Splawn_manual_rev_2_4 电路图 维修原理图.pdf

《Splawn_manual_rev_2_4 电路图 维修原理图.pdf》由会员分享，可在线阅读，更多相关《Splawn_manual_rev_2_4 电路图 维修原理图.pdf（13页珍藏版）》请在收音机爱好者资料库上搜索。

1、OWNERS MANUAL RODUICKQMODROP& 收音机爱好者资料库 Ra d i o Fa n s .CN POWER ON STANDBY ON PRESENCEBASSMIDDLETREBLESOLOVOLUME bySplawn GAINGAINVOLUMETREBLEBASS _CLEAN CHANNEL_OVERDRIVE CHANNEL_ ROD MODE 1st Gear 2nd Gear 3rd Gear UICKQ Thank you for purchasing your new Splawn amplifier. We have put together a

2、little information that will help you understand the amp and all of its functions. All of our amps are built in our shop in Dallas NC right here in the USA. We build all of our speaker cabs and head boxes in house. Some parts of the amplifier are out sourced such as the chassiss, circuit boards and

3、transformers. The transformers are custom wound by Heyboer and are also made in the USA. We hope that this amplifier will give you years of tonal pleasure. Quickrod & Pro Mod Front Panel Controls 1. Power Switch-Switches main AC power on or off 2. Standby Switch 3. Presence Control 4. Bass Control 5

4、. Middle Control 6. Treble Control 7. Solo Volume 8. Master Volume 9. Gain Control 10. Mode Switch 11. Clean Bass Control 12. Clean Treble Control 13. Clean Volume Control 14. Clean Gain Control -Switches the high voltage on or off -High frequency control on the output section -Controls the bass fre

5、quency on the overdrive channel -Controls the middle frequency on the overdrive channel -Controls the treble frequency on the overdrive channel -Switchable volume control on the overdrive channel activated by the footswitch -Controls the overall volume of the overdrive channel -Controls the amout of

6、 pre-amp gain to the overdrive channel -Three position switch that gives different pre-amp styles -Controls the bass frequency on the clean channel -Controls the treble frequency on the clean channel -Controls the overall volume of the clean channel -Controls the amount of pre-amp gain to the clean

7、channel (1st gear Classic ) (2nd gear Hot rodded) (3rd gear Super Hot rodded) Splawn Amplification 115 South Gaston St. Dallas, NC 28034 704-922-0020 收音机爱好者资料库 Ra d i o Fa n s .CN Quickrod & Pro Mod Rear Panel Controls 1. Footswitch A-TRS 1/4 Jack Tip switches Solo Volume- Ring switches OD1/OD2 2. F

8、ootswitch B 3.Series Effects Loop Level Switch 4. Series Effects Loop Bypass Switch 5. Series Effects Loop Return Jack 6. Series Effects Loop Send Jack 7. Half Power Switch 8. Speaker Outputs 9. Impedence Selector 10. Main Voltage Selector 11. Main Fuse 12. High Tension Fuse -TRS 1/4 Jack Tip switch

9、es Clean/Overdrive- Ring switches Mode Switch -+4db -10db switch for matching line levels to effects units -True bypass switch -Connection from the output of the effects device -Connection to the input of the effects device -Disconnects the outside power tubes -Connection to the speaker cabinet (nev

10、er run a tube amp without a speaker) -4/8/16 ohm selector to match the load of the speaker cabinet -100/120/220/240 voltage selector to match the input voltage -Use 4 amp 250 volt fuse for 100 or 120 volt setting Use 2 amp 250 volt fuse for 220/240 volt setting -Use 1 amp 250 volt Slow Blow Fuse FOO

11、TSWITCH AB LEVELBYPASSRETURNSEND OUT/+4 dbOUT/BYPASS IN/-10 dbIN/ACTIVE EFFECTS LOOPSPEAKERS 4 8 16 OUTPUT SELECTOR VOLTAGE MAINS INPUTMAINS FUSE 4A 120V HT FUSE 1A Slow-Blow 100 WATT RMS HALF POWER FULL POWER bySplawn 2A 220/240V 100v-120v 220v-240v UICKODQR always set the amps impedence to half of

