Aiwa-NSXT929-cs-sm维修电路原理图.pdf

《Aiwa-NSXT929-cs-sm维修电路原理图.pdf》由会员分享，可在线阅读，更多相关《Aiwa-NSXT929-cs-sm维修电路原理图.pdf（43页珍藏版）》请在收音机爱好者资料库上搜索。

1、SERVICE MANUALDATANSX-T929RC-ZAS04SYSTEMCDCASSEIVERREMOTE CONTROLLERCX-NT929COMPACT DISC STEREOSYSTEMBASIC TAPE MECHANISM : 2ZM-3MK2 PR7NMBASIC CD MECHANISM : 6ZG-1 ZZRNDMNSX-T929LHS/M Code No. 09-013-440-2R1 This Service Manual is the “Revision Publishing” and replaces “Simple Manual” of NSX-T929 (

2、LH), (S/M Code No. 09-00C-440-2T1). If requiring information about the CD mechanism, see Service Manual of 6ZG-1,(S/M Code No. 09-001-338-7N8).SPEAKERSX-WNT929REVISIONRadioFans.CN 收音机爱 好者资料库 2 SPECIFICATIONSTuning range87.5 MHz to 108 MHzUsable sensitivity (IHF)13.2 dBfAntenna terminals75 ohms (unba

3、lanced)Tuning range531 kHz to 1602 kHz (9 kHz step)530 kHz to 1710 kHz (10 kHz step)Usable sensitivity350 V/mAntennaLoop antennaPower outputRated: 250 W + 250 W(8 ohms, T.H.D. 1 %, 60Hz )Reference: 320 W + 320 W(8 ohms, T.H.D. 10 %, 60Hz )Total harmonic distortion0.3 % (125 W, 60Hz, 8 ohms,DIN AUDIO

4、)InputsVIDEO/AUX: 300 mV (adjustable)MD: 300 mV (adjustable)MIC 1, MIC 2: 1.0 mV (10 kohms)OutputsLINE OUT: 210 mVSPEAKERS: accept speakers of8 ohms or moreSURROUND SPEAKERS:accept speakers of 8 ohms to 16 ohmsPHONES (stereo jack): acceptsheadphones of 32 ohms or moreTrack format4 tracks, 2 channels

5、 stereoFrequency responseCrO2 tape: 50 Hz 16000 HzNormal tape: 50 Hz 15000 HzSignal-to-noise ratio60 dB (Dolby B NR ON, CrO2 tapepeak level)Recording systemAC biasHeadsDeck 1: Playback head x 1Deck 2: Recording/playback head x 1,erase head x 1LaserSemiconductor laser ( =780 nm)D-A converter1 bit dua

6、lSignal-to-noise ratio85 dB (1 kHz, 0 dB)Harmonic distortion0.05 % (1 kHz, 0 dB)Power requirements120 V/ 220V230V/ 240 V AC(switchable) 50/60 HzPower consumption390 WPower consumption inWith ECO mode on: 0.9 Wstandby modeWith ECO mode off: 47 WDimensions (W x H x D)300 x 383.5 x 404.5 mmWeight of ma

7、in unit17.2 kgSpeaker system3 way,built-in subwoofer(magnetic shielded type)Speaker unitsWoofer: 160 mm X 2 coneMid range: 140 mm coneSuper tweeter: 20 mm ceramicImpedance8 ohms / 8 ohmsDimensions (W x H x D)270 x 495 x 297 mmWeight6.5 kg Manufactured under license from Dolby Laboratories Licensing

8、Corporation. “DOLBY” and the double-D symbol are trademarks of Dolby Laboratories Licensing Corporation. The word “BBE” and the “BBE symbol” are trademarks of BBE Sound, Inc. Under license from BBE Sound, Inc. Design and specifications are subject to change without notice.RadioFans.CN 收音机爱 好者资料库 3 C

9、LASS 1LASER PRODUCTKLASSE 1LASER PRODUKTLUOKAN 1LASER LAITEKLASS 1LASER APPARATThis set employs laser. Therefore, be sure to follow carefullythe instructions below when servicing.WARNING!WHEN SERVICING, DO NOT APPROACH THE LASEREXIT WITH THE EYE TOO CLOSELY. IN CASE IT ISNECESSARY TO CONFIRM LASER B

