Aiwa-NSXAJ14-cs-sm维修电路原理图.pdf

《Aiwa-NSXAJ14-cs-sm维修电路原理图.pdf》由会员分享，可在线阅读，更多相关《Aiwa-NSXAJ14-cs-sm维修电路原理图.pdf（47页珍藏版）》请在收音机爱好者资料库上搜索。

1、SERVICE MANUALCOMPACT DISC STEREOCASSETTE RECEIVERBASIC TAPE MECHANISM : ZZM-2 PR1NMBASIC CD MECHANISM : AZG-1 ZA3RNDMNSX-AJ14NSX-BL14ENSX-BL14NSX-BL16UHAHS, EZ, KEZS/M Code No. 09-004-428-8R2REVISION If requiring information about the CD mechanism, see Service Manual of AZG-1 (S/M Code No. 09-001-3

2、35-3NC). This Service Manual is the “Revision Publishing” and replaces “Simple Manual” NSX-AJ14(U)/BL14E(HA)/BL14(HS,EZ,K)/BL16(EZ),(S/M Code No. 09-003-428-8T2).DATANSX-AJ14SPEAKERSYSTEMCDCASSEIVERREMOTECONTROLLERNSX-BL14NSX-BL16CX-NAJ14SX-NAJ11CX-NBL14SX-NBL11SX-NBL16RC-ZAS02NSX-BL14ECX-NBL14ESX-N

3、BL17RadioFans.CN 收音机爱 好者资料库 2 Tuning range87.5 MHz to 108 MHzUsable sensitivity (IHF)U,HA,HS: 13.2 dBfEZ,K: 16.8 dBfAntenna terminals75 ohms (unbalanced)Tuning range530 kHz to 1710 kHz (10 kHz step)531 kHz to 1602 kHz (9 kHz step)Usable sensitivity350 V/mAntennaLoop antennaTuning range144 kHz to 290

4、 kHzUsable sensitivity1400 V/mAntennaLoop antennaPower outputRatedU: 10 W + 10 W (50 Hz - 20 kHz,T.H.D. less than 1%, 6 ohms) 15 W + 15 W(1 kHz, T.H.D. less than 10%, 6 ohms)HA: 28 W + 28 W (1 kHz, T.H.D. 1%,6 ohms)Reference: 35 W + 35 W(1 kHz, T.H.D. 10%, 6 ohms)HS: 17 W + 17 W (1 kHz, T.H.D. 1%,6

5、ohms)Reference: 20 W + 20 W(1 kHz, T.H.D. 10%, 6 ohms)EZ,K: 12 W + 12 W (1 kHz/DIN 45500,T.H.D. 1%, 6 ohms)Reference: 15 W + 15 W(1 kHz/DIN 45324, T.H.D. 10%, 6 ohms)EZ:DIN MUSIC POWER: 30 W + 30 WTotal harmonic distortion U,EZ,K: 0.1% (6 W, 1 kHz, 6 ohms,DIN AUDIO)HA: 0.1% (14 W, 1 kHz, 6 ohms,DIN

6、AUDIO)HS: 0.1% (8 W, 1 kHz, 6 ohms,DIN AUDIO)InputsVIDEO/AUX: 500 mVHS: MIC 1.8 mV(10 kohms)OutputsSPEAKERS: accept speakers of 6ohms or morePHONES (stereo jack) : acceptsheadphones of 32 ohms or moreTrack format4 tracks, 2 channels stereoFrequency response50 Hz - 8000 HzRecording systemAC biasHeads

7、Deck 1 : Recording/Playback head x 1, erase head x 1Deck 2 : Playback head x 1LaserSemiconductor laser ( =780 nm)D-A converter1 bit dualSignal-to-noise ratio85 dB (1 kHz, 0 dB)Harmonic distortion0.05 % (1 kHz, 0 dB)SX-NAJ11Speaker System2 way, bass reflex (magneticshielded type)Speaker unitsWoofer:1

8、20 mm (43/4 in.) cone typeTweeter:20 mm (13/16 in.) cone typeImpedance6 ohmsSensitivity87 dB/W/mDimensions (W x H x D)220 x 324 x 211 mm(83/4 x 127/8 x 83/8 in.)Weight2.0 kg (4 lbs 7 oz.)SPECIFICATIONSSX-NBL17,SX-NBL11, SX-NBL16Speaker System2 way, bass reflex (magnetic shieldedtype)Speaker unitsWoo

