JVC-MXK350V-cs-sm 维修电路原理图.pdf

《JVC-MXK350V-cs-sm 维修电路原理图.pdf》由会员分享，可在线阅读，更多相关《JVC-MXK350V-cs-sm 维修电路原理图.pdf（80页珍藏版）》请在收音机爱好者资料库上搜索。

1、MX-K350VSERVICE MANUALCOMPACT COMPONENT SYSTEMMX-K350V Area SuffixUS . SINGAPOREUX . SAUDIContentsSafety precautions - 1- 2Important for laser products - 1- 3Preventing static electricity- 1- 4Disassembly method - 1- 5Adjustment method - 1-18Flow of functional operation until TOC read - 1-20Maintena

2、nce of laser pickup - 1-21Replacement of laser pickup- 1-21Description of major ICs - 1-22COPYRIGHT 2001VICTOR COMPANY OF JAPAN, LTD. No.21166 Dec.2002RadioFans.CN 收音机爱 好者资料库1-21. This design of this product contains special hardware and many circuits and components specially orsafety purposes. For

3、continued protection, no changes should be made to the original design unlessauthorized in writing by the manufacturer. Replacement parts must be identical to those used in the originalcircuits. Services should be performed by qualified personnel only.2. Alterations of the design or circuitry of the

4、 product should not be made. Any design alterations of theproduct should not be made. Any design alterations or additions will void the manufacturers warranty andwill further relieve the manufacture of responsibility for personal injury or property damage resulting therefrom.3. Many electrical and m

5、echanical parts in the products have special safety-related characteristics. Thesecharacteristics are often not evident from visual inspection nor can the protection afforded by themnecessarily be obtained by using replacement components rated for higher voltage, wattage, etc.Replacement parts which

6、 have these special safety characteristics are identified in the Parts List of ServiceManual. Electrical components having such features are identified by shading on the schematics and by( ! ) on the Parts List in the Service Manual. The use of a substitute replacement which does not have thesame sa

7、fety characteristics as the recommended replacement parts shown in the Parts List of ServiceManual may create shock, fire, or other hazards.4. The leads in the products are routed and dressed with ties, clamps, tubings, barriers and the like to beseparated from live parts, high temperature parts, mo

8、ving parts and/or sharp edges for the preventionof electric shock and fire hazard. When service is required, the original lead routing and dress shouldbe observed, and it should be confirmed that they have been returned to normal, after re-assembling.5. Leakage currnet check (Electrical shock hazard

9、 testing) After re-assembling the product, always perform an isolation check on the exposed metal parts of theproduct (antenna terminals, knobs, metal cabinet, screw heads, headphone jack, control shafts, etc.) tobe sure the product is safe to operate without danger of electrical shock. Do not use a

10、 line isolationtransformer during this check.?Plug the AC line cord directly into the AC outlet. Using a “ Leakage Current Tester ” , measure theleakage current from each exposed metal parts of the cabinet, particularly any exposed metal parthaving a return path to the chassis, to a known good earth

11、 ground. Any leakage current must notexceed 0.5mA AC (r.m.s.)?Alternate check method Plug the AC line cord directly into the AC outlet. Use an AC voltmeter having, 1,000 ohms per voltor more sensitivity in the following manner. Connecta 1,500 10W resistor paralleled by a 0.15 FAC-type capacitor betw

12、een an exposed metalpart and a known good earth ground. Measure theAC voltage across the resistor with the ACvoltmeter.Move the resistor connection to each exposed metalpart, particularly any exposed metal part having areturn path to the chassis, and meausre the ACvoltage across the resistor. Now, r

13、everse the plug inthe AC outlet and repeat each measurement. Voltagemeasured Any must not exceed 0.75 V AC (r.m.s.).This corresponds to 0.5 mA AC (r.m.s.).In regard with component parts appearing on the silk-screen printed side (parts side) of the PWB diagrams, theparts that are printed over with bl

14、ack such as the resistor ( ), diode ( ) and ICP ( ) or identified by the“! ” mark nearby are critical for safety.When replacing them, be sure to use the parts of the same type and rating as specified by the manufacturer.(Except the J and C version) Safety Precautions ! CAUTIONBurrs formed during mol

15、ding maybe left over on some parts of thechassis. Therefore, pay attentionto such burrs in the case ofpreforming repair of this system. Warning1. This equipment has been designed and manufactured to meet international safety standards.2. It is the legal responsibility of the repairer to ensure that

16、these safety standards are maintained.3. Repairs must be made in accordance with the relevant safety standards.4. It is essential that safety critical components are replaced by approved parts.5. If mains voltage selector is provided, check setting for local voltage.RadioFans.CN 收音机爱 好者资料库1-3Importa