12、 the speaker cabs impedence when using half power 12345678 1. Pre-amp tube - 12AX7 2nd gain stage of the clean channel 2. Pre-amp tube 3. Pre-amp tube 4. Pre-amp tube 5. Power Tube 6. Power Tube 7. Power Tube -12AX7 Side A 1st gain stage for clean & OD channels - Side B 2nd gain stage of OD channel

13、-12AX7 Side A 3rd gain stage of OD channel - Side B 4th gain stage of OD channel -12AX7 Phase Inverter - EL34/KT77 (Quickrod) - KT88/6550 (Pro Mod) - EL34/KT77 (Quickrod) - KT88/6550 (Pro Mod) - EL34/KT77 (Quickrod) - KT88/6550 (Pro Mod) 8. Power Tube- EL34/KT77 (Quickrod) - KT88/6550 (Pro Mod) Tube

14、 Layout 收音机爱好者资料库 Ra d i o Fa n s .CN Quickrod & ProMod Footswitch Operation 1. Clean/Overdrive Switch-Blue LED on indicates Clean Channel - Blue Led off indicates OD Channel 2. Overdrive 1 / Overdrive 2 Switch 3. Solo Boost Switch -Amber LED on indicates OD2 gain boost - LED off indicates OD1 -Gree

15、n LED on indicates Solo Volume control activated - OD2 also is activated Overdrive 1/ Overdrive 2Clean/OverdriveSolo Boost Footswitch connections - Two 1/4 TRS plugs on a 25 cable Setting up the Amplifier: After unpacking your new amp, Turn the amp around so the back faces you. Remove the four screw

16、s to remove the back cover of the amp. You will find the tubes packaged tightly on the left side of the Amp. Carefully remove the package and remove the tubes. You will have three preamp tubes and four power section tubes. Power Section Tubes: Un-box the Power section tubes. Keep the boxes! They are

17、 marked with tube ratings! You will see on the base of the tube there is a “key” guide to align the tube into the socket. Starting with the tube socket on the far right, Line up the key with the slot in the socket, From the top of the tube, firmly press the tube into the socket until the base of the

18、 tube is flush with the Socket. Insert these tubes into the tube sockets. The tubes are matched so you may install them in no particular order. After you install a tube carefully hold the tube spring retainer and stretch it over the top of the tube and center it. These are light metal and can bend.

19、If you happen to bend them you can shape it to the tube while its installed. Reinstall the rear cover and get ready to fire this monster amplifier to life! WARNING: Please Check the Voltage selector on the back for proper Voltage selection! Please check the volume control levels on all channels befo

20、re powering on. After you plug in the amplifier, Flip the power switch down to turn on. Wait for a minute for the tubes to warm, then turn on the Standby switch. The Amp is ready for explosive guitar sounds! This Amplifier will get VERY loud. Remember you only have one set of ears! Limited Lifetime

21、Warranty. New Amplifiers are lifetime warranted to the original purchaser against failure of materials and workmanship. No other warranty applies. Tubes, transformers and speakers are warranted for a period of ninety days. This warranty applies only if the amplifier has not been damaged by accident,

22、 misuse or as a result of repair or modification. Splawn reserves the right to make any design changes without notice or obligation to incorporate these changes in products previously purchased. Splawn Amplification 115 South Gaston St. Dallas, NC 28034 Dimensions 29” Wide, 11.5” Tall, 8.5” Deep, 50

23、lbs OWNERS MANUAL NITRO POWER ON STANDBY ON RESONANCEPRESENCEBASSMIDDLETREBLESOLO bySplawn VOLUMEGAINVOLUMETREBLEBASS _CLEAN CHANNEL_OVERDRIVE CHANNEL_ GAIN N Thank you for purchasing your new Splawn amplifier. We have put together a little information that will help you understand the amp and all o

