索尼 sony_MZ-E10_service_manual 电路图 维修手册.pdf

《索尼 sony_MZ-E10_service_manual 电路图 维修手册.pdf》由会员分享，可在线阅读，更多相关《索尼 sony_MZ-E10_service_manual 电路图 维修手册.pdf（40页珍藏版）》请在收音机爱好者资料库上搜索。

1、Battery life 1) (Unit: Approx. hours) (JEITA 2) ) Batteries SP Stereo LP2 LP4 (normal) Stereo Stereo Lithium-ion 23 33 40 built-in rechargeable battery 3) 1)Measured with the power save function on (see“ Preserving battery power” ). 2)Measured in accordance with the JEITA (Japan Electronics andInfor

2、mation Technology Industries Association) standard (using a SonyMDW-series Mini-disc). 3)With a fully charged battery. Note The battery life may be shorter than that specified, depending on the operating conditions,the temperature of the location. Dimensions Approx. 81.9 x 72.2 x 9.9 mm (w/h/d) ( 3

3、1 /4 x 2 7 /8 x 13 /32 in.) (not including projecting parts and controls) Mass Approx. 55 g (1.6 oz) (including the built-in rechargeable battery) Supplied accessories Headphones/earphones with a remote control (1) Battery charging stand (1) AC power adaptor (for the supplied battery charging stand)

4、 (1) Headphone adaptor (1) Carrying pouch (1) Design and specifications are subject to change without notice. MZ-E10 SERVICE MANUAL PORTABLE MINIDISC PLAYER SPECIFICATIONS US Model Canadian Model AEP Model UK Model E Model Tourist Model Model Name Using Similar Mechanism NEW MD Mechanism Type MT-MZE

5、10-184 Optical Pick-up Mechanism Type ABX-1ES US and foreign patents licensed from Dolby Laboratories Licensing Corporation Ver 1.0 2002.11 9-874-219-01 2002K0200-1 2002.11 Sony Corporation Personal Audio Company Published by Sony Engineering Corporation Audio playing system MiniDisc digital audio s

6、ystem Laser diode properties Material: GaAlAs Wavelength: = 790 nm Emission duration: continuous Laser output: less than 44.6 W* * This output is the value measured at a distance of 200 mm from theobjective lens surface on the optical pick-up block with 7 mm aperture. Revolutions Approx. 300 rpm to

7、2,700 rpm Error correction ACIRC (Advanced Cross Interleave Reed Solomon Code) Sampling frequency 44.1 kHz Coding ATRAC (Adaptive TRansform Acoustic Coding) ATRAC3: LP2/LP4 Modulation system EFM (Eight to Fourteen Modulation) Number of channels 2 stereo channels 1 monaural channel Frequency response

8、 20 to 20,000 Hz 3 dB Outputs Headphones/earphones: dedicated headphone/ remote control jack, output level 5 mW + 5 mW(US model) load impedance 16 ohms, 5 mW + 5 mW (Other models) load impedance 16 ohms Power requirements Lithium-ion rechargeable battery (Built-in: LIP- 3WMB, 3.7 V , 340 mAh, Li-ion

9、) External power jack (for the battery charging stand): Power rating 6 V DC2 MZ-E10 Specifications . 1 1. SERVICING NOTE . 3 2. GENERAL Playing an MD . 4 3. DISASSEMBLY 3-1. Panel assy (S), Upper . 5 3-2. Mechanism Deck (MT-MZE10-184) . 5 3-3. Bracket assy . 6 3-4. Power Board, Main Board . 6 3-5. C

10、ontrol Board . 7 3-6. Optical Pick-up assy(ABX-1ES) . 7 4. TEST MODE. 8 5. ELECTRICAL ADJUSTMENTS .11 6. DIAGRAMS 6-1. Block Diagram . 19 6-2. Printed Wiring Boards Main Section (1/2) . 20 6-3. Printed Wiring Boards Main Section (2/2) . 21 6-4. Schematic Diagram Main Section (1/3) . 22 6-5. Schemati