17、nt for laser products1. CLASS 1 LASER PRODUCT2. DANGER : Invisible laser radiation when open and interlock failed or defeated. Avoid direct exposure to beam.3. CAUTION : There are no serviceable parts inside the LaserUnit. Do not disassemble the Laser Unit. Replace thecomplete Laser Unit if it malfu

18、nctions.4. CAUTION : The compact disc player uses invisible laserradiation and is equipped with safety switches whichprevent emission of radiation when the drawer is openand the safety interlocks have failed or are defeated. It isdangerous to defeat the safety switches.5. CAUTION : If safety switche

19、s malfunction, the laser is ableto function.6. CAUTION : Use of controls, adjustments or performance ofprocedures other than those specified herein may resultin hazardous radiation exposure. ! CAUTIONPlease use enough caution not tosee the beam directly or touch it incase of an adjustment or operati

20、oncheck.VARNING : Osynlig laserstrlning r denna del rppnad och sprren r urkopplad. Betraktaej strlen.VARO : Avattaessa ja suojalukitus ohitettaessa oletalttiina nkymttmlle lasersteilylle. lkatso steeseen.ADVARSEL : Usynlig laserstrling ved bning, nrsikkerhedsafbrydere er ude af funktion.Undg udsttel

21、se for strling.ADVARSEL : Usynlig laserstrling ved pning, nrsikkerhetsbryteren er avslott. Unngutsettelse for strling. REPRODUCTION AND POSITION OF LABELSWARNING LABEL1-4Preventing static electricity1. Grounding to prevent damage by static electricityElectrostatic discharge (ESD), which occurs when

22、static electricity stored in the body, fabric, etc. isdischarged, can destroy the laser diode in the traverse unit (optical pickup). Take care to prevent thiswhen performing repairs.2. About the earth processing for the destruction prevention by static electricityIn the equipment which uses optical

23、pick-up (laser diode), optical pick-up is destroyed by the staticelectricity of the work environment.Be careful to use proper grounding in the area where repairs are being performed.2-1 Ground the workbenchGround the workbench by laying conductive material (such as a conductive sheet) or an iron pla

24、teover it before placing the traverse unit (optical pickup) on it.2-2 Ground yourselfUse an anti-static wrist strap to release any static electricity built up in your body.3. Handling the optical pickup1. In order to maintain quality during transport and before installation, both sides of the laser

25、diode on thereplacement optical pickup are shorted. After replacement, return the shorted parts to their original condition.(Refer to the text.)2. Do not use a tester to check the condition of the laser diode in the optical pickup. The testers internal powersource can easily destroy the laser diode.

26、4. Handling the CD changer unit (optical pickup)1. Do not subject the CD changer unit (optical pickup) to strong shocks, as it is a sensitive, complex unit.2. Cut off the shorted part of the flexible cable using nippers, etc. after replacing the optical pickup. For specificdetails, refer to the repl

27、acement procedure in the text.Remove the anti-static pin when replacing the CD changerunit. Be careful not to take too long a time when attaching itto the connector.3. Handle the flexible cable carefully as it may break whensubjected to strong force.4. It is not possible to adjust the semi-fixed res

28、istor that ad-justs the laser power. Do not turn it.Attention when traverse unit is decomposed* Please refer to “Disassembly method ” in the text for pickup and how to detach the CD changer mechanism.1. Remove the CD changer unit.2. Disconnect the harness from connector on the CD motor board.3. Sold

29、er is put up before the card wire is removed from connectorCn601on the main board as shown in Fig.1 and Fig. 2. (When the wire is removed without putting up solder, the CDpick-up assembly might destroy.)4. Please remove solder after connecting the card wire with CN601when you install picking up in t

30、he substrate.1-5Disassembly methodCommence disassembly of this set by removing the main units and then proceed to the components and assembliesinside the units. Replacement of the fuses and the power IC? Top cover? CD changer unit? Front panel assembly? Chassis unit? CD changer unit? Removing the ma

31、in PCB? Removing the CD changer mechanism assembly? Removing the CD pickup? Replacing the loading motor and belt of the CD changer tray? Replacing the CD tray rotor belt of CD changer, and removing the motor? Front panel assembly? Removing the cassette deck mechanism? Removing the earphone jack PCB?

32、 Removing the control/FL PCB? Removing the switch PCB and ACTIVE BASS EX. switch PCB? Removing the cassette deck main motor, and replacing the main belts? Removing the leaf switches of the cassette deck mechanism? Removing the cassette deck heads? Chassis unit? Removing the 3-pin regulator? Removing

33、 the power amp and supply PCB and the Power Trans PCB? Removing the sub power PCB1-6Replacement of the fuses and the power IC? Replacing the fuses (See Fig.1, Fig.3) ? Prior to performing the following procedure, removethe left side BOARD and remove tuner PCB (Fig.3,BB)1. Replace the fuses inside.Ca

34、ution Be sure to use fuses with the specified ratings.? Replacing the power IC (See Fig.2 ) ? Prior to performing the following procedure, removethe top cover.1. Remove the two screws “ A ” from the heat sinkbetweenthe power IC.2. Remove the solder fixing the power IC.? Replacing the heat sink cover

35、1. Remove the six screws from the back panel.2. Pull the heat sink cover outward.1-7? Removing the top cover and two sidesBOARD (See Fig.4 and 5)1. Remove the six screws “B ” that retain the top coverfrom the rear of the body.2. Remove the eight screws “ C ” and “ D ” that retain thetop from the two

36、 sides of the body.3. Remove the top cover from the body by lifting it towardthe rear.1-8? Removing the CD changer unit (See Fig.6 and 9)? ? Prior to performing the following procedures, removethe top cover and both sides BOARD.Caution Although the CD mechanism unit can beremoved without removing th

37、e CD traypanel, it is still recommended to remove itin order to prevent damage.a. From the front panel side of this set, push in the sectionsmarked with arrows and pull out the CD tray towardthe front.b. Remove the CD tray panel by pushing both of itsextremities upward in the direction of the arrows

38、.c. Push the CD tray deep into the set.1. Disconnect the card wires from the CD PCB CN704,CN607, CN1101 and disconnect CN1 (shield wire) fromback panel.2. From the rear of the set, remove the two screws “ E ”and two serews “ G ” on the front panel left and rightside.3. Handle the CD changer unit rea

39、r, take out unit.Fig.61-9? Removing the front panel assembly (See Fig.10 and 11)? ? Prior to performing the following procedures, removethe top cover and both sides board.? Also remove the CD changer unit.1. Disconnect the parallel wire and card wire from theconnectors CN702, CN701, CN703, CN850 on

40、thepower amp and supply PCB.2. Remove the two screws “ H ” retaining the front panelassembly onto the bottom of the body.3. Remove the screw “ I ” retaining the cassette deckmechanism and then remove then GND lug “ b ” thatcomes from the power amp and supply PCB.4. Disengage the claws “ c ” on both

41、sides at the bottomof the front panel assembly and then remove theassembly.1-10? Removing the CD PCB(See Fig.12 and 13)? ? Prior to performing the following procedures, removethe top cover and both sides board.? Also remove the CD changer unit.1. The two screws “ E ” that retain the VCD assemblyshou

42、ld be removed.2. Disconnect the wires from CN602, CN603, CN604and CN605 on the CD PCB, which is located on theback side of the CD changer unit.3. The two screws “ J ” that retain the CD PCB should beremoved.4. Remove the CD PCB by pulling it toward the side wherethe CN601 is located.5. Using solder,

43、 short the CD pickup to connect to shortround.Caution After re-connecting the wires, be sure toremove the shorting solder from the GND con-nection.6. Disconnect the card wire from the connector CN601on the main PCB and then remove the main PCB.1-11? Removing the CD changer mechanismassembly (See Fig

44、.14 and 16)? ? Prior to performing the following procedures, removethe top cover and both sides board.? Also remove the CD changer unit.1. Remove the screws “ d ” from the front chuch base ofthe CD changer mechanism unit.2. Turn the CD changer mechanism cover base and removethe screws “ e ” connecti

45、ng the unit to the CD changermechanism assembly.3. Removing the four screws “ k ” retaining the CDmechanism holder assembly.Caution When replacing the CD changer mechanismassembly, be sure not to mistake thepositions of the silver color and copper colorspring.1-12? Removing the CD PCB (See Fig.17)?

46、? Prior to performing the following procedures, removethe top cover and both sides board.? Also remove the CD changer unit.? Also remove the CD changer mechanism.1. Widen the section “ f ” .2. While keeping the section “ f ” wide open, push thesection “ g ” in the direction of the arrow to remove th

47、eshaft, and then remove the CD pickup.? Replacing the loading motor and rotor beltof the CD changer (See Fig.18)? Prior to performing the following procedure, removethe top cover.? Also open the CD changer tray.1. Remove the two screws “L ” retaining the CD changertray loading motor.2. Remove the tw

48、o screws “M ” retaining the gear plateand take it out, after remove the rotor belt from thepulley.? Replacing the CD turn table and removingthe motor (See Fig. 19 and 20)? ? Prior to performing the following procedures, removethe top cover.? Also remove the CD changer unit.1. Remove the one screws “

49、 N ” retaining the CD (Turntable).2. Remove the two screws “ O ” retaining the stopperbrackets on both sides of the CD changer unit.3. Remove the stopper brackets from both sides of theCD changer unit.4. Pull out the CD tray from the CD changer unit, all theway and lift the tray (u/ ward) to remove.

50、5. Remove the gear and after push out the tray motorlocker and pull out the tray motor from the CD tray.1-13? Removing the cassette deck mechanism (See Fig.21)? Prior to performing the following procedure, removethe top cover and both sides board.? Also remove the CD changer unit.? Also remove the f