Kenwood-RXDM57MP-cs-sm 维修电路原理图.pdf
《Kenwood-RXDM57MP-cs-sm 维修电路原理图.pdf》由会员分享,可在线阅读,更多相关《Kenwood-RXDM57MP-cs-sm 维修电路原理图.pdf(22页珍藏版)》请在收音机爱好者资料库上搜索。
1、COMPACT Hi-Fi COMPONENT SYSTEMRXD-M57MP-H/M57MP-SSERVICE MANUAL(HM-537MP) 2004-8 PRINTED IN KOREAB51-5923-00 (K/K) 339In compliance with Federal Regulations, following are repro-duction of labels on, or inside the product relating to laserproduct safety.KENWOOD Corp. certifies this equipment conform
2、s to DHHSRegulations No.21 CFR 1040. 10, Chapter 1, subchapter J.DANGER : Laser radiation when open and interlock defeated. AVOID DIRECT EXPOSURE TO BEAM.Caution : No connection of ground line if disassemble the unit. Please connect the ground line on rear panel, PCBs, Chassis and some others.70%Fro
3、nt cabinet assy *(A60-)Knob(Open/Close)(K29-8416-08)Knob(EQ/Bass) *(K29-)Knob(Volume)(K29-8413-08)Control panel *(A21-)Knob(Demo) *(K29-)Knob(Prog) *(K29-)CD Door *(A29-)Knob(Power)(K29-8417-08)Knob(Function)(K29-8414-08)Knob(Stop/REC)(K29-8415-08)Cass lid assy *(A53-)Rubber foot(G11-2961-08)Knob(Pl
4、ay) *(K29-)Phone jack(E11-0981-08)* Refer to parts list on page 20.RadioFans.CN 收音机爱 好者资料库Remote control unit (1)(A70-1688-08)AM loop antenna (1)(T90-0908-08)FM ANT Wire (1)(T90-0918-08)Batteries (R6/AA) (2)AC plug adapter (1)(E03-0115-05)Use to adapt the plug on the power cord to the shape of the w
5、all outlet.(Accessory only for regions where use is necessary.)RXD-M57MP2CONTENTS / ACCESSORIES / CAUTIONSCONTENTS / ACCESSORIES / CAUTIONS.2EXTERNAL VIEW.3ADJUSTMENT.4PC BOARD .8SCHEMATIC DIAGRAM .13EXPLODED VIEW .19PARTS LIST.20SPECIFICATIONS.BACK COVERCONTENTSACCESSORIESSYSTEM CONFIGURATIONCLASS
6、1 LASER PRODUCTLASER KLASSE 1APPAREIL A LASER DE CLASSE 1LUOKAN 1 LASERLAITEKLASS 1 LASERAPPARATThe marking this product has been classified as Class 1. It means that there is no danger of hazardous radiation outside the product.Location: BottomResetting the MicrocomputerThe microcomputer may malfun
7、ction (unit can-not be operated, or shows an erroneous dis-play) if the power cord is unplugged while thepower is ON, or due to some other externalfactor. If this happens, execute the followingprocedure to reset the microcomputer andreturn the unit to its normal operating condition.Plug in the AC po
8、wer cord to the wall outlet,and within 5 seconds, press and hold downthe 7button and press CD button. Please note that resetting the microcomputerwill clear the contents of the memory andreturn the unit to the state it was in when itleft the factory.CAUTIONSSYSTEMRECEIVERSPEAKERSHM-537MP-HRXD-M57MP-
9、HLS-M57-HHM-537MP-SRXD-M57MP-SLS-M57-SRadioFans.CN 收音机爱 好者资料库RXD-M57MP3EXTERNAL VIEW220-240V110-120VVOLTAGESELECTORTop cabinet(A01-3943-08)FM 75 ohm Ant.(E70-0200-08)Rear cabinet(A80-4494-08)Voltage SW. *(S62-0124-08)* Refer to parts list on page 20.RXD-M57MP4ADJUSTMENTSERVICE ADJUSTMENT Lubrication
10、 The mechanical parts are factory coated with a thin coat of light grease and should not require further lubrication. If a light grease is applied, be careful not to get any grease on the play/record head or erase head, hubs, pulleys, tapes reels, drive belts, or switches. Use a good lubricant such
11、as Silicon Lube G322L or Lubricate.Service Check Before aligning the mechanism, wipe off any accumulated dirt with denatured alcohol. Wipe around parts where the tape contacts and around all rotating parts. Drive belts are specially processed. Do not clean them with alcohol. Mechanical Torque Use a
12、cassette type torque gauge and check the tape mechanism. Take-up torque 35 to 70 g-cm Rewind torque 50 g-cm min. Fast forward torque 50 g-cm min. Pinch Wheel Pressure No adjustment to the pinch roller spring is necessary. It should be sufficient to give at least 40 g-cm pull force. Tape Head Servici
13、ng Each time the unit is serviced, the face of all heads should be thoroughly cleaned with denatured alcohol or commercial head cleaning solution. The playback head should be demagnetized with a commercial demagnetizer. Accumulation of tape oxide during normal operations can cause problems, includin
14、g loss of high frequencies and wow and flutter. Erase Head The erase head is properly aligned when the tape rides directly between the tape guide on the head without crinkling the tape. Play/Record and Playback Head Azimuth Adjustment To adjust the play/record and playback head azimuth screw: 1. Con
15、nect two (2) VTVMs and a dual trace scope to the stereo headphone jack (as shown) with a 32 ohm dummy load. (See Figure 1.) VTVMVTVMDUMMY LOAD JK400SCOPECH1CH2 Figure 1. Azimuth Adjustment RXD-M57MP5ADJUSTMENT 2. Insert a 10 kHz test tape (Teac MTT-1141V or Equivalent) into the tape mechanism and pl
16、ay it back. 3. While playing back the test tape, slowly turn the azimuth adjusting screw until the amplitude of both channel output waveforms is maximum and in phase. Note: Reiteration adjusting Right, lift the screw, until the amplitude of both channel output waveform is maximum. (See Figure 2.) 4.
17、 Secure the azimuth screw in place with glue or paint after making the adjustment. Figure 2. Head Output Signal Tape Speed Adjustment 1. Set the function switch to TAPE. 2. Connect a frequency counter with a 32 ohm dummy load to the stereo headphone jack. (See Figure 3.) FREQUENCY COUNTERDUMMY LOADJ
18、K400 Figure 3. Tape Speed Adjustment 3. Insert and play back a 3 kHz test tape (Teac MTT-111 or Equivalent) into the tape mechanism. 4. Insert an insulated alignment tool and adjust the tape speed potentiometer (MOTOR) until the frequency counter indicates 2940 Hz to 3090 Hz. Bias Oscillator Frequen
19、cy and Level Adjustment 1. Set the function switch to TAPE and the record and play tape mechanism to RECORD. 2. Connect a VTVM and frequency counter to test point R/P HEAD. 3. Adjust bias oscillator coil L203 until the frequency counter indicates 67 kHz 0.5 kHz. RXD-M57MP6ADJUSTMENTTUNER ALIGNMENT P
20、ROCEDURE Equipment needed: 1. AM Signal generator 2. FM Signal generator 3. DC Voltage meter 4. Oscilloscope 5. Output meter (VTVM) AM Alignment Step S/G Frequency Dial SettingIndicator Adjust Remarks 1 450 kHz (1 kHz 30% mod.) 612 kHz Connect oscilloscope or VTVM to speaker jack T101 Adjust for max
21、imum output 2 531 kHz (1 kHz 30% mod.) Low end Connect DC voltage meter to test point Vt and ground L102 Adjust until Vt equal to 1.5 0.05V 3 1602 kHz (1 kHz 30% mod.) High end Same as step 2 Confirm Vt: 6.58.5V 4 612 kHz (1 kHz 30% mod.) 612 kHz Same as step 1 L103 Maximum output 5 1404 kHz (1 kHz
22、30% mod.) 1404 kHz Same as step 1 TC101 Maximum output 6 Repeat steps 4 and 5 to minimize tracking error 7 999 kHz (1 kHz 30%mod.) 999 kHz Same as step 1 Offset is less than 6 dB. 60 cmAM SIGNAL GENERATORAM LOOP ANTAM LOOPANTENNADUMMY LOADVTVMTEST UNITFigure 4. AM IF/RF Tracking RXD-M57MP7ADJUSTMENT
23、FM Alignment: TEST UNIT Figure 5. FM Band Frequency Coverage Alignment Connect FM S/G to ANT inputs (mod 1 kHz 22.5kHz dev.) Step S/G Frequency Dial Setting Indicator Adjust Remarks 1 87.5 MHz Low end Connec t DC Voltage meter to test point Vt and ground Confirm Vt: 1.7 0.2V 2 108 MHz High end Same
24、as step 1 Confirm Vt: 8.5 1V Figure 6. FM Band/Tracking FM GENERATORDUMMYANTENNATP1TEST UNITDUMMYLOADVTVMOSCILLOSCOPEVtGROUND DC8ACEBD2135746Refer to the schematic diagram for the value of resistors and capacitors.PC BOARD (Component side view)CN501SW511KEYHEADPHONESW510SW509SW516SW506SW512SW503SW19
25、SW515SW505SW514SW513SW500SW502SW504SW517SW507SW501SW508LED500IC501CN1CN3JACK2CN4JK400PHONESCN403OPEN/CLOSETIMERSETTIMERON/OFFPRE/ALBUMUPPRE/ALBUMDOWNEQ/1158X-BASSDEMOPROGRAMRECPLAY/PAUSECDTAPE/MODETUNER BANDSTANDBY31DIRECTIONF-SKIP UPF-SKIP DOWNSTOPVOLUMER513R514R515R516R500R521R520R519R517R518R524R
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- Kenwood-RXDM57MP-cs-sm 维修电路原理图 Kenwood RXDM57MP cs sm 维修 电路 原理图