24、f its functions. All of our amps are built in our shop in Dallas NC right here in the USA. We build all of our speaker cabs and head boxes in house. Some parts of the amplifier are out sourced such as the chassiss, circuit boards and transformers. The transformers are custom wound by Heyboer and are

25、 also made in the USA. We hope that this amplifier will give you years of tonal pleasure. Nitro Front Panel Controls 1. Power Switch-Switches main AC power on or off 2. Standby Switch 4. Presence Control 5. Bass Control 6. Middle Control 7. Treble Control 8. Solo Volume 9. Master Volume 10. Gain Con

26、trol 11. Clean Bass Control 12. Clean Treble Control 13. Clean Volume Control 14. Clean Gain Control -Switches the high voltage on or off -High frequency control on the output section -Controls the bass frequency on the overdrive channel -Controls the middle frequency on the overdrive channel -Contr

27、ols the treble frequency on the overdrive channel -Switchable volume control on the overdrive channel activated by the footswitch -Controls the overall volume of the overdrive channel -Controls the amout of pre-amp gain to the overdrive channel -Controls the bass frequency on the clean channel -Cont

28、rols the treble frequency on the clean channel -Controls the overall volume of the clean channel -Controls the amount of pre-amp gain to the clean channel Splawn Amplification 115 South Gaston St. Dallas, NC 28034 704-922-0020 3. Resonance Control-Low frequency control on the output section ITRO Nit

29、ro Rear Panel Controls 1. Footswitch A-TRS 1/4 Jack Tip switches Solo Volume- Ring switches OD1/OD2 2. Footswitch B 3.Series Effects Loop Level Switch 4. Series Effects Loop Bypass Switch 5. Series Effects Loop Return Jack 6. Series Effects Loop Send Jack 7. Half Power Switch 8. Speaker Outputs 9. I

30、mpedence Selector 10. Main Voltage Selector 11. Main Fuse 12. High Tension Fuse -TRS 1/4 Jack Tip switches Clean/Overdrive -+4db -10db switch for matching line levels to effects units -True bypass switch -Connection from the output of the effects device -Connection to the input of the effects device

31、 -Disconnects the outside power tubes -Connection to the speaker cabinet (never run a tube amp without a speaker) -4/8/16 ohm selector to match the load of the speaker cabinet -100/120/220/240 voltage selector to match the input voltage -Use 4 amp 250 volt fuse for 100 or 120 volt setting Use 2 amp

32、250 volt fuse for 220/240 volt setting -Use 1 amp 250 volt Slow Blow Fuse FOOTSWITCH AB LEVELBYPASSRETURNSEND OUT/+4 dbOUT/BYPASS IN/-10 dbIN/ACTIVE EFFECTS LOOPSPEAKERS 4 8 16 OUTPUT SELECTOR VOLTAGE MAINS INPUTMAINS FUSE 4A 120V HT FUSE 1A Slow-Blow 100 WATT RMS HALF POWER FULL POWER bySplawn 2A 2

33、20/240V 100v-120v 220v-240v N always set the amps impedence to half of the speaker cabs impedence when using half power 12345678 1. Pre-amp tube - 12AX7 2nd gain stage of the clean channel 2. Pre-amp tube 3. Pre-amp tube 4. Pre-amp tube 5. Power Tube 6. Power Tube 7. Power Tube -12AX7 Side A 1st gai

34、n stage for clean & OD channels - Side B 2nd gain stage of OD channel -12AX7 Side A 3rd gain stage of OD channel - Side B 4th gain stage of OD channel -12AX7 Phase Inverter - EL34/KT77 - KT88/6550 - EL34/KT77 - KT88/6550 - EL34/KT77 - KT88/6550 8. Power Tube- EL34/KT77 - KT88/6550 Tube Layout ITRO N

35、itro Footswitch Operation 1. Clean/Overdrive Switch-Blue LED on indicates OD Channel - Blue LED off indicates Clean Channel 2. Overdrive 1 / Overdrive 2 Switch 3. Solo Boost Switch -Blue LED on indicates OD2 gain boost - LED off indicates OD1 -Blue LED on indicates Solo Volume control activated Over

