JBL-DVD600_MK2-dvd-sm 维修电路原理图.pdf

《JBL-DVD600_MK2-dvd-sm 维修电路原理图.pdf》由会员分享，可在线阅读，更多相关《JBL-DVD600_MK2-dvd-sm 维修电路原理图.pdf（63页珍藏版）》请在收音机爱好者资料库上搜索。

1、 Model DVD600IIDVD600II DVD/CD/CD-R/CD-RW/VCD Changer From the Cinema Propack 600II System Service Manual CONTENTS SPECIFICATIONS.2 SET-UP GUIDE.4 FRONT PANEL CONTROLS.7 FRONT PANEL DISPLAY.8 REAR PANEL CONNECTIONS.9 REMOTE CONTROL FUNCTIONS.10 OPERATION.14 BASIC TROUBLESHOOTING.21 EXPLODED VIEW.24

2、EXPLODED/MECHANICAL PARTS LIST25 SERVICE BULLETIN JBL2002-01.26 SERVICE BULLETIN JBL2003-01.28 SERVICE BULLETIN JBL2003-07.29 TECH TIP JBLTT2003-03.30 BLOCK DIAGRAM.31 IC901 MICROPROCESSOR.32 ELECTRICAL PARTS LIST38 PACKAGING44 PCB DRAWINGS.45 POWER SUPPLY50 SCHEMATICS.55 WIRING DIAGRAM.63 JBL Consu

3、mer Products 250 Crossways Park Dr. Woodbury, New York 11797 Rev2 9/2005 RadioFans.CN 收音机爱 好者资料库2Playback Media:5-inch (12cm) or 3-inch (8cm) DVD-Video: Region 1, single or dual sides/layers, linear PCM, Dolby Digital or DTSCD, CD-R, CD-RW: Linear PCM Audio MP3Video CD (VCD): MPEG-1 Video, Linear PC

4、M AudioVideo Section:Signal format:NTSCComposite Output:1V p-p/75 ohms, sync, negative polarityS Output:Y/Luminance: 1V p-p/75 ohms, sync, negative polarityC/Chrominance: 0.286V p-pComponent Outputs:Y: 1V p-p/75 ohms, sync, negative polarityPr: 0.648V p-p/75 ohmsPb: 0.648V p-p/75 ohmsAudio Section:C

5、oaxial Digital Output:0.5V p-p/75 ohmsFrequency Response:2Hz to 22kHz, +/ 0.5dB (44.1kHz sampling rate)Dynamic Range:DVD: 105dB (20-bit)CD: 100dBChannel Separation:90dBTHD:0.0035%Signal-to-Noise Ratio:100 dBWow and Flutter:below measurable limitsGeneral:Unit Power Consumption:25WUnit Dimensions:Widt

6、h: 17.3 inches (440mm)Height: 5.1 inches (130mm)Depth: 16.9 inches (420mm)Unit Weight:14.4 lb (7.6kg)Depth measurement includes knobs and buttons.Height measurement includes feet and chassis.All features and specifications are subject to change without notice.Technical SpecificationsDVD600IIThis pro

7、duct incorporates copyright protection technology that is protected by method claims of certain U.S. patents and other intellectual property rights owned by Macrovision Corporation and other rights owners. Use of this copyright protection technology must be authorized by Macrovision Corporation and

8、is intended for home and other limited viewing uses only, unless otherwise authorized by Macrovision Corporation. Reverse engineering or disassembly is prohibited. DVD600II DVD600II RadioFans.CN 收音机爱 好者资料库DATE:SEP 26.20011. Audio* Test Disc : YEDS 7(Sony),EIAJ CD- 1Coaxial(75)2. Video(75? Terminated

9、) - - - NTSC VIDEO * Test Disc : Navigation Vol 1 FOR SYSTEM(DVD- NF200) * VM700TC- VideoOutput levelY/Cb/CrVideoRCA JACK S/NS- JACK S/NRCA JACK Freq. Resp.S- JACK Freq.RespVideo S/N 100% FlatVideo S/N50% Flat 100% Color BarWTD : Off, SC TRAP OnBPF : 100KHz 5.0MHz 100% Color Bar1 - 1 - 8 -LPF : 500K

10、Hz1 - 1 - 1HPF : 10KHz 75% Color BarDataFrequency ResponseNominal SpecNorminal Spec40 IRE 1.0V 0.1(p- p) 1.0V 0.1(p- p)Frequency Response C- Video S - Video C- Video S - Video C- Video S - Video C- Video S - Video Cr Output Level 0.286V(p- p) 20%02.5dB55dB60dB1.0V(p- p) 10% Cb Output Level0.7V(p- p)

11、 20% Y Output Level0.7V(p- p) 20%Color Burst Error55dBColor S/N AM/PM150Hz120Hz60dBColor S/N AM/PM RCA Jack Color S/N S- Jack Color S/NOutput LevelItem (Y)Output LevelS - Video (C)Output Level RCA JACK LevelItemTest TrackTest ConditionsLimite Spec1Limite SpecTest ConditionsTest Trac0.5 + 0.05V(p- p)

