JVC-MXG700R-cs-sm 维修电路原理图.pdf

《JVC-MXG700R-cs-sm 维修电路原理图.pdf》由会员分享，可在线阅读，更多相关《JVC-MXG700R-cs-sm 维修电路原理图.pdf（44页珍藏版）》请在收音机爱好者资料库上搜索。

1、SERVICE MANUALCOMPACT COMPONENT SYSTEMNo.21103May. 2002COPYRIGHT 2002 VICTOR COMPANY OF JAPAN, LTD.MX-G700RMX-G700RContentsSafety PrecautionsImportant for laser produbtsPreventing static electricityDisassembly method Wiring connectionAdjustment methodFlow of functional operation until TOC readMainte

2、nance of laser pickupReplacement of laser pickupTrouble shootingDescription of major ICs1-21-41-51-61-191-201-241-251-251-261-2942Area suffixB - U.K.E - Continental EuropeEN - Northern EuropeEV - Eastern EuropeSP-MXGT700SP-MXGT700DISC CHANGESTANDBY/ONSTANDBYCD-R/RW PLAYBACKTUNINGCLOCK/TIMERDISPLAYPH

3、ONESREPEATREC START/ STOPCD REC STARTDUBBINGPROGRAMRANDOMTAPE BTAPE AAUXTAPECDFM / AMSUBWOOFERLEVELSOUNDMODEMX-G700 RCD 2CD 3EXTENDED SUPER BASSCD3FULL - LOGIC CONTROLCD SYNCHRO RECORDINGCD 1ECODISPLAY MODEPTY/EON SELECT +CA-MXG700RDISCSKIPVOLUM EVOLUM E+RM SMXG500 R REMOTE CONTROLSTANDBY/ON12345678

4、910+10SLEEPSOUNDMODETAPE A/BFADE M UTINGDISPLAY MODE SELECT +FM /A MAUXCD TAPE SUBWOOFERLEVELFM MODEPTY/ EONRadioFans.CN 收音机爱 好者资料库MX-G700R1-21. This design of this product contains special hardware and many circuits and components specially for safety purposes. For continued protection, no changes

5、should be made to the original design unless authorized in writing by the manufacturer. Replacement parts must be identical to those used in the original circuits. Services should be performed by qualified personnel only.2. Alterations of the design or circuitry of the product should not be made. An

6、y design alterations of the product should not be made. Any design alterations or additions will void the manufacturers warranty and will further relieve the manufacture of responsibility for personal injury or property damage resulting therefrom.3. Many electrical and mechanical parts in the produc

7、ts have special safety-related characteristics. These characteristics are often not evident from visual inspection nor can the protection afforded by them necessarily be obtained by using replacement components rated for higher voltage, wattage, etc. Replacement parts which have these special safety

8、 characteristics are identified in the Parts List of Service Manual. Electrical components having such features are identified by shading on the schematics and by ( ) on the Parts List in the Service Manual. The use of a substitute replacement which does not have the same safety characteristics as t

9、he recommended replacement parts shown in the Parts List of Service Manual may create shock, fire, or other hazards.4. The leads in the products are routed and dressed with ties, clamps, tubings, barriers and the like to be separated from live parts, high temperature parts, moving parts and/or sharp

10、 edges for the prevention of electric shock and fire hazard. When service is required, the original lead routing and dress should be observed, and it should be confirmed that they have been returned to normal, after re-assembling.5. Leakage currnet check (Electrical shock hazard testing)After re-ass

11、embling the product, always perform an isolation check on the exposed metal parts of the product (antenna terminals, knobs, metal cabinet, screw heads, headphone jack, control shafts, etc.) to be sure the product is safe to operate without danger of electrical shock.Do not use a line isolation trans

12、former during this check.Plug the AC line cord directly into the AC outlet. Using a Leakage Current Tester, measure the leakage current from each exposed metal parts of the cabinet, particularly any exposed metal part having a return path to the chassis, to a known good earth ground. Any leakage cur

13、rent must not exceed 0.5mA AC (r.m.s.).Alternate check methodPlug the AC line cord directly into the AC outlet. Use an AC voltmeter having, 1,000 ohms per volt or more sensitivity in the following manner. Connect a 1,500 10W resistor paralleled by a 0.15 F AC-type capacitor between an exposed metal

14、part and a known good earth ground.Measure the AC voltage across the resistor with the AC voltmeter. Move the resistor connection to each exposed metal part, particularly any exposed metal part having a return path to the chassis, and meausre the AC voltage across the resistor. Now, reverse the plug

15、 in the AC outlet and repeat each measurement. Voltage measured any must not exceed 0.75 V AC (r.m.s.). This corresponds to 0.5 mA AC (r.m.s.). 1. This equipment has been designed and manufactured to meet international safety standards.2. It is the legal responsibility of the repairer to ensure that

16、 these safety standards are maintained.3. Repairs must be made in accordance with the relevant safety standards.4. It is essential that safety critical components are replaced by approved parts.5. If mains voltage selector is provided, check setting for local voltage.Good earth groundPlace this prob

17、e on each exposedmetal part.AC VOLTMETER(Having 1000 ohms/volts,or more sensitivity)1500 10W0.15 F AC TYPE!Burrs formed during molding may be left over on some parts of the chassis. Therefore, pay attention to such burrs in the case of preforming repair of this system.In regard with component parts

18、appearing on the silk-screen printed side (parts side) of the PWB diagrams, the parts that are printed over with black such as the resistor ( ), diode ( ) and ICP ( ) or identified by the mark nearby are critical for safety. (This regulation does not correspond to J and C version.)RadioFans.CN 收音机爱

19、好者资料库1-3MX-G700R1. Service should be performed by qualified personnel only.2. This equipment has been designed and manufactured to meet international safety standards.3. It is the legal responsibility of the repairer to ensure that these safety standards are maintained.4. Repairs must be made in acc

20、ordance with the relevant safety standards.5. It is essential that safety critical components are replaced by approved parts.6. If mains voltage selector is provided, check setting for local voltage.1. This design of this product contains special hardware and many circuits and components specially f

21、or safety purposes. For continued protection, no changes should be made to the original design unless authorized in writing by the manufacturer. Replacement parts must be identical to those used in the original circuits. 2. Any unauthorised design alterations or additions will void the manufacturers

22、 guarantee ; furthermore the manufacturer cannot accept responsibility for personal injury or property damage resulting therefrom.3. Essential safety critical components are identified by ( ) on the Parts List and by shading on the schematics, and must never be replaced by parts other than those lis

23、ted in the manual. Please note however that many electrical and mechanical parts in the product have special safety related characteristics. These characteristics are often not evident from visual inspection. Parts other than specified by the manufacturer may not have the same safety characteristics

24、 as the recommended replacement parts shown in the Parts List of the Service Manual and may create shock, fire, or other hazards.4. The leads in the products are routed and dressed with ties, clamps, tubings, barriers and the like to be separated from live parts, high temperature parts, moving parts

25、 and/or sharp edges for the prevention of electric shock and fire hazard. When service is required, the original lead routing and dress should be observed, and it should be confirmed that they have been returned to normal, after re-assembling.!Burrs formed during molding may be left over on some par

26、ts of the chassis. Therefore, pay attention to such burrs in the case of preforming repair of this system.(U.K only)MX-G700R1-4Important for laser products1.CLASS 1 LASER PRODUCT2.DANGER : Invisible laser radiation when open and inter lock failed or defeated. Avoid direct exposure to beam.3.CAUTION

27、: There are no serviceable parts inside theLaser Unit. Do not disassemble the Laser Unit. Replace the complete Laser Unit if it malfunctions.4.CAUTION : The compact disc player uses invisible laserradiation and is equipped with safety switches whichprevent emission of radiation when the drawer is op

28、en and the safety interlocks have failed or are de feated. It is dangerous to defeat the safety switches.5.CAUTION : If safety switches malfunction, the laser is able to function.6.CAUTION : Use of controls, adjustments or performance of procedures other than those specified herein may result in haz

29、ardous radiation exposure.REPRODUCTION AND POSITION OF LABELSWARNING LABEL!CAUTIONPlease use enough caution not to see the beam directly or touch it in case of an adjustment or operationcheck.CLASS 1LASER PRODUCT1-5MX-G700RPreventing static electricity1. Grounding to prevent damage by static electri

30、city Electrostatic discharge (ESD), which occurs when static electricity stored in the body, fabric, etc. is discharged, can destroy the laser diode in the traverse unit (optical pickup). Take care to prevent this when performing repairs.2. About the earth processing for the destruction prevention b

31、y static electricity In the equipment which uses optical pick-up (laser diode), optical pick-up is destroyed by the static electricity of the work environment.Be careful to use proper grounding in the area where repairs are being performed. 2-1 Ground the workbench Ground the workbench by laying con

32、ductive material (such as a conductive sheet) or an iron plate over it before placing the traverse unit (optical pickup) on it.2-2 Ground yourself Use an anti-static wrist strap to release any static electricity built up in your body. 3. Handling the optical pickup1. In order to maintain quality dur

33、ing transport and before installation, both sides of the laser diode on the replacement optical pickup are shorted. After replacement, return the shorted parts to their original condition. (Refer to the text.)2. Do not use a tester to check the condition of the laser diode in the optical pickup. The

34、 testers internal power source can easily destroy the laser diode. 4. Handling the traverse unit (optical pickup)1. Do not subject the traverse unit (optical pickup) to strong shocks, as it is a sensitive, complex unit. 2. Cut off the shorted part of the flexible cable using nippers, etc. after repl

35、acing the optical pickup. For specific details, refer to the replacement procedure in the text. Remove the anti-static pin when replacing the traverse unit. Be careful not to take too long a time when attaching it to the connector. 3. Handle the flexible cable carefully as it may break when subjecte

36、d to strong force. 4. It is not possible to adjust the semi-fixed resistor that adjusts the laser power. Do not turn itConductive material (conductive sheet) or iron plate(caption)Anti-static wrist strapAttention when CD mechanism assembly is decomposed1. Remove the CD changer unit. 2. Remove the CD

37、 changer mechanism. 3. Solder is put up before the card wire is removed from the pickup unit connector on the CD mechanism assembly. (When the card wire is removed without putting up solder, the CD pick-up assembly might destroy.) 4. Please remove solder after connecting the card wire with the picku

38、p unit connector when you install picking up in the substrate.*Please refer to Disassembly method in the text for pick-up and how to detach the CD mechanism assembly. SolderingFig.1Fig.2Card wireCard wirePicup unitconnectorPicup unitconnectorCD changer unitCD changer mechanismMX-G700R1-6Remove the t

39、hree screws A attaching the metal cover on the back of the body. Remove the six screws B attaching the metal cover on the both sides of the body.Remove the metal cover from the body by lifting the rear part of the cover.1.2.3.Disassembly methodRemoving the metal cover (See Fig.1) ONE POINT How to ej

40、ect the CD tray (see fig.2)Although it will end if the OPEN/CLOSE button is pushed when a power supply can be taken, when that is not right, CD tray will be opened manually.Turn the loading pulley gear at the bottom of the CD changer unit as shown in Fig.2 and draw the CD tray toward the front. Remo

41、ving the CD tray fitting (See Fig. 3)Prior to performing the following procedure, eject the CD tray.After drawing the lower part of the CD tray fitting toward the front, remove the five claws. Then, while moving the CD tray fitting upward, remove it.1.Prior to performing the following procedure, rem

42、ove the metal cover and CD tray fitting.Remove the card wire attached to CD changer unit on the adhesion tape.Disconnect the card wire from the connector CW105 on the CD board.Disconnect the harness from the connector RCW6 on the main board and CW107 on the CD board.Remove the two screws C attaching

43、 the CD changer unit to the rear panel.Remove the two screws D attaching the CD changer unit to the both sides of front panel assembly.Draw the CD changer unit upward from behind while pulling the rear panel outward. 1.2.3.4.5.6.Removing the CD changer unit (See Fig.4 to 7)Fig.1Fig.2Fig.3Metal cover

44、AB(both sides)Joint ClawCD tray fitting Loading pulley gear(See fig.1)Fig.4CD changer unitCard wireAdhesion tape1-7MX-G700RPrior to performing the following procedure, remove the metal cover and CD changer unit.Disconnect the card wire from the connector FCW3 on the main board.Disconnect the harness

45、 from the connector JCW1, JCW2 and HCW3 on the main board.Remove the screw E attaching the earth terminal extending from the cassette mechanism assembly. Remove the two screws F attaching the front panel assembly to the both sides of body.Remove the screw G attaching the main board to the front pane

46、l assembly.Remove the screw H attaching the front panel assembly to the bottom of body.Release the two joints1 and two joints2, and detach the front panel assembly toward the front.1.2.3.4.5.6.7.Removing the front panel assembly (See Fig.8 to 10)Fig.6Fig.7Fig.5RCW6CD boardCD changer unitMain boardCW

47、105CW107Rear panelCD(both sides)Rear panelCD changer unitFront panelassemblyFig.8Fig.9Main boardFCW3JCW2JCW1HCW3ACW1ACW2Front panelassemblyJoint1(both sides)F(both sides)Joint1(both sides)F(both sides)E(fixing the earth wire)Front panelassemblyGMain boardAmp. boardACW5ACW6MX-G700R1-8Prior to perform

48、ing the following procedure, remove the metal cover and CD changer unit.Disconnect the card wire from the connector ACW1 and the harness from the connector ACW2, ACW5 and ACW6 on the amp. board. Remove the four screws I attaching the heat sink cover to the rear panel. Remove the heat sink cover.Remo

49、ve the four screws J attaching the heat sink and two screws K attaching the speaker terminal to the rear panel. After moving the heat sink upward, remove the claws. Then pull out the heat sink & amp. board inward.1.2.3.4.Removing the heat sink & amp. board (See Fig.8, 11 and 12)Prior to performing t

50、he following procedure, remove the metal cover.Disconnect the card wire from the connector CON01 on the tuner board.Remove the two screws M attaching the tuner board to the rear panel. Prior to performing the following procedure, remove the metal cover and heat sink cover.Disconnect the harness from