11、c Diagram Main Section (2/3) . 23 6-6. Schematic Diagram Main Section (3/3) . 24 6-7. IC Pin Function Descrintion . 26 6-8. IC Block Diagrams . 30 7. EXPLODED VIEWS 7-1. Main Section . 33 7-2. Mechanism Deck Section (MT-MZE10-184) . 34 8. ELECTRICAL PARTS LIST . 35 SAFETY-RELATED COMPONENT WARNING!

12、COMPONENTS IDENTIFIED BY MARK ! OR DOTTED LINE WITH MARK !ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY. Flexible Circuit Board Repairing K

13、eep the temperature of the soldering iron around 270C during repairing. Do not touch the soldering iron on the same conductor of the circuit board (within 3 times). Be careful not to apply force on the conductor when soldering or unsoldering. Notes on chip component replacement Never reuse a disconn

14、ected chip component. Notice that the minus side of a tantalum capacitor may be dam- aged by heat. TABLE OF CONTENTS * Replacement of SN761058ZQL (IC501) and LC896442-VH4- 16-E (IC601) used in this set requires a special tool. CAUTION Use of controls or adjustments or performance of procedures other

15、 than those specified herein may result in hazardous radiation exposure. rUNLEADED SOLDER Boards requiring use of unleaded solder are printed with the lead-free mark (LF) indicating the solder contains no lead. (Caution: Some printed circuit boards may not come printed with the lead free mark due to

16、 their particular size.): LEAD FREE MARK Unleaded solder has the following characteristics. Unleaded solder melts at a temperature about 40C higher than ordinary solder. Ordinary soldering irons can be used but the iron tip has to be applied to the solder joint for a slightly longer time. Soldering

17、irons using a temperature regulator should be set to about 350C. Caution: The printed pattern (copper foil) may peel away if the heated tip is applied for too long, so be careful! Strong viscosity Unleaded solder is more viscous (sticky, less prone to flow) than ordinary solder so use caution not to

18、 let solder bridges occur such as on IC pins, etc. Usable with ordinary solder It is best to use only unleaded solder but unleaded solder may also be added to ordinary solder. ADVARSEL Eksplosjonsfare ved feilaktig skifte av batteri. Benytt samme batteritype eller en tilsvarende type anbefalt av app

19、aratfabrikanten. Brukte batterier kasseres i henhold til fabrikantens instruksjoner. VARNING Explosionsfara vid felaktigt batteribyte. Anvnd samma batterityp eller en likvrdig typ somrekommenderas av apparattillverkaren. Kassera anvnt batteri enligt gllande freskrifter. VAROITUS Paristo voi rjht, jo

20、s se on virheellisesti asennettu. Vaihda paristo ainoastaan laitevalmistajan suosittelemaan tyyppiin. Hvit kytetty paristo valmistajan ohjeiden mukaisesti. ADVARSEL! Lithiumbatteri-Eksplosionsfare ved fejlagtig hndtering. Udskiftning m kun ske med batteri af samme fabrikat og type. Levr det brugte b

21、atteri tilbage til leverandren. CAUTION Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Discard used batteries according to the manufacturers instruc- tions. ATTENTION AU COMPOSANT AYANT RAPPORT LA SCURIT! LES COM

22、POSANTS IDENTIFS PAR UNE MARQUE 0 SUR LES DIAGRAMMES SCHMATIQUES ET LA LISTE DES PICES SONT CRITIQUES POUR LA SCURIT DE FONCTIONNEMENT. NE REMPLACER CES COMPOSANTS QUE PAR DES PISES SONY DONT LES NUMROS SONT DONNS DANS CE MANUEL OU DANS LES SUPPMENTS PUBLIS PAR SONY.3 MZ-E10 SECTION 1 SERVICING NOTE