9、fer:120 mm cone typeTweeter:20 mm cone typeImpedance6 ohmsSensitivity87 dB/W/mDimensions (W x H x D)220 x 324 x 211 mmWeight2.0 kgPower requirementsU: 120 V AC, 60 HzHA: 120 V/220-230 V/240 V AC(switchable), 50/60 HzHS: 220 V AC, 60 HzEZ,K: 230 V AC, 50 HzPower consumptionU: 38 WHA: 55 WHS: 60 WEZ,K

10、: 45 WPower consumptionU: With power-economizing in standby modemode off : 8 WHA: With power-economizingmode off : 12 WHS,EZ,K: With power-economizingmode off : 14 WWith power-economizing mode on :0.9 WDimensions of main unitU,EZ,K:(W x H x D)260 x 324 x 348 mm(101/4 x 127/8 x 133/4 in.)HA,HS: 260 x

11、 324 x 348 mmWeight of main unitU: 4.8 kg (10 lbs 9 oz.)HA: 5.7 kgHS: 5.0 kgEZ,K: 4.9 kg Design and specifications are subject to change without notice.RadioFans.CN 收音机爱 好者资料库 3 CLASS 1LASER PRODUCTKLASSE 1LASER PRODUKTLUOKAN 1LASER LAITEKLASS 1LASER APPARATThis set employs laser. Therefore, be sure

12、 to follow carefullythe instructions below when servicing.WARNING!WHEN SERVICING, DO NOT APPROACH THE LASEREXIT WITH THE EYE TOO CLOSELY. IN CASE IT ISNECESSARY TO CONFIRM LASER BEAM EMISSION.BE SURE TO OBSERVE FROM A DISTANCE OF MORETHAN 30cm FROM THE SURFACE OF THE OBJEC-TIVE LENS ON THE OPTICAL P

13、ICK-UP BLOCK.sCaution: Invisible laser radiation whenopen and interlocks defeated avoidexposure to beam.sAdvarsel: Usynlig laserstling ved bning,nr sikkerhedsafbrydere er ude af funktion.Undg udsttelse for strling.VAROITUS!Laiteen Kyttminen muulla kuin tss kyttohjeessamainitulla tavalla saattaa alti

14、staa kyt-tjnturvallisuusluokan 1 ylittvlle nkymttmllelasersteilylle.VARNING!Om apparaten anvnds p annat stt n vad somspecificeras i denna bruksanvising, kan anvndarenutsttas fr osynling laserstrlning, som verskridergrnsen fr laserklass 1.PROTECTION OF EYES FROM LASER BEAM DURING SERVICINGCAUTIONUse

15、of controls or adjustments or performance of proce-dures other than those specified herein may result inhazardous radiation exposure.ATTENTIONLutillisation de commandes, rglages ou procduresautres que ceux spcifis peut entraner une dangereuseexposition aux radiations.ADVARSELUsynlig laserstling ved

16、bning, nr sikkerhedsafbrydereerude af funktion. Undg udsttelse for strling.This Compact Disc player is classified as a CLASS 1LASER product.The CLASS 1 LASER PRODUCT label is located on therear exterior.PICK-UP ASSYP.C.BPrecaution to replace Optical block(KSS-213F)Body or clothes electrostatic poten

17、tial couldruin laser diode in the optical block. Be sureground body and workbench, and use care theclothes do not touch the diode.1) After the connection, remove solder shown inright figure.SOLDERRadioFans.CN 收音机爱 好者资料库 4 NOTE ON BEFORE STARTING REPAIRCharging voltage (V)Discharging Rated power (W)P

18、arts number(C101, 102)resistor ()25-48100387-A00-247-09049-140220587-A00-232-090Note: The reference numbers (C101, C102) of the electrolytic capacitors can change depending on the models. Be sure to check thereference numbers of the charging capacitors on schematic diagram before starting the discha

19、rging work.2. Check items before exchanging the MICROCOMPUTERBe sure to check the following items before exchanging the MICROCOMPUTER. Exchange the MICROCOMPUTER after confirmingthat the MICROCOMPUTER is surely defective.2-1. Regarding the HOLD terminal of the MICROCOMPUTERWhen the HOLD terminal (IN

20、PUT) of the MICROCOMPUTER is “H”, the MICROCOMPUTER is judged to be operating correctly.When this terminal is “L”, the main power cannot be turned on. Therefore, be sure to check the terminal voltage of the HOLDterminal before exchange.When the MICROCOMPUTER is not defective, the HOLD terminal can a

21、lso go “L” when the POWER AMPLIFIER has anyabnormalities that triggers the abnormality detection circuit on the MAIN C. B. that sets the HOLD terminal to “L”.Good or no good judgement of the MICROCOMPUTER11111Turn on the AC main power.22222Confirm that the main power is turned on and the HOLD termin

22、al of the MICROCOMPUTER keeps the “H” level or not.33333When the HOLD terminal is “L” level, the abnormality detection circuit is judged to be working correctly and theMICROCOMPUTER is judged to be good.1. Forced discharge of electrolytic capacitor of power supply blockWhen repair is going to be att

23、empted in the set that uses relay circuit in the power supply block, electric potential is kept charged acrossthe electrolytic capacitors (C101, 102) even though AC power cord is removed. If repair is attempted in this condition, secondary defectcan occur.In order to prevent the secondary trouble, p

24、erform the following measures before starting repair work.Discharge procedure11111Remove the AC power cord.22222Connect a discharging resistor at an end of lead wire thathas clips at both ends. Connect the other end of the leadwire to metal chassis.33333Contact the other end of the discharging resis

25、tor to thepositive (+) side (+VH) of C101. (For two seconds)44444Contact the same end of the discharging resistor as step33333 to the negative (-) side (-VH) of C102 in the same way.(For two seconds)55555Check that voltage across C101 and C102 has decreasedto 1 V or less using a multimeter or an osc

26、illoscope.Select a discharging resistor referring to the following table.Fig-1MAIN C.BD101C101C1022234RadioFans.CN 收音机爱 好者资料库 5 In such a case, check also if the POWER AMPLIFIER circuit or power supply circuit has any abnormalities or not.2-2. Regarding resetThere are cases that the machine does not

27、 work correctly because the MICROCOMPUTER is not reset even though the AC powercord is re-inserted, or the software reset (pressing the STOP key + POWER key) is performed.When the above described phenomenon occurs, it can lead to wrong judgement as if the MICROCOMPUTER is defective and toexchange th

28、e MICROCOMPUTER. In such a case, perform the forced-reset by the following procedure and check good or nogood of the MICROCOMPUTER.11111Remove the AC power cord.22222Short both ends of the electrolytic capacitor C113 that is connected to VDD of the MICROCOMPUTER with tweezers.33333Connect the AC pow

29、er cord again. If the MICROCOMPUTER returns to the normal operation, the MICROCOMPUTER isgood.Note: The reference number or MICROCOMPUTER pin number of transistor (Q110) and electrolytic capacitor (C113) can change dependingon the models. Be sure to check the reference numbers on schematic diagram b

30、efore starting the discharging work.2-3. Confirmation of soldering state of MICROCOMPUTERCheck the soldering state of the MICROCOMPUTER in addition to the above described procedures. Be sure to exchange theMICROCOMPUTER after surely confirming that the trouble is not caused by poor soldering but the

31、 MICROCOMPUTER itself.Fig-2-2MICRO-COMPUTERMICROCOMPUTERFRONT C.BFRONT C.BVSSVDDC113*%C1131815Short with tweezers.RadioFans.CN 收音机爱 好者资料库ELECTRICAL MAIN PARTS LISTDESCRIPTIONREF. NO.KANRINO.PART NO.DESCRIPTIONREF. NO.KANRINO.PART NO.IC 8A-NFA-616-010 C-IC,M38B59MFH-E251FP 8A-NFA-615-010 C-IC,M38B57M

32、CH-E236FP 87-A21-397-010 IC,STK490-070 87-A21-419-040 C-IC,NJM14558MD-TE2 87-A21-443-040 C-IC,M62495AFP 87-A21-415-010 IC,LA1843 87-A21-560-010 IC,LA1844L-A 87-070-127-110 IC,LC72131 D 87-A21-629-010 IC,SPS-442-10N 87-A21-482-010 IC,RPM6938-H4 87-A20-440-010 C-IC,BU1920FSTRANSISTOR 87-026-609-080 TR

33、,KTA1266GR 89-213-702-010 TR,2SB1370 (1.8W) 87-026-610-080 TR,KTC3198GR 87-A30-076-080 C-TR,2SC3052F 87-A30-075-080 C-TR,2SA1235F 87-A30-255-010 C-TR,2SB1342 87-A30-256-010 TR,2SD1933 87-A30-190-080 TR,CC5551 87-026-245-080 TR,DTC114ES 87-A30-198-080 TR,KTC3199GR 87-A30-090-080 FET,2SK2541 87-A30-48