10、EAM EMISSION.BE SURE TO OBSERVE FROM A DISTANCE OF MORETHAN 30cm FROM THE SURFACE OF THE OBJEC-TIVE LENS ON THE OPTICAL PICK-UP BLOCK.sCaution: Invisible laser radiation whenopen and interlocks defeated avoidexposure to beam.sAdvarsel: Usynlig laserstling ved bning,nr sikkerhedsafbrydere er ude af f

11、unktion.Undg udsttelse for strling.VAROITUS!Laiteen Kyttminen muulla kuin tss kyttohjeessamainitulla tavalla saataa altistaa kyt-tjnturvallisuusluokan 1 ylittvlle nkymttmllelasersteilylle.VARNING!Om apparaten anvnds p annat stt n vad somspecificeras i denna bruksanvising, kan anvndarenutsttas fr osy

12、nling laserstrlning, som verskridergrnsen fr laserklass 1.PROTECTION OF EYES FROM LASER BEAM DURING SERVICINGCAUTIONUse of controls or adjustments or performance of proce-dures other than those specified herin may result inhazardous radiation exposure.ATTENTIONLutillisation de commandes, rglages ou

13、procduresautres que ceux spcifis peut entraner une dangereuseexposition aux radiations.ADVARSELUsynlig laserstling ved bning, nr sikkerhedsafbrydereerude af funktion. Undg udsttelse for strling.This Compact Disc player is classified as a CLASS 1LASER product.The CLASS 1 LASER PRODUCT label is locate

14、d on therear exterior.Precaution to replace Optical block(KSS-213F)Body or clothes electrostatic potential couldruin laser diode in the optical block. Be sureground body and workbench, and use care theclothes do not touch the diode.1) After the connection, remove solder shown inright figure.PICK-UP

15、Assy PWBSolderRadioFans.CN 收音机爱 好者资料库 4 NOTE ON BEFORE STARTING REPAIRCharging voltage (V)Discharging Rated power (W)Parts number(C101, 102)resistor ()25-48100387-A00-247-09049-140220587-A00-232-090Note: The reference numbers (C101, C102) of the electrolytic capacitors can change depending on the mo

16、dels. Be sure to check thereference numbers of the charging capacitors on schematic diagram before starting the discharging work.2. Check items before exchanging the MICROCOMPUTERBe sure to check the following items before exchanging the MICROCOMPUTER. Exchange the MICROCOMPUTER after confirmingthat

17、 the MICROCOMPUTER is surely defective.2-1. Regarding the HOLD terminal of the MICROCOMPUTERWhen the HOLD terminal (INPUT) of the MICROCOMPUTER is “H”, the MICROCOMPUTER is judged to be operating correctly.When this terminal is “L”, the main power cannot be turned on. Therefore, be sure to check the

18、 terminal voltage of the HOLDterminal before exchange.When the MICROCOMPUTER is not defective, the HOLD terminal can also go “L” when the POWER AMPLIFIER has anyabnormalities that triggers the abnormality detection circuit on the MAIN C. B. that sets the HOLD terminal to “L”.Good or no good judgemen

19、t of the MICROCOMPUTER11111Turn on the AC main power.22222Confirm that the main power is turned on and the HOLD terminal of the MICROCOMPUTER keeps the “H” level or not.33333When the HOLD terminal is “L” level, the abnormality detection circuit is judged to be working correctly and theMICROCOMPUTER

20、is judged to be good.1. Forced discharge of electrolytic capacitor of power supply blockWhen repair is going to be attempted in the set that uses relay circuit in the power supply block, electric potential is kept charged acrossthe electrolytic capacitors (C101, 102) even though AC power cord is rem

21、oved. If repair is attempted in this condition, secondary defectcan occur.In order to prevent the secondary trouble, perform the following measures before starting repair work.Discharge procedure11111Remove the AC power cord.22222Connect a discharging resistor at an end of lead wire thathas clips at

22、 both ends. Connect the other end of the leadwire to metal chassis.33333Contact the other end of the discharging resistor to thepositive (+) side (+VH) of C101. (For two seconds)44444Contact the same end of the discharging resistor as step33333 to the negative (-) side (-VH) of C102 in the same way.