23、 When repairing this device with the power on, if you remove the main board, this device stops working. In this case, you work without the device stopping by fastening the hook of the Open/Close detection switch (S803). Open/Close detection switch (S803)4 MZ-E10 SECTION 2 GENERAL This section is ext

24、racted from instruction manual. The Player 12 7 8 9 E C D 6 1 i (Headphones/earphones) jack 2 GROUP button 3 “3-color info-LED” 4 HOLD (Locking the control) switch 5 5-way control key ( . N* xVOL +, ) 6 OPEN switch 7 BUILT-IN BATTERY switch (at the bottom) 8 Terminals for charging stand (at the bott

25、om) 9 Hand strap hole Use the hole to attach your strap * N has a tactile dot . The display window of the remote control 12 34 56 7 9 1 Disc indication 2 Track number display 3 Character information display 4 Group play indication 5 Play mode indication 6 Virtual Surround/6-band equalizer indication

26、s 7 Battery level indication 8 Bookmark indication 9 Alarm indication The battery charging stand 1 2 1 DC IN (6V jack) (at the bottom) 2 Terminals for charging The headphones/earphones with a remote control 8 9 qa qs 7 q; A B C D 5 F 1 Headphones/earphones 2 Stereo mini plug 3 Control VOL +, Turn to

27、 adjust the volume . 4 x (stop) button 5 Jog lever (. u/ENT ) 6 (Group) +, button 7 Clip 8 HOLD switch 9 Display window q; DISPLAY button qa P MODE / (play mode/repeat) button qs SOUND button 8 To Pause Cue to the current track or the previous track Cue to the next track Go backwards or forward whil

28、e playing Searching for a specific position while viewing a elapsed time (Time search) Searching for a specific track while viewing track numbers or track names (Index search) Cue to the beginning of every 10th track (only during playback of the disc with no group settings 1) ) Remove the MD 1) For

29、more details, see “Using the group function.” 2) Once you open the lid, the point to start play will change to the beginning of the first track (except when the disc information has been stored in the personal disc memory). About the “3-color info-LED” The LED indicates the current operating mode, c

30、harging status, and battery condition. For details about the charging status, see “Getting started.” For details about the battery condition, see “When to recharge the built-in battery” on the back page. LED color Red Green Orange Do this (Beeps in the headphones/earphones) Press the jog lever (u) o

31、n the remote control (continuous short beeps). Press the jog lever (u) again to resume play. Slide the jog lever towards . on the remote control (three short beeps). (Press towards . on the player. ) Slide the jog lever towards on the remote control (two short beeps). (Press towards on the player.)

32、Slide and hold the jog lever towards . or on the remote control. (Press and hold towards . or on the player. ) While the player is paused, slide and hold the jog lever towards . or on the remote control. While the player is stopped, slide and hold the jog lever towards . or on the remote control. Pr

33、ess + or button. Press x, and then slide OPEN 2) . Playing an MD Insert an MD. 1 2 3 Play an MD. x N . VOL + VOL x VOL+ VOL 1 Press the jog lever ( u) on the remote control. (Press towards N on the player.) A short beep sounds in the headphones/earphones. The LED lights up. 2 Turn the control toward

34、s VOL + or on the remote control to adjust the volume. (Press towards VOL + or on the player. ) The volume indicator appears in the display, allowing you to check the volume level. To stop play, press x. A long beep sounds in the headphones/earphones. Playback starts from the point you last stopped

35、playing. To start playback from the beginning of the disc, press and hold the jog lever (u) for 2 seconds or more on the remote control (Press and hold towards N for 2 seconds or more on the player). 1 2 Insert an MD with the label side facing up, pushing the MD to the direction of the arrow in the

36、illustration. 1 Slide OPEN to open the lid. 2 Insert an MD. 3 Close the lid. “3-color info-LED” Jog lever (. u/ENT) 5-way control key Bottom side of the player Operating status Playing a disc with no group settings Playing a disc with group settings Cueing to the another group (Group Skip)5 MZ-E10 S