12、1 - 1 - 7100% Flat100% Flat1 - 1 - 7100% FlatData100% Red Color4.2 MHz0.5MHz(NTSC)Multiburst1 - 1 - 61 - 1 - 11 - 1 - 8 - 1 - 1 - 1 DVD600II DVD600II 34Quick Installation DiagramsBASIC INSTALLATION: Your TV must at a minimum have a composite video input(this connector usually has a yellow-colored co

13、re), and Left (usually has awhite-colored core) and Right (red-colored core) Stereo audio preamp-levelRCA outputs. All wires for this hookup are included. TVVIDEO INAUDIO INLRAUDIO OUTLRVIDEO OUTS-VIDEO INS-VIDEO OUTCOMPONENTVIDEO INPrPbYWhiteRedDCR600IIDVD600IICONNECT TOAC OUTLETCONNECT TOAC OUTLET

14、YellowYellowBlackOrangeNOTES: 1. CONNECT “RIDGED” WIRE TO (+) COLORED TERMINAL AND CONNECT “SMOOTH” WIRE TO () BLACK TERMINAL ON DCR600II AND SPEAKERS.2. WIRE COLOR CODES ARE FOR EASE OF CONNECTION. THE SPEAKER WIRES CAN BE INTERCHANGED IF NECESSARY.(+)Ridges +SURROUND RIGHT SPEAKER +SURROUND LEFT S

15、PEAKER +FRONT RIGHT SPEAKER +FRONT LEFTSPEAKER +CENTER SPEAKER +SUBWOOFERGrayGreenRedWhiteBrownBlue DVD600II DVD600II 5Quick Installation DiagramsTVVIDEO INAUDIO INLRAUDIO OUTLRVIDEO OUTS-VIDEO INS-VIDEO OUTCOMPONENTVIDEO INPrPbYWhiteRedDCR600IIDVD600IICONNECT TOAC OUTLETCONNECT TOAC OUTLETBlackOran

16、ge()(+)Ridges +SURROUND RIGHT SPEAKER +SURROUND LEFT SPEAKER +FRONT RIGHT SPEAKER +FRONT LEFTSPEAKER +CENTER SPEAKER +SUBWOOFERALTERNATE INSTALLATION FOR BETTER PICTURE QUALITY: Your TV must have an S-Video input, and Left (usually has a white-colored core) and Right (red-colored core) Stereo audio

17、preamp-level RCA outputs. Two pieces of S-Video cable are not included and should be purchased separately.NOTES: 1. CONNECT “RIDGED” WIRE TO (+) COLORED TERMINAL AND CONNECT “SMOOTH” WIRE TO () BLACK TERMINAL ON DCR600II AND SPEAKERS.2. WIRE COLOR CODES ARE FOR EASE OF CONNECTION. THE SPEAKER WIRES

18、CAN BE INTERCHANGED IF NECESSARY.S-Video cable not includedS-Video cable not includedGrayGreenRedWhiteBrownBlue DVD600II DVD600II 6Quick Installation DiagramsTVVIDEO INAUDIO INLRAUDIO OUTLRVIDEO OUTS-VIDEO INS-VIDEO OUTCOMPONENTVIDEO INPrPbYWhiteRedDCR600IIDVD600IICONNECT TOAC OUTLETCONNECT TOAC OUT

19、LETYellowBlackOrange(+)Ridges + SURROUND RIGHT SPEAKER + SURROUND LEFT SPEAKER +FRONT RIGHT SPEAKER +FRONT LEFT SPEAKER +CENTER SPEAKER +SUBWOOFERYellowALTERNATE INSTALLATION FOR BEST PICTURE QUALITY: Your TV must have Y/Pr/Pb component video inputs (three separate RCA connectors with red-, blue- an

20、d green-colored cores), and Left (usually has a white-colored core) and Right (red-colored core) Stereo audio preamp-level RCA outputs. The component video cable is not included and should be purchased separately. This setup requires that the TVs own video switching is utilized to access the DVD pic

21、ture. All other video switching is still done through the DCR600II.NOTES: 1. CONNECT “RIDGED” WIRE TO (+) COLORED TERMINAL AND CONNECT “SMOOTH” WIRE TO () BLACK TERMINAL ON DCR600II AND SPEAKERS.2. WIRE COLOR CODES ARE FOR EASE OF CONNECTION. THE SPEAKER WIRES CAN BE INTERCHANGED IF NECESSARY.3. MUS

22、T USE VIDEO SWITCHING THROUGH TV TO ACCESSCOMPONENT VIDEO. GrayGreenRedWhiteBrownBlueComposite Video cable not included DVD600II DVD600II 7DVD600IIFront Panel ControlsMain Power Switch: Press this buttonto apply power to the DVD600II. When theswitch is pressed in, the unit is placed in aStandby mode