34、4-080 C-TR,KRA102S 87-A30-468-080 C-TR,KRC102S-RTK 87-A30-107-070 C-TR,CMBT5401 87-A30-106-040 C-TR,CMBT5551 87-A30-091-080 FET,2SJ460 87-A30-062-080 C-TR,KRC104S 87-A30-318-080 TR,CSA952K 89-333-317-880 TR,2SC3331 (0.5W) 87-A30-234-080 TR,CSC4115BC 89-327-143-080 TR,2SC2714 (0.1W) 87-A30-489-080 C-

35、TR,KRA107S 89-503-602-080 C-FET,2SK360E 87-A30-086-070 C-TR,CSD1306E 87-A30-495-080 TR,2SA1981YDIODE 87-A40-736-080 DIODE,1N4148M (SEM) 87-020-465-080 DIODE,1SS133 (110MA) 87-A40-455-080 DIODE,RL203 GW 87-A40-553-080 DIODE,1N4003 LES 87-A40-774-080 ZENER,UZ24BSD 87-A40-764-080 ZENER,UZ10BSC 87-A40-3

36、13-080 C-DIODE,MC 2840 87-A40-270-080 C-DIODE,MC2838 87-A40-269-080 C-DIODE,MC2836 87-A40-768-080 ZENER,UZ16BSA 87-A40-752-080 ZENER,UZ6.2BSC 87-A40-739-080 ZENER,UZ2.7BSA 87-017-149-080 ZENER,HZS6A2L 87-A40-535-080 DIODE,1N5393-GOODARKMAIN C.B C3 87-010-196-080 CHIP CAPACITOR,0.1-25 C4 87-010-196-0

37、80 CHIP CAPACITOR,0.1-25 C5 87-010-196-080 CHIP CAPACITOR,0.1-25 C6 87-010-196-080 CHIP CAPACITOR,0.1-25 C9 87-010-196-080 CHIP CAPACITOR,0.1-25 C10 87-010-196-080 CHIP CAPACITOR,0.1-25 C11 87-010-196-080 CHIP CAPACITOR,0.1-25 C12 87-010-196-080 CHIP CAPACITOR,0.1-25 C19 87-A10-627-000 CAP,E 2200-50

38、 M SMG C20 87-A10-627-000 CAP,E 2200-50 M SMG C21 87-016-495-000 CAP,E 3300-25 M SMG C21 87-A10-520-000 CAP,E 3300-35 M SMG C22 87-016-495-000 CAP,E 3300-25 M SMG C22 87-016-051-000 CAP,E 2200-35 SMG C22 87-A10-011-090 CAP,E 2200-25 SMG C25 87-010-385-080 CAP, ELECT 220-25V C25 87-010-406-080 CAP, E

39、LECT 22-50 M 11L SME C25 87-010-407-080 CAP, ELECT 33-50 M 11L SME C26 87-010-247-080 CAP, ELECT 100-50V C26 87-010-406-080 CAP, ELECT 22-50 C30 87-010-247-080 CAP, ELECT 100-50V C30 87-010-384-080 CAP, ELECT 100-25M11LSME C31 87-010-263-080 CAP, ELECT 100-10V C32 87-010-197-080 CAP, CHIP 0.01 DM C3

40、3 87-010-263-080 CAP, ELECT 100-10V C34 87-010-247-080 CAP, ELECT 100-50V C35 87-010-406-080 CAP, ELECT 22-50 C36 87-010-381-080 CAP, ELECT 330-16V C38 87-A11-567-080 C-CAP,S 0.01-50 K B C38 87-010-190-080 C-CAP,S 0.01-50 ZF C50 87-010-384-080 CAP, ELECT 100-25 M 11L SME C60 87-010-403-080 CAP, ELEC

41、T 3.3-50V C97 87-010-196-080 CHIP CAPACITOR,0.1-25 C100 87-018-127-080 CAP TC-U 470P C101 87-010-183-080 C-CAP,S 2700P-50 B C101 87-010-185-080 C-CAP,S 3900P-50 KB C102 87-010-183-080 C-CAP,S 2700P-50 B C102 87-010-185-080 C-CAP,S 3900P-50 KB C103 87-010-545-080 CAP, ELECT 0.22-50V C104 87-010-545-0