37、ECTION 3 DISASSEMBLY Note : Follow the disassembly procedure in the numerical order given. 3-1. PANEL ASSY (S), UPPER rThe equipment can be removed using the following procedure. 6 4 1 Two screws (M1.4) 7 Panel ASSY (S), upper 2 Claw Holder ASSY 3 Claw 5 Bracket ASSY Panel ASSY (S), upper Set Optica

38、l pick-up ASSY (ABX-1ES) Mechsnism deck (MT-MZE10-184) Bracket ASSY POWER board, MAIN board CONTROL board 3-2. MECHANISM DECK (MT-MZE10-184) 3 1 Screw, step 6 Mechanism deck(MT-MZE10-184) 4 OP flexible board(CN501) 2 Two claws 5 Motor flexible board(CN551)6 MZ-E10 3-3. BRACKET ASSY 3-4. POWER BOARD,

39、 MAIN BOARD 8 3 7 Two screws (M1.4) 1 Screw (M1.4) 4 Lid (DC), battery case 5 Konb (power) 9 Switch flexible board (CN801) 6 Screw (M1.4) 0 Bracket ASSY Sheet (blind) 2 Plate, retainer 6 1 Case, battery 3 Battery, lithium ion storage 2 Retainer, battery 4 POWER board 5 Power relay flexible board(CN9

40、52, CN953) 7 MAIN board ASSY7 MZ-E10 3-5. CONTROL BOARD 7 CONTROL board Bracket ASSY 6 Button (control) 4 Cover (control) 3 Knob (open) 1 Screw (M1.4) 2 Remove three claws 5 Switch flexible board(CN801) 3-6. OPTICAL PICK-UP ASSY (ABX-1ES) 5 2 Gear (SA) Mechanism deck (MT-MZE10-184) 1 Washer (0.8-2.5

41、) 4 Spring, thrust detent 3 Screw, tapping 6 Optical pick-up ASSY(ABX-1ES)MZ-E10 8 SECTION 4 TEST MODE Remote control LCD Press and hold down to hold the current display while the key is being pressed. 4-2-3. How to release the TEST MODE When method 1 was used: Turn off the power and open the solder

42、 bridge on TAP602 on the main board. Note: The solder should be removed clean. The remaining solder may make a short with the chassis and other part. When method 2 was used: Turn off the power. Note: If electrical adjustment (see page 11) has not been finished completely, always start in the test mo

43、de. 4-3. TEST MODE STRUCTURE 4-1. GENERAL When entered in the TEST MODE, this set provides the Overall Adjustment mode which allows CD and MO discs to be auto- matically adjusted. In the Overall Adjustment mode, the system discriminates between CD and MO discs, performs adjustments in sequence autom

44、atically, and displays the faulty location if any fault is found. In the Manual mode, selected adjustments can be performed automatically. The attached remote control is used to operate the TEST MODE. Unless otherwise specified in the text, the key means that on the remote control. 4-2. SETTING THE

45、TEST MODE 4-2-1. How to set the TEST MODE To set the TEST MODE, two methods are available. 1 Solder bridge and short TAP602 (TEST) on the main board. Then turn on the power. MAIN BOARD (SIDE A) 2 In the normal mode, operate the keys on the set and those on the remote control as specified below: Turn

46、 on HOLD switch on the set. Holding down x(STOP) key on the set, press the keys on the remote control in the following sequence:t t .t .t t .t t .t t 4-2-2. Operations when the TEST MODE is set When the TEST MODE is entered, the system switches to the dis- play check mode within the TEST MODE. From this mode, the other Test modes can be accessed. When the TEST MODE is set, the LCD repeats a cycle of the fol- lowing displays: 001 V1.000 All on All off Microprocessor version display