23、, as indicated by the amberPower Indicatorsurrounding theSystem Power Control. This buttonMUST be pressed in to operate the unit. Toturn the unit off and prevent the use of theremote control, this switch should be presseduntil it pops out from the front panel so thatthe word “OFF” may be read at the

24、 top of theswitch.NOTE: This switch is normally left in the “ON”position.System Power Control: When theMain Power Switchis “ON,” pressthis button to turn on the DVD600II; press itagain to turn the unit off. Note that the PowerIndicatorin the center of the switchwill turn green when the unit is on.Po

25、wer Indicator: This LED will be illu-minated in amber when the unit is in theStandby mode to signal that the unit is readyto be turned on. When the unit is in operation,the indicator will turn green.Disc Tray: Holds up to five DVD or CDdiscs that can be played one at a time in theDVD600II.Disc Skip:

26、 Press twice in quick succes-sion to change the disc being played. This willmove the tray forward to the next occupiedposition, skipping over the empty-disc positions.Search Forward/Reverse: Press tomove forward or backward through a disc atone of four speeds. Each press and release willincrease the

27、 search speed, as indicated in theon-screen display. Once you have selected thedesired speed, release the button and the discwill continue to search at fast speed. Toresume normal playback speed, press the Play Button .Open/Close Button: Press to open orclose the Disc Tray . Upon closing thedisc tra

28、y, the On Screen Library system willbegin to identify all loaded discs.Skip Forward/Reverse: Press to moveforward or backward through the music tracksor chapters on a disc.Stop: Press once to place the disc in theResume mode, which means that playback willstop, but (as long as the tray is not opened

29、 orthe disc changed) DVD playback will continuefrom the same point on the disc when the Playbutton is pressed again. Resume will also workif the unit was turned off. To stop a disc andhave play start from the beginning, press thebutton twice.Play/Pause: Press to begin playback ofa disc, or to moment

30、arily pause playback. If aDVD is playing, action will freeze and a stillpicture will be displayed when the button ispressed. Direct Access Buttons: Press one ofthese buttons to play any of the five discsloaded in the Disc Tray.Information Display: This display con-tains a variety of indicators that

31、provide infor-mation about the status of the DVD600IIandthe disc currently playing.Display Dim: Press this button to adjustthe brightness of the Information Display by50% or to turn the display off completely in thefollowing order: FULL BRIGHTNESS HALFBRIGHTNESS OFF FULL BRIGHTNESS.Remote Sensor: Th

32、e sensor thatreceives the infrared commands from theremote control is behind this area. Do notcover or obscure this part of the front panel, inorder to avoid a malfunction with the remote.96KHz 24bit DVD600II DVD600II 8DVD600IIFront Panel Information Display Disc Type: Lights to show the type of dis

33、ccurrently being played.Disc Number: Shows if a disc is loadedin a tray position. The indicator for the disc inplay flashes. Note that if a disc is added to orremoved from the tray while a disc is playing,the indicator will not show the change until alldiscs are cycled. Title: Shows the DVD title nu

34、mber currentlyplaying.Chapter/Track Number: Shows the current chapter (DVD) or current track number (CD).Program Time: Shows the running timeof a DVD; current track time; time remainingin the current track; or the total remaining timeof a CD. NOTE: The Program Time Indicators will alsodisplay text m

35、essages about the DVD600IIsstatus, including Reading when a disc isloading, Bye when the unit is turned off, andDisc Error when a disc not compatiblewith the DVD600IIis put into the play position. Intro: Lights when the IntroScan functionis active.Program: Lights during programming.Repeat: Lights to

36、 indicate any of theRepeat modes.Random: Lights when the unit is in theRandom Play mode.Resume: Lights when the Stop button hasbeen pressed once to put the unit in theResume mode.Playback Mode: Lights to show the cur-rent playback mode: Lights when a disc is playing in the Normalmode. Lights when th

37、e disc is in the Fast SearchForward mode. For DVDs, when both trianglesglow steadily, the disc plays at 2x normalspeed. When the right triangle is flashing, thedisc plays at 4x normal speed. When the lefttriangle is flashing, the disc plays at 8x normalspeed. When both triangles are flashing, thedis

38、c plays at 16x normal speed. For CDs, onlythe first three Fast Search modes are available. Lights when the disc is paused. Lights when the disc is in the Fast SearchReverse mode. For DVDs, when both trianglesglow steadily, the disc plays at 2x normalspeed. When the left triangle is flashing, thedisc

39、 plays at 4x normal speed. When the righttriangle is playing, the disc plays at 8x normalspeed. When both triangles are flashing, thedisc plays at 16x normal speed. For CDs, onlythe first three Fast Search modes are available.Parental Lock Indicator: This indicatorlights when the parental-lock syste

40、m isengaged in order to prevent anyone fromchanging the rating level without a code.96kHz/24-Bit Indicator: When a high-resolution, linear PCM bitstream with a sam-pling rate of 96kHz/24 bits is detected, thisindicator will light. Such a selection may befound as an alternative audