HarmanKardon-HK3490-rec-sch维修电路原理图.pdf
《HarmanKardon-HK3490-rec-sch维修电路原理图.pdf》由会员分享,可在线阅读,更多相关《HarmanKardon-HK3490-rec-sch维修电路原理图.pdf(108页珍藏版)》请在收音机爱好者资料库上搜索。
1、harman/kardon HK3490 HK3490 STEREO RECEIVER SERVICE MANUAL CONTENTS ESD WARNING.2 LEAKAGE TESTING.3 BASIC SPECIFICATIONS.4 PACKAGING.5 FRONT PANEL CONTROLS.6 REAR PANEL CONNECTIONS.8 REMOTE CONTROL FUNCTIONS.11 CONNECTIONS/INSTALLATION.14 OPERATION.21 TROUBLESHOOTING GUIDE.26 PROCESSOR RESET.26 DISA
2、SSEMBLY.27 UNIT EXPLODED VIEW.30 EXPLODED VIEW PARTS LIST31 AMP BIAS ADJUSTMENT.32 BLOCK DIAGRAM.33 PCB DRAWINGS34 ELECTRICAL PARTS LIST.40 SEMICONDUCTOR PINOUTS.63 SCHEMATICS.104 WIRING DIAGRAM.108 harman/kardon, Inc. 250 Crossways Park Dr. Released 2008 Woodbury, New York 11797 Rev0 6/2008 Discont
3、inued XXXX RadioFans.CN 收音机爱 好者资料库Eachprecautioninthismanualshouldbefollowedduringservicing.Components identified with the IEC symbolin the parts list are special significance to safety. When replacing a component identified with, use only the replacement parts designated, or parts with the same rat
4、ings or resistance, wattage, or voltage that are designated in theparts list in this manual. Leakage-current or resistance measurements must be made to determine that exposed parts are acceptablyinsulated from the supply circuit before retuming the product to the customer.Some semiconductor (solid s
5、tate) devices can be damaged easily by static electricity. Such components commonly are calledElectrostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field effect transistors andsemiconductor chip components.The following techniques should be used to
6、 help reduce the incidence of component damage caused by static electricity.1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any electrostatic charge onyour body by touching a known earth ground. Alternatively, obtain and wear a commercially av
7、ailable discharging wrist strap device,which should be removed for potential shock reasons prior to applying power to the unit under test.2. After removing an electrical assembly equipped with ES devices, place the assembly on a conductive surface such as aluminum foil, toprevent electrostatic charg
8、e build-up or exposure of the assembly.3. Use only a grounded-tip soldering iron to solder or unsolder ES devices.4. Use only an anti-static solder removal device. Some solder removal devices not classified as anti-static can generate electrical chargessufficient to damage ES devices.5. Do not use f
9、reon-propelled chemicals. These can generate electrical change sufficient to damage ES devices.6. Do not remove a replacement ES device from its protective package until immediately before you are ready to install it. (Most replacementES devices are packaged with leads electrically shorted together
10、by conductive foam, aluminum foil or comparable conductive material.)7. Immediately before removing the protective material from the leads of a replacement ES device, touch the protective material to thechassis or circuit assembly into which the device will be installed.Be sure no power is applied t
11、o the chassis or circuit, and observe all other safety precautions.8. Minimize bodily motions when handling unpackaged replacement ES devices. (Otherwise harmless motion such as the brushing togetheror your clothes fabric or the lifting of your foot from a carpeted floor can generate static electric
12、ity sufficient to damage an ES devices.CAUTION :HK3490 harman/kardonharman/kardon RadioFans.CN 收音机爱 好者资料库21. Inspect all lead dress to make certain thatleads are not pinched or that hardware is notlodged between the chassis and other metalpartsintheunit.2. Be sure that any protective devices such as
13、nonmetallic control knobs, insulating fish-papers,cabinetbacks,adjustmentandcompartment covers or shields, isolationresistor-capacitynetworks,mechanicalinsulators, etc. Which were removed for theservicingareproperlyre-installed.Before returning the unit to the user, perform the following safety chec
14、ks :3. Be sure that no shock hazard exists ; check for leakagecurrentusingSimpsonModel229LeakageTester,standardequipment item No. 21641, RCA Model WT540A or usealternate method asfollows : Plug the power cord directlyInto a 120 volt AC receptacle (do not use an IsolationTransformer for this test). U
15、sing two clip leads, connect a1500ohms,10wattResistorparalleledbya0.15uFcapacitor,inserieswithallexposedmetalcabinetpartsandaknownearthground,suchas a water pipe or conduit. Use a VTVM or VOM with 1000 ohms per volt, or higher sensitivity to measure the AC voltage drop across theresistor. (See diagr
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- HarmanKardon HK3490 rec sch 维修 电路 原理图