Jvc-NXD-5-Service-Manual电路原理图.pdf

《Jvc-NXD-5-Service-Manual电路原理图.pdf》由会员分享，可在线阅读，更多相关《Jvc-NXD-5-Service-Manual电路原理图.pdf（55页珍藏版）》请在收音机爱好者资料库上搜索。

1、SERVICE MANUALCOPYRIGHT 2009 Victor Company of Japan, LimitedNo.MB7112009/10COMPACT COMPONENT SYSTEMMB711200910SERVICE MANUALNX-D7UX, NX-D7UN, NX-D7EE, NX-D7UW, NX-D7UH, NX-D5UG, NX-D5UX, NX-D5UN, NX-D5EE, NX-D5UW, NX-D5UHCOPYRIGHT 2009 Victor Company of Japan, LimitedLead free solder used in the bo

2、ard (material : Sn-Ag-Cu, melting point : 219 Centigrade)Lead free solder used in the board (material : Sn-Cu, melting point : 230 Centigrade)TABLE OF CONTENTS1 PRECAUTION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3、 . . . . . . . . 1-42 SPECIFIC SERVICE INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-73 DISASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4、 . . . . . . . . . 1-84 ADJUSTMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-175 TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5、 . . . . . . . . . . . . . . 1-18(for NX-D7) (for NX-D7/NX-D5)CA-NXD7SP-NXD7FSP-NXD7WSP-NXD7FSP-NXD7FSP-NXD7FSP-NXD7WSP-NXD7WSP-NXD7WCA-NXD51-2 (No.MB711)SPECIFICATIONAmplifier sectionOutput Power NX-D7 MAIN SPEAKERS 230 W (115 W + 115 W) at 3 (10% THD)SUBWOOFERS 230 W (115 W + 115 W) at 3 (10% THD)

6、NX-D5 MAIN SPEAKERS 230 W (115 W + 115 W) at 3 (10% THD)SUBWOOFERS 115 W at 3 (10% THD)Audio Input AUDIO IN: Stereo mini ( 3.5 mm)500 mV/47 k (at “AUDIO LVL3”)250 mV/47 k (at “AUDIO LVL2”)125 mV/47 k (at “AUDIO LVL1”)Digital Input/Output OPTICAL DIGITAL OUTPUT (output only) -21 dBm to -15 dBm (660 n

7、m 30 nm)NX-D7 Bluetooth ADPTUSB1:VIDEO/AUDIO PLAY (input only)USB2:AUDIO REC/PLAY (input and output)HDMI MONITOR OUT (output only)NX-D5 USB: REC/PLAY (input and output)HDMI MONITOR OUT (output only)VIDEO OUT Color system NTSC/PAL (interlaced/progressive)VIDEO (Composite) 1 V(p-p)/75 COMPONENT (Y) 1

8、V(p-p)/75 (PB/PR) 0.7 V(p-p)/75 HDMI MONITOR OUT 480p/576p/720p/1080i/1080pSpeaker impedance 3 - 16 Tuner sectionFM tuning range 87.50 MHz - 108.00 MHzAM tuning range 531 kHz - 1 710 kHz (at 9 kHz)530 kHz - 1 710 kHz (at 10 kHz)Disc player sectionRegion codes Middle East 2South East Asia 3Central an

9、d South America, Australia 4Dynamic range 80 dBHorizontal resolution 500 linesWow and flutter ImmeasurableUSB sectionRecording format MP3/WMA formatUSB specification Compatible with USB 2.0 Full SpeedCompatible device Mass storage classCompatible system FAT16, FAT32Bus power supply DC 5 V 500 mABlue

10、tooth section (NX-D7)Version Bluetooth ver. 2.0 + EDR Class 1/Class 2Compatible Bluetooth profile A2DP, AVRCPCommunication format 2.4 GHz FHSSHDMI sectionOutput power DC 5 V 55 mA(No.MB711)1-3Design and specifications are subject to change without notice.GeneralPower requirements AC 110 - 127/220 -

11、240 V , 50/60 HzFor Australia: AC 240 V , 50 Hz, For Russia: AC 230V , 50 HzPower consumption NX-D7 130 W (at operation)/21 W (at standby) /1 W or less (at ECO mode)NX-D5 85 W (at operation)/16 W (at standby) /1 W or less (at ECO mode)Dimensions (approx.) 195 mm 333 mm 313 mm (W H D)Mass (approx.) 3

12、.5 kgMain SpeakerType 3-way 3-speaker Bass Reflex Type (Magnetically-Shielded Type)Speaker units Tweeter 2.0 cm cone 1Mid Range 5.0 cm cone 1Woofer 16.0 cm cone 1Impedance 3 Power handling capacity 115 WFrequency range 40 Hz - 20 000 HzSound pressure level 84 dB/W/mDimensions (W H D) 205 mm 409.5 mm

13、 290.5 mmMass 3.6 kg eachSubwooferType 1-Way Bass Reflex Type (Magnetically-Shielded Type)Speaker units 16.0 cm cone 1Impedance 3 Power handling capacity 115 WFrequency range 40 Hz - 5 000 HzSound pressure level 83 dB/W/mDimensions (W H D) 205 mm 409.5 mm 290.5 mmMass 3.5 kg1-4 (No.MB711)SECTION 1PR

14、ECAUTION1.1 Safety Precautions(1) This design of this product contains special hardware andmany circuits and components specially for safety purpos-es. For continued protection, no changes should be madeto the original design unless authorized in writing by themanufacturer. Replacement parts must be

15、 identical tothose used in the original circuits. Services should be per-formed by qualified personnel only.(2) Alterations of the design or circuitry of the product shouldnot be made. Any design alterations of the product shouldnot be made. Any design alterations or additions will voidthe manufactu

16、rers warranty and will further relieve themanufacture of responsibility for personal injury or propertydamage resulting therefrom.(3) Many electrical and mechanical parts in the products havespecial safety-related characteristics. These characteris-tics are often not evident from visual inspection n

17、or can theprotection afforded by them necessarily be obtained by us-ing replacement components rated for higher voltage, watt-age, etc. Replacement parts which have these specialsafety characteristics are identified in the Parts List of Ser-vice Manual. Electrical components having such featuresare

18、identified by shading on the schematics and by ( ) onthe Parts List in the Service Manual. The use of a substitutereplacement which does not have the same safety charac-teristics as the recommended replacement parts shown inthe Parts List of Service Manual may create shock, fire, orother hazards.(4)

19、 The leads in the products are routed and dressed with ties,clamps, tubings, barriers and the like to be separated fromlive parts, high temperature parts, moving parts and/orsharp edges for the prevention of electric shock and firehazard. When service is required, the original lead routingand dress

20、should be observed, and it should be confirmedthat they have been returned to normal, after reassem-bling.(5) Leakage shock hazard testingAfter reassembling the product, always perform an isola-tion check on the exposed metal parts of the product (an-tenna terminals, knobs, metal cabinet, screw head

21、s,headphone jack, control shafts, etc.) to be sure the productis safe to operate without danger of electrical shock.Do notuse a line isolation transformer during this check. Plug the AC line cord directly into the AC outlet. Using a“Leakage Current Tester“, measure the leakage currentfrom each expos

22、ed metal parts of the cabinet, particular-ly any exposed metal part having a return path to thechassis, to a known good earth ground. Any leakage cur-rent must not exceed 0.5mA AC (r.m.s.). Alternate check methodPlug the AC line cord directly into the AC outlet. Use anAC voltmeter having, 1,000 per

23、volt or more sensitivityin the following manner. Connect a 1,500 10W resistorparalleled by a 0.15F AC-type capacitor between an ex-posed metal part and a known good earth ground.Measure the AC voltage across the resistor with the ACvoltmeter. Move the resistor connection to each exposed metalpart, p

