-t/100BaSe-tX2-1SECTION 2CABINET & MAIN CHASSISCONTENTSDISASSEMBLY INSTRUCTIONS . 2-2EXPLODED VIEWS . 2-31. caBinet and M

41、ain FraMe Section . 2-32. deck MechaniSM Section (hl-04P) . 2-43. PackinG acceSSory Section . 2-52-2DISASSEMBLY INSTRUCTIONS1. it is the product appearance.2. remove the three screws on the back panel to seperate the top cover.3. Push the top cover backward to seperate the top cover completely.4. re

42、move the nine front panel hooks (four hooks on the top, two hooks on the both side and three hooks on the bottom) to seperate the front panel.5. it is the feature that the top and front panel are seperated.2-3SVC purchase order cautionkey board is array coming timer board.Purchase order board separa

43、tely supply incomprehensible.Supply is possible in location no. a50 state in exploded views.462250468BCABLE4c468A47SMPSBOARDMAINBOARDBca468A46468468468A44465320465260261261261470KEYBOARDaTIMERBOARD283284287275275452452452452CABLE2PN401A50A43A43AEXPLODED VIEWS1. CABINET AND MAIN FRAME SECTIONCABLE3300