42、80 CAP, ELECT 0.22-50V C105 87-010-178-080 CHIP CAP 1000P C105 87-010-186-080 CAP,CHIP 4700P C106 87-010-178-080 CHIP CAP 1000P C106 87-010-186-080 CAP,CHIP 4700P C107 87-010-404-080 CAP, ELECT 4.7-50V C107 87-010-403-080 CAP, ELECT 3.3-50V C108 87-010-404-080 CAP, ELECT 4.7-50V C108 87-010-403-080

43、CAP, ELECT 3.3-50V C109 87-010-322-080 C-CAP, S 100P-50JCH C109 87-010-179-080 C-CAP, S 1200P-50KB C110 87-010-322-080 C-CAP, S 100P-50JCH C110 87-010-179-080 C-CAP, S 1200P-50KB C111 87-010-391-080 CAP,E 10-35 SME C111 87-010-406-080 CAP, ELECT 22-50 C112 87-010-391-080 CAP,E 10-35 SME C112 87-010-

44、406-080 CAP, ELECT 22-50 C113 87-010-405-080 CAP, ELECT 10-50V C113 87-012-156-080 C-CAP, S 220P-50 J CH C113 87-A10-946-080 C-CAP, S 220P-100 J CH C114 87-010-405-080 CAP, ELECT 10-50V C114 87-012-156-080 C-CAP, S 220P-50 J CH C114 87-A10-946-080 C-CAP, S 220P-100 J CH C119 87-010-197-080 CAP, CHIP

45、 0.01 DM C120 87-010-197-080 CAP, CHIP 0.01 DM C123 87-010-197-080 CAP, CHIP 0.01 DM C124 87-010-197-080 CAP, CHIP 0.01 DM C125 87-012-368-080 C-CAP,S 0.1-50 F C125 87-010-196-080 CHIP CAPACITOR,0.1-25 C126 87-012-368-080 C-CAP,S 0.1-50 F C126 87-010-196-080 CHIP CAPACITOR,0.1-25 C127 87-012-368-080

46、 C-CAP,S 0.1-50 F C127 87-010-196-080 CHIP CAPACITOR,0.1-25 C128 87-012-368-080 C-CAP,S 0.1-50 F C128 87-010-196-080 CHIP CAPACITOR,0.1-25 C129 87-A11-572-080 C-CAP,S 0.015-50 K B C130 87-A11-572-080 C-CAP,S 0.015-50 K B C131 87-010-197-080 CAP, CHIP 0.01 DM C132 87-010-197-080 CAP, CHIP 0.01 DM C13

47、3 87-010-186-080 CAP,CHIP 4700P C140 87-010-182-080 C-CAP,S 2200P-50 B 6 RadioFans.CN 收音机爱 好者资料库DESCRIPTIONREF. NO.KANRINO.PART NO.DESCRIPTIONREF. NO.KANRINO.PART NO. C183 87-010-387-080 CAP,E 470-25 SME C184 87-010-403-080 CAP, ELECT 3.3-50V C185 87-018-209-080 CAP, TC U 0.1-50ZF C200 87-018-195-08

48、0 CAP TC-U 1200P C300 87-018-195-080 CAP TC-U 1200P C301 87-010-179-080 CAP,CHIP S B1200P C302 87-010-179-080 CAP,CHIP S B1200P C303 87-010-178-080 CHIP CAP 1000P C304 87-010-178-080 CHIP CAP 1000P C305 87-010-198-080 CAP, CHIP 0.022 C307 87-010-263-080 CAP, ELECT 100-10V C308 87-010-263-080 CAP, EL

49、ECT 100-10V C309 87-010-311-080 C-CAP, S 12P-50J CH C309 87-010-318-080 C-CAP, S 47P-50J CH C310 87-010-314-080 C-CAP, S 22P-50J CH C310 87-010-318-080 C-CAP, S 47P-50J CH C311 87-010-598-080 C-CAP,S 0.068-16VRK C312 87-010-598-080 C-CAP,S 0.068-16VRK C313 87-010-188-080 CAP,CHIP 6800P C314 87-010-1

50、88-080 CAP,CHIP 6800P C315 87-010-263-080 CAP, ELECT 100-10V C317 87-010-546-080 CAP, ELECT 0.33-50V C318 87-010-546-080 CAP, ELECT 0.33-50V C320 87-010-196-080 CHIP CAPACITOR,0.1-25 C321 87-010-196-080 CHIP CAPACITOR,0.1-25 C324 87-010-196-080 CHIP CAPACITOR,0.1-25 C325 87-010-196-080 CHIP CAPACITO