23、(For two seconds)55555Check that voltage across C101 and C102 has decreasedto 1 V or less using a multimeter or an oscilloscope.Select a discharging resistor referring to the following table.Fig-1MAIN C.BD101C101C1022234RadioFans.CN 收音机爱 好者资料库 5 In such a case, check also if the POWER AMPLIFIER circ

24、uit or power supply circuit has any abnormalities or not.2-2. Regarding resetThere are cases that the machine does not work correctly because the MICROCOMPUTER is not reset even though the AC powercord is re-inserted, or the software reset (pressing the STOP key + POWER key) is performed.When the ab

25、ove described phenomenon occurs, it can lead to wrong judgement as if the MICROCOMPUTER is defective and toexchange the MICROCOMPUTER. In such a case, perform the forced-reset by the following procedure and check good or nogood of the MICROCOMPUTER.11111Remove the AC power cord.22222Short both ends

26、of the electrolytic capacitor C113 that is connected to VDD of the MICROCOMPUTER with tweezers.33333Connect the AC power cord again. If the MICROCOMPUTER returns to the normal operation, the MICROCOMPUTER isgood.Note: The reference number or MICROCOMPUTER pin number of transistor (Q110) and electrol

27、ytic capacitor (C113) can change dependingon the models. Be sure to check the reference numbers on schematic diagram before starting the discharging work.2-3. Confirmation of soldering state of MICROCOMPUTERCheck the soldering state of the MICROCOMPUTER in addition to the above described procedures.

28、 Be sure to exchange theMICROCOMPUTER after surely confirming that the trouble is not caused by poor soldering but the MICROCOMPUTER itself.Fig-2-2MICRO-COMPUTERMICROCOMPUTERFRONT C.BFRONT C.BVSSVDDC113*%C1131815Short with tweezers.RadioFans.CN 收音机爱 好者资料库 6 ELECTRICAL MAIN PARTS LISTDESCRIPTIONREF.

29、NO.KANRINO.PART NO.DESCRIPTIONREF. NO.KANRINO.PART NO.IC 87-A21-419-040 C-IC,NJM14558MD-TE2 8B-NF4-635-010 C-IC,LC876596W-5T96 87-A21-831-010 IC,SPS-422-1-F1 87-A20-355-010 IC,CXA1553P 87-A20-783-040 C-IC,BA7762AFS 87-A21-021-040 C-IC,BU2099FV 87-070-289-040 IC,BU2092F 87-A21-018-040 C-IC,M65849BFP6

30、31D 87-A21-452-130 C-IC,BD3876AKS2 87-A21-051-040 C-IC,BU9990-03FS 87-A21-695-010 IC,LA1845L 87-A21-577-040 C-IC,M61506FP 87-A21-928-010 IC,LC72131D-N 87-A21-269-010 IC,EW732TRANSISTOR 89-213-702-010 TR,2SB1370 (1.8W) 87-A30-087-080 C-FET,2SK2158 87-A30-455-040 C-TR,DTA144EKA 87-A30-515-080 TR,2SA19

31、79O/Y 87-A30-075-080 C-TR,2SA1235F 87-A30-076-080 C-TR,2SC3052F 87-A30-086-070 C-TR,CSD1306E 89-213-750-010 TR,2SB1375 (25W) 89-110-372-080 C-TR,2SA1037K(R) 87-026-610-080 TR,KTC3198GR 87-A30-495-080 TR,2SA1981Y 87-A30-107-070 C-TR,CMBT5401 87-A30-106-040 C-TR,CMBT5551 87-A30-190-080 TR,CC5551 87-A3

32、0-523-010 TR,2SD2562 87-A30-522-010 TR,2SB1649 87-A30-218-080 TR,2SB1237(Q) 87-026-609-080 TR,KTA1266GR 87-A30-447-040 C-TR,DTA114EKA 87-A30-427-040 C-TR,DTC114EKA 87-A30-097-010 TR,FN1016 87-A30-098-010 TR,FP1016 87-A30-276-040 C-TR,DTA143EKA 87-A30-186-010 FET,2SK3053 87-A30-582-080 TR,CDA1585BC 8

33、7-A30-318-080 TR,CSA952K 89-327-143-010 C-TR,2SC2714(0) 87-A30-489-080 C-TR,KRA107S 89-503-602-080 C-FET,2SK360E 87-A30-234-080 TR,CSC4115BC 87-026-463-080 TR,2SA933S (0.3W)DIODE 87-020-465-080 DIODE,1SS133 (110MA) 87-A40-224-010 DIODE,GBU8DL 87-A40-673-090 DIODE,D10XB20 87-A40-269-080 C-DIODE,MC283

34、6 87-A40-270-080 C-DIODE,MC2838 87-A40-784-080 ZENER,UZ39BSB 87-A40-764-080 ZENER,UZ10BSC 87-A40-553-080 DIODE,1N4003 LES 87-A40-488-080 DIODE,1SS244 87-A40-234-080 ZENER,MTZJ5.6A 87-A40-747-080 ZENER,UZ5.1BSB 87-A40-646-010 DIODE,FMB-G16L 87-A40-313-080 C-DIODE,MC2840 87-A40-751-080 ZENER,UZ6.2BSB

35、87-A40-745-080 ZENER,UZ4.7BSA 87-A40-392-080 DIODE,1N5818-T 87-A40-749-080 ZENER,UZ5.6BSB 87-017-149-080 ZENER,HZS6A2LMAIN C.B C11 87-A12-317-080 C-CAP,U 0.1-50 Z F C12 87-A12-317-080 C-CAP,U 0.1-50 Z F C13 87-A12-317-080 C-CAP,U 0.1-50 Z F C14 87-A12-317-080 C-CAP,U 0.1-50 Z F C15 87-A10-122-090 CA

36、P,E 6800-65 VR C16 87-A10-122-090 CAP,E 6800-65 VR C19 87-016-035-090 CAP, E 6800-35 VR C20 87-016-035-090 CAP, E 6800-35 VR C31 87-A12-062-080 CAP,E 100-10 SMG C32 87-012-286-080 C-CAP,U 0.01-25 K B C33 87-A12-071-080 CAP,E 47-25 SMG C34 87-A12-089-080 CAP,E 3.3-50 SMG C35 87-012-286-080 C-CAP,U 0.

37、01-25 KB C36 87-A12-062-080 CAP,E 100-10 SMG C37 87-A12-072-080 CAP,E 100-25 SMG C38 87-A12-092-080 CAP,E 22-50 SMG C39 87-A12-066-080 CAP,E 47-16 SMG C40 87-A12-074-080 CAP,E 470-25 SMG C113 87-012-195-080 C-CAP,U 100P-50CH C114 87-012-195-080 C-CAP,U 100P-50CH C117 87-A12-317-080 C-CAP,U 0.1-50 Z

38、F C118 87-A12-317-080 C-CAP,U 0.1-50 Z F C127 87-A12-317-080 C-CAP,U 0.1-50 Z F C131 87-A12-087-080 CAP,E 1-50 SMG C132 87-A12-061-080 CAP,E 47-10 SMG C133 87-A12-071-080 CAP,E 47-25 SMG C301 87-012-188-080 C-CAP,U 47P-50 CH C302 87-012-188-080 C-CAP,U 47P-50 CH C303 87-012-336-080 C-CAP,U 330P-50 J

39、 SL C304 87-012-336-080 C-CAP,U 330P-50 J SL C305 87-012-336-080 C-CAP,U 330P-50 J SL C306 87-012-336-080 C-CAP,U 330P-50 J SL C307 87-010-759-080 C-CAP,U 0.1-25F C311 87-010-787-080 CAP, U 0.022-25 K B C312 87-010-787-080 CAP, U 0.022-25 K B C313 87-012-276-080 C-CAP,U 1500P-50 B C314 87-012-276-08

40、0 C-CAP,U 1500P-50 B C315 87-012-274-080 CHIP CAP,U 1000P-50B C316 87-012-274-080 CHIP CAP,U 1000P-50B C317 87-A10-706-080 C-CAP,U 0.33U-16 F Z C318 87-A10-706-080 C-CAP,U 0.33U-16 F Z C319 87-A10-025-080 C-CAP,U 0.22-16Z F C320 87-A10-025-080 C-CAP,U 0.22-16Z F C321 87-A10-025-080 C-CAP,U 0.22-16Z

41、F C322 87-A10-025-080 C-CAP,U 0.22-16Z F C324 87-A12-071-080 CAP,E 47-25 SMG C325 87-A12-057-080 CAP,E 330-6.3 SMG C327 87-A12-090-080 CAP,E 4.7-50 SMG C328 87-A12-090-080 CAP,E 4.7-50 SMG C332 87-010-759-080 C-CAP,U, 0.1-25F C335 87-A12-087-080 CAP,E 1-50 SMG C336 87-A12-087-080 CAP,E 1-50 SMG C337

42、 87-010-759-080 C-CAP,U 0.1-25F C339 87-010-759-080 C-CAP,U 0.1-25F C340 87-010-759-080 C-CAP,U 0.1-25F C351 87-A10-039-080 C-CAP,U 470P-50 J CH C352 87-A10-039-080 C-CAP,U 470P-50 J CH C354 87-010-175-080 C-CAP,S 560P-50 J SL C355 87-012-274-080 CHIP CAP,U 1000P-50B C356 87-A12-071-080 CAP,E 47-25

43、SMG C357 87-012-286-080 CAP, U 0.01-25 C358 87-012-279-080 C-CAP,U 2700P-50 B C359 87-012-279-080 C-CAP,U 2700P-50 B C360 87-012-279-080 C-CAP,U 2700P-50 B C363 87-A12-361-080 CAP,M 5600P-100 J CP C370 87-010-759-080 C-CAP,U, 0.1-25F C371 87-012-271-080 C-CAP, U 560P-50 C372 87-012-271-080 C-CAP, U

44、560P-50 C373 87-012-275-080 C-CAP,U 1200P-50 BRadioFans.CN 收音机爱 好者资料库 7 DESCRIPTIONREF. NO.KANRINO.PART NO.DESCRIPTIONREF. NO.KANRINO.PART NO. C374 87-012-275-080 C-CAP,U 1200P-50 B C375 87-A12-084-080 CAP,E 0.22-50 SMG C376 87-A12-084-080 CAP,E 0.22-50 SMG C378 87-010-759-080 C-CAP,U 0.1-25F C381 8

45、7-012-286-080 CAP, U 0.01-25 C382 87-012-188-080 C-CAP,U 47P-50 CH C383 87-012-286-080 CAP, U 0.01-25 C384 87-A12-088-080 CAP,E 2.2-50 SMG C385 87-012-280-080 CAP, U 3300P-50 C386 87-010-759-080 C-CAP,U 0.1-25F C388 87-012-199-080 C-CAP,U 220P-50 J CH C501 87-A12-062-080 CAP,E 100-10 SMG C502 87-010

46、-759-080 C-CAP,U 0.1-25F C503 87-A10-353-080 C-CAP,U 0.22-10KB C504 87-A10-353-080 C-CAP,U 0.22-10KB C505 87-A10-025-080 C-CAP,U 0.22-16Z F C506 87-012-280-080 CAP, U 3300P-50 C507 87-010-986-080 C-CAP,S 820P-25 J CH C508 87-A12-319-080 C-CAP,U 0.1-25 K B C509 87-A12-319-080 C-CAP,U 0.1-25 K B C510

47、87-012-280-080 CAP, U 3300P-50 C511 87-010-986-080 C-CAP,S 820P-25 J CH C512 87-A10-025-080 C-CAP,U 0.22-16Z F C513 87-A12-083-080 CAP,E 0.1-50 SMG C514 87-A12-061-080 CAP,E 47-10 SMG C515 87-A12-087-080 CAP,E 1-50 SMG C516 87-A12-087-080 CAP,E 1-50 SMG C517 87-012-279-080 C-CAP,U 2700P-50 B C518 87

48、-012-279-080 C-CAP,U 2700P-50 B C531 87-A12-091-080 CAP,E 10-50 SMG C532 87-010-759-080 C-CAP,U 0.1-25F C533 87-010-759-080 C-CAP,U 0.1-25F C534 87-012-199-080 C-CAP,U 220P-50 J CH C535 87-012-274-080 CHIP CAP,U 1000P-50B C536 87-010-759-080 C-CAP,U 0.1-25F C537 87-012-188-080 C-CAP,U 47P-50 CH C538

49、 87-012-188-080 C-CAP,U 47P-50 CH C539 87-012-188-080 C-CAP,U 47P-50 CH C541 87-012-274-080 CHIP CAP,U 1000P-50B C609 87-012-277-080 C-CAP, U 1800P-50 B C610 87-012-277-080 C-CAP, U 1800P-50 B C611 87-010-956-080 CHIP-CAP,S 0.068-25B C612 87-016-369-080 C-CAP,S 0.033-25 B K C613 87-012-286-080 C-CAP

50、, U 0.01-25 C614 87-012-286-080 C-CAP, U 0.01-25 C615 87-A12-319-080 C-CAP, U 0.1-25 K B C616 87-A10-260-080 C-CAP, U 0.1-16 K B C617 87-010-829-080 C-CAP, U 0.047-16 C618 87-A12-087-080 CAP,E 1-50 SMG C619 87-A12-062-080 CAP,E 100-10 SMG C620 87-012-277-080 C-CAP, U 1800P-50 B C622 87-A12-071-080 C