36、drive 1/ Overdrive 2Clean/OverdriveSolo Boost Footswitch connections - Two 1/4 TRS plugs on a 25 cable Setting up the Amplifier: After unpacking your new amp, Turn the amp around so the back faces you. Remove the four screws to remove the back cover of the amp. You will find the tubes packaged tight

37、ly on the left side of the Amp. Carefully remove the package and remove the tubes. You will have three preamp tubes and four power section tubes. Power Section Tubes: Un-box the Power section tubes. Keep the boxes! They are marked with tube ratings! You will see on the base of the tube there is a “k

38、ey” guide to align the tube into the socket. Starting with the tube socket on the far right, Line up the key with the slot in the socket, From the top of the tube, firmly press the tube into the socket until the base of the tube is flush with the Socket. Insert these tubes into the tube sockets. The

39、 tubes are matched so you may install them in no particular order. After you install a tube carefully hold the tube spring retainer and stretch it over the top of the tube and center it. These are light metal and can bend. If you happen to bend them you can shape it to the tube while its installed.

40、Reinstall the rear cover and get ready to fire this monster amplifier to life! WARNING: Please Check the Voltage selector on the back for proper Voltage selection! Please check the volume control levels on all channels before powering on. After you plug in the amplifier, Flip the power switch down t

41、o turn on. Wait for a minute for the tubes to warm, then turn on the Standby switch. The Amp is ready for explosive guitar sounds! This Amplifier will get VERY loud. Remember you only have one set of ears! Limited Lifetime Warranty. New Amplifiers are lifetime warranted to the original purchaser aga

42、inst failure of materials and workmanship. No other warranty applies. Tubes, transformers and speakers are warranted for a period of ninety days. This warranty applies only if the amplifier has not been damaged by accident, misuse or as a result of repair or modification. Splawn reserves the right t

43、o make any design changes without notice or obligation to incorporate these changes in products previously purchased. Splawn Amplification 115 South Gaston St. Dallas, NC 28034 Dimensions 29” Wide, 11.5” Tall, 8.5” Deep, 50lbs OWNERS MANUAL CSTOCKP&ROOMPETITION POWER ON STANDBY ON PRESENCEBASSMIDDLE

44、TREBLESOLOVOLUME bySplawn GAIN _OVERDRIVE CHANNEL_ COMPETITION MODE 1st Gear 2nd Gear 3rd Gear Thank you for purchasing your new Splawn amplifier. We have put together a little information that will help you understand the amp and all of its functions. All of our amps are built in our shop in Dallas

45、 NC right here in the USA. We build all of our speaker cabs and head boxes in house. Some parts of the amplifier are out sourced such as the chassiss, circuit boards and transformers. The transformers are custom wound by Heyboer and are also made in the USA. We hope that this amplifier will give you

46、 years of tonal pleasure. Competition & Pro Stock Front Panel Controls 1. Power Switch-Switches main AC power on or off 2. Standby Switch 3. Presence Control 4. Bass Control 5. Middle Control 6. Treble Control 7. Solo Volume 8. Master Volume 9. Gain Control 10. Mode Switch -Switches the high voltage

47、 on or off -High frequency control on the output section -Controls the bass frequency on the overdrive channel -Controls the middle frequency on the overdrive channel -Controls the treble frequency on the overdrive channel -Switchable volume control on the overdrive channel activated by the footswit

48、ch -Controls the overall volume of the overdrive channel -Controls the amout of pre-amp gain to the overdrive channel -Three position switch that gives different pre-amp styles (1st gear Classic ) (2nd gear Hot rodded) (3rd gear Super Hot rodded) Splawn Amplification 115 South Gaston St. Dallas, NC 28034 704-922-0020 Competition & Pro Stock Rear Panel Controls 1. Footswitch A-TRS 1/4 Jack Tip switches Solo Volume- Ring switches OD1/OD2 2. Footswitch B 3.Series Effects Loop Level Switch 4. Series Effects Loop Bypass Switch 5. Series Effects Loop Return Jack 6. Series Ef