Laney-CD650-mix-sm 维修电路原理图.pdf
《Laney-CD650-mix-sm 维修电路原理图.pdf》由会员分享,可在线阅读,更多相关《Laney-CD650-mix-sm 维修电路原理图.pdf(19页珍藏版)》请在收音机爱好者资料库上搜索。
1、LaneyService InformationCD650 Mixer/AmplifierPart Number - SM3041RadioFans.CN 收音机爱 好者资料库LaneyContents1.DWG 30443.DWG 30104.DWG 9324 Preamp Diagram Channel8.Preset Adjustment on PCB 93239.DWG 9323 Power Amp Diagram15.Contact(Issue 2)Service Schematic2.DWG 2615 Mains WiringBlock Diagram5.DWG 9324 Prea
2、mp Diagram Masters6.DWG 9324 Preamp Diagram Channel7.DWG 9324 Preamp Diagram Masters10.DWG 9323 Power Amp Diagram11.Pre- amp PCB Assembly List12.Output PCB Assembly list13.Final Assembly List14.Cabinet Assembly List(Issue 2)(Issue 3)(Issue 3)(Issue 2)(Issue 3)RadioFans.CN 收音机爱 好者资料库23/11/99 Issue 1P
3、reset Adjustment PCB 9323To reset the amplifier bias following service or device replacement, follow these steps.1. Before powering up the unit for the first time after replacing devices, TurnR27,R28,R127 and R128 (All 1K presets) fully clockwise. This will bias the outputdevices into minimum conduc
4、tion. Failure to do this may result in the ampappearing to draw excessive current, Especially if powered through a “Current limit”device.2. Reset amplifier DC offset for Channel 1 by measuring between P2 (0V) and P107(Speaker). Set to 0V DC. 1mV, by Adjusting PS102.3. Reset amplifier DC offset for C
5、hannel 2 by measuring between P2 (0V) and P7(Speaker). Set to 0V DC. 1mV, by Adjusting PS2.4. Measure DC mV across TS109 Sense and Emitter junction. Adjust R128 until areading of 10mV 1mV is obtained.5. Measure DC mV across TS105 Sense And Emitter junction. Adjust R127 until areading of 10mV 1mV is
6、obtained.6. Recheck Across TS109 as above. Reset if necessary to 10mV.7. Check S, E junction of all four devices on channel 1 (TS105,TS109,TS111,TS114)This Should be 10mV 3mV. This completes Channel 1 re-biasing.8. Measure DC mV across TS9 Sense And Emitter junction. Adjust R28 until a readingof 10m
7、V 1mV is obtained.9. Measure DC mV across TS5 Sense And Emitter junction. Adjust R27 until a readingof 10mV 1mV is obtained.10. Recheck Across TS9 as above. Reset if necessary to 10mV.11. Double check S, E junction of all four devices on channel 2 (TS5,TS9,TS11,TS14)This Should be 10mV 3mV. This com
8、pletes the amplifier re-biasing.In practice, It may be easier to disconnect the Pre-Amp loom and facia from the rear chassis.Assembly List For ( 006347 ) Preamp PCB AssemblyStock CodeItemQty Req103815K .25W RESISTOR11300ORO SHORTING LINK691303100R 5% RESISTOR2130610K 5% RESISTOR4413091M 5% RESISTOR6
9、1310100K 5% RESISTOR251311470R 5% RESISTOR213124K7 5% RESISTOR1813148K2 5% RESISTOR22131547K 5% RESISTOR11131622K 5% RESISTOR13131739K 5% RESISTOR713186K8 5% RESISTOR1213263K3 5% RESISTOR3913271K 5% RESISTOR22133133K 5% RESISTOR31504 100R 2.5W RESISTOR 11920ZERO OHM RESISTOR38200447UF 50V RADIAL3201
10、310UF 50V CAPACITOR402014100UF 35V RADIAL120242.2UF 63V RADIAL1320251UF 63V RADIAL22026.47UF 63V RADIAL220274.7UF 63V RADIAL92200220NF 100V 10MM2240833NF 250V 10MM2240968NF 250V 10MM424131N5 100V 5mm824141NF 100V 5mm224152.2NF 100V 5mm1224174.7NF 100V 5mm42419100NF 63V 5mm9242022NF 100V 5mm2242110NF
11、 100V 5mm42423330PF 100V 5mm2242547NF 100V 5mm6242615NF 100V 5mm6260110PF 50V 10% COG6260247PF 50V 10% COG52603100PF 50V 10% COG62604270PF 50V 10% COG32605470PF 50V 10% COG212827680PF 50V CERAMIC230073V9 .5W ZENER DIODE130223mm GREEN LED730333mm LED RED1130343mm LED YELLOW230395V1 1.3W ZENER13500BAS
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- Laney-CD650-mix-sm 维修电路原理图 Laney CD650 mix sm 维修 电路 原理图