24、articularly any exposed metal part having a returnpath to the chassis, and measure the AC voltage acrossthe resistor. Now, reverse the plug in the AC outlet andrepeat each measurement. Voltage measured any mustnot exceed 0.75 V AC (r.m.s.). This corresponds to 0.5mA AC (r.m.s.). 1.2 Warning(1) This

25、equipment has been designed and manufactured tomeet international safety standards.(2) It is the legal responsibility of the repairer to ensure thatthese safety standards are maintained.(3) Repairs must be made in accordance with the relevantsafety standards.(4) It is essential that safety critical

26、components are replacedby approved parts.(5) If mains voltage selector is provided, check setting for localvoltage.1.3 CautionBurrs formed during molding may be left over on some partsof the chassis. Therefore, pay attention to such burrs in the case of pre-forming repair of this system.1.4 Critical

27、 parts for safetyIn regard with component parts appearing on the silk-screenprinted side (parts side) of the PWB diagrams, the parts that areprinted over with black such as the resistor ( ), diode ( )and ICP ( ) or identified by the “ “ mark nearby are criticalfor safety. When replacing them, be sur

28、e to use the parts of thesame type and rating as specified by the manufacturer. (This regulation dose not Except the J and C version)Good earth groundPlace this probe on each exposedmetal part.AC VOLTMETER(Having 1000 ohms/volts,or more sensitivity)1500 10W0.15 F AC TYPE(No.MB711)1-51.5 Preventing s

29、tatic electricityElectrostatic discharge (ESD), which occurs when static electricity stored in the body, fabric, etc. is discharged, can destroy the laserdiode in the traverse unit (optical pickup). Take care to prevent this when performing repairs.1.5.1 Grounding to prevent damage by static electri

30、cityStatic electricity in the work area can destroy the optical pickup (laser diode) in devices such as laser products. Be careful to use proper grounding in the area where repairs are being performed. (1) Ground the workbenchGround the workbench by laying conductive material (such as a conductive s

31、heet) or an iron plate over it before placing thetraverse unit (optical pickup) on it.(2) Ground yourselfUse an anti-static wrist strap to release any static electricity built up in your body. (3) Handling the optical pickup In order to maintain quality during transport and before installation, both

32、 sides of the laser diode on the replacement opticalpickup are shorted. After replacement, return the shorted parts to their original condition. (Refer to the text.) Do not use a tester to check the condition of the laser diode in the optical pickup. The testers internal power source can easilydestr

33、oy the laser diode. 1.6 Handling the traverse unit (optical pickup)(1) Do not subject the traverse unit (optical pickup) to strong shocks, as it is a sensitive, complex unit. (2) Cut off the shorted part of the flexible cable using nippers, etc. after replacing the optical pickup. For specific detai

34、ls, refer to thereplacement procedure in the text. Remove the anti-static pin when replacing the traverse unit. Be careful not to take too long atime when attaching it to the connector. (3) Handle the flexible cable carefully as it may break when subjected to strong force. (4) I t is not possible to

35、 adjust the semi-fixed resistor that adjusts the laser power. Do not turn it.1.7 Attention when traverse unit is decomposed*Please refer to “Disassembly method“ in the text for the pickup unit. Apply solder to the short land sections before the card wire is disconnected from the connector on the ser

36、vo board. (If the card wireis disconnected without applying solder, the pickup may be destroyed by static electricity.) In the assembly, be sure to remove solder from the short land sections after connecting the card wire.1MConductive material(conductive sheet) or iron palate(caption)Anti-static wri

37、st strapSolder short land section1-6 (No.MB711)1.8 Important for laser products1.CLASS 1 LASER PRODUCT 2.CAUTION : (For U.S.A.) Visible and/or invisible class II laser radiationwhen open. Do not stare into beam.(Others) Visible and/or invisible class 1M laser radiationwhen open. Do not view directly

38、 with optical instruments. 3.CAUTION : Visible and/or invisible laser radiation whenopen and inter lock failed or defeated. Avoid directexposure to beam.4.CAUTION : This laser product uses visible and/or invisible laser radiation and is equipped with safety switches which prevent emission of radiati

39、on when the drawer is open and the safety interlocks have failed or are defeated. It is dangerous to defeat the safety switches.5.CAUTION : If safety switches malfunction, the laser is ableto function. 6.CAUTION : Use of controls, adjustments or performance of procedures other than those specified h

40、ere in may result in hazardous radiation exposure. REPRODUCTION AND POSITION OF LABELS and PRINT!Please use enough caution not to see the beam directly or touch it in case of an adjustment or operationcheck. WARNING LABEL and PRINT(No.MB711)1-7SECTION 2SPECIFIC SERVICE INSTRUCTIONSThis service manua

41、l does not describe SPECIFIC SERVICE INSTRUCTIONS.1-8 (No.MB711)SECTION 3DISASSEMBLY3.1 Main body (Used figure are NX-D7)3.1.1 Removing the Top cover (See Fig.1, 2 and 3)(1) Remove the five screws A and one screw B attaching theSide panel. (See Fig.1)Fig.1(2) Remove the six screws C attaching the bo

42、th side of theSide panel and then side to backward to remove the Sidepanel. (See Fig.2)Fig.2(3) Disengage two hooks a engaged both side of the Top cov-er. (See Fig.3)Fig.33.1.2 Removing the Rear panel (See Fig.4, 5)(1) Disconnect the card wire from Tuner pack connected toconnector CN306 of the Main

43、board. (See Fig.4)(2) Disconnect the connector wire from FAN connected to con-nector CN303 of the Main board. (See Fig.4)Fig.4A ABChook aCN306CN303(No.MB711)1-9(3) Remove the two screws D attaching the Main board. (See Fig.5)(4) Remove the one screw E attaching the DVD board. (See Fig.5)(5) Remove t

44、he two screws F attaching the Mecha chassis.(See Fig.5)(6) Remove the two screws G attaching the Amp board. (See Fig.5)(7) Remove the two screws H attaching the Voltage selectorboard. (See Fig.5)Fig.53.1.3 Removing the Main board (See Fig.6)(1) Disconnect t the card wire from USB board connected toc

45、onnector CN502 of the Main board.(2) Disconnect the card wires from Ripping module board con-nected to connectors CN305 and CN501 of the Mainboard.(3) Disconnect the card wire from Loader board connected toconnector CN307 of the Main board.(4) Disconnect the connector wire from Power board connect-e

46、d to connector CN180 of the Main board.(5) Disconnect the card wire from DVD board connected toconnector CN500 of the Main board.(6) Disconnect the card wire from Amp board connected toconnector CN503 of the Main board.(7) Disconnect the card wires from DVD board connected toconnectors CN310 and CN3

47、08 of the Main board.(8) Disconnect the parallel wire from Amp board connected toconnector CN181 of the Main board.(9) Disconnect the card wire from Mic board connected to con-nector CN304 of the Main board.(10) Disconnect the card wires from Front panel connected toconnectors CN301 and CN312 of the

48、 Main board.(11) Disconnect the parallel wire from Front panel connected toconnector CN315 of the Main board.(12) Remove the two screws J attaching the Main board.Fig.63.1.4 Removing the DVD mechanism (See Fig.7, 8)(1) Disconnect the connector wire from USB board connectedto connector CN811 of the D

49、VD board. (See Fig.7)Fig.7DEFHFGCN502CN500CN503CN310CN308CN181CN304CN305CN307CN301 CN315CN180CN312CN501JJCN8111-10 (No.MB711)(2) Disconnect the connector wire from USB board connectedto connector CN801 of the Connection board. (See Fig.8)(3) Remove the two screws K attaching the both side of theDVD mechanism. (See Fig.8)(4) Disengaged two hooks b engaged both side of the DVDmechanism, (See Fig.8)Fig.83.1.5 Removing the Front panel (See Fig.9, 10)(1) Remove the two screws L attaching the Front