Fender_vibrasonic 电路图 维修原理图.pdf
《Fender_vibrasonic 电路图 维修原理图.pdf》由会员分享,可在线阅读,更多相关《Fender_vibrasonic 电路图 维修原理图.pdf(9页珍藏版)》请在收音机爱好者资料库上搜索。
1、“CUSTOM” VIBRASONIC AMP p/n 021-5200-000 (120V) SERVICE MANUAL CONTENTS: Notices Specifications Theory of operation Parts lists: PCB assembly Chassis assembly Cabinet assembly Footswitch assembly Miscellaneous Schematics/diagrams Fender Musical Instruments Corp. 7975 North Hayden Road Scottsdale, AZ
2、 85258 收音机爱好者资料库 Ra d i o Fa n s .CN “CUSTOM” VIBRASONIC (This is the model name for warranty claims) SERVICE MANUAL NOVEMBER 1995 IMPORTANT NOTICE: The information contained herein is CONFIDENTIAL and PROPRIETARY to Fender Musical Instruments Corp. It is disclosed solely for use by qualified techni
3、cians for purposes of equipment maintenance and service. It is not to be disclosed to others without the expressed permission of Fender Musical Instruments Co. All specifications subject to change without notice. For warranty repair service, only Fender specified part numbers are to be used. It is r
4、ecommended they also be used for post-warranty maintenance and repair. Parts marked with an asterisk (*) indicate the required use of that specific part. This is necessary for RELIABILITY and SAFETY requirements. DO NOT USE A SUBSTITUTE! A coded naming convention is used in the description of certai
5、n parts. The codes and what they mean are as follows: CAPACITOR CODES HARDWARE CODES CAP AE=Aluminum ElectrolyticBLX=Black Oxide CAP CA=Ceramic AxialCR=Chrome Plated CAP CD=Ceramic DiskHWH=Hex Washer Head CAP MPF=Metalized Polyester FilmM=Machine Screw CAP MY=MylarNI=Nickel Plated CAP PFF=Polyester
6、Film/FoilOHP=Oval Head Phillips PB=Particle Board RESISTOR CODESPHP=Pan Head Phillips PHPS=Pan Head Phillips Sems RES CC=Carbon CompSMA=Sheet Metal A Point RES CF=Carbon FilmSMB=Sheet Metal B Point RES FP=Flame ProofSS=Stainless Steel RES MF=Metal FilmTF=Thread Forming RES WW=Wire WoundZI=Zinc Plate
7、d 收音机爱好者资料库 Ra d i o Fa n s .CN “CUSTOM” VIBRASONIC SPECIFICATIONS Product Release No.:PR 186 (This is not a model number) Part Number:120V Version :021-5200-000 Input impedance:Input 1, both channels1m Input 2, both channels132k Power Output:85 Watts RMS minimum 5% THD Rated load impedance:4 Speake
8、r Complement:(1) 15” “Special Design” (p/n 049135) Dimensions:Height:22(55.9 cm) Width: 26 5/32(66.4 cm) Depth: 10 3/8(26.4 cm) Weight:71 lbs.(32.3 kg) Product specifications are subject to change without notice 收音机爱好者资料库 Ra d i o Fa n s .CN “CUSTOM” VIBRASONIC THEORY OF OPERATION STEEL CHANNEL J1 i
9、s the high sensitivity input and J2 is the low sensitivity input. The input is fed to V1A, which proveds a gain of about 42. The output from V1A drives the Treble (R7), Mid(R9), and Bass(R7) tone controls, then feeds the Volume control (R10). When engaged, the SWEET switch connects C5 to the wiper o
10、f the VOLUME control. This provides a boost in the high frequencies. The “Sweet” feature is most noticeable at lower volume settings. The signal then feeds to V1B, which provides a gain of about 66. GUITAR CHANNEL J3 is the high sensitivity input and J4 is the low sensitivity input. V2A contains the
11、 FAT switch which boosts the gain mostly at lower and mid frequencies. V2A drives the tone controls, and the Volume control (R21) feeds V2B. V1B and V2B share the same cathode resistor (R23) and bypass capacitor (C11). The output of the Steel channel (V1B pin 6) sums with the output of the GUITAR ch
12、annel at V2B pin 6. From that point the signal follows two paths. One to the reverb drive stage (V3). The other through R32 to summing amp V4B. REVERB V3 (12AT7) provides a gain of about 33 to drive the reverb transformer. V4A is the Reverb recovery or sense stage. The Reverb control (R29) determine
13、s the amount of reverb signal that is summed with the dry signal at V4B. Via the footswitch, the Reverb can be disabled by grounding the signal at the node between R30 and R74. VIBRATO V5A is a low frequency oscillator. The Speed control (R56) varies the oscillation frequency. V5B is the Neon Lamp d
14、river. The lamp flashes faster or slower based on the position of the Speed control (R56). The brightness of the neon bulb is sensed by the LDR (Light Dependent Resistor). The LDR connects to the Intensity control (R64) which varies the amount of low frequency modulation applied to the input of the
15、Phase Inverter(V6). POWER AMPLIFIER The output from V4B feeds the Phase Inverter(V6), which is a classic style split-load type, used without feedback. The output tubes (5881/6L6WGC) are arranged in a push-pull configuration that will produce 85 watts minimum into a four(4) load at 5% THD. PARTS LIST
16、 PRINTED CIRCUIT BOARD ASSEMBLY QTY PART # DESCRIPTION REFERENCE DESIGNATION 1049266PCB ASSY CUSTOM VIBRASONIC ALLV(STUFFED) 3037805CABLE RIBBON 6CKT 2-1/4” 1031069CAP AE RDL 10uF 100v 20%C37 5028465CAP AE RDL 22uF 25V 20%C6 C11 C14 C27 C28 1036954CAP AE RDL 22uF 63V 20%C36 3024819CAP AE AX 22uF 500
17、v 20%C32 C33 C34 1031040CAP AE RDL 100uF 100V 20%C35 2013638CAP AE AX 200uF 285V 20%C30 C31 2025979CAPCD 50pF 1KV 10%C5 C10 1031780CAP SLVR MICA 150PF 300VC7 1007029CAPCD 220pF 1KV 10%C38 1020917CAPCD 250pF 1KV 10%C2 1020842CAPCD 500pF 1KV 10%C13 1047065CAP PFF RDL .0015uF 100VC16 1037666CAP PFF .00
18、1 uF 400v 10%C20 2024823CAP MPF RDL .01uF 400V 10%C25 C26 “CUSTOM” VIBRASONIC PRINTED CIRCUIT BOARD ASSEMBLY (CONT) QTY PART # DESCRIPTION REFERENCE DESIGNATION 2024833CAP MPF RDL .022UF 400V 10%C12 C24 2024835CAP MPF RDL .022UF 630V 10%C9 C40 1024845CAP MPF RDL .047UF 400V 10%C4 1024846CAP MPF RDL
19、.047UF 630VC8 1024853CAP MPF RDL .1UF 250V 10%C21 2024854CAP MPF RDL .1UF 400V 10%C3 C19 2024855CAP MPF RDL .1UF 630V 10%C22 C23 2037596CONTROL SNAPIN 1M 30AR10 R21 (VOLUME) 1037601CONTROL SNAPIN 3M 30CR56 (SPEED) 1028421CONTROL 100 D FOJ SCREW ADJR69 (HUM BALANCE) 1017502CONTROL 10K B SCREW ADJR71
20、(BIAS ADJUST) 2037598CONTROL SNAPIN 10K 10AR9 R20 (MID) 1037602CONTROL SNAPIN 50K 30CR64 (INTENSITY) 1037600CONTROL SNAPIN 100K BR29 (REVERB) 2037599CONTROL SNAPIN 250K 10AR8 R19 (BASS) 2037597CONTROL SNAPIN 250K 30AR7 R18 (TREBLE) 1064089DIODE 1N4003 200PRV 1AMPCR5 4026730DIODE 1N4006/1N5062 800PRV
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- Fender_vibrasonic 电路图 维修原理图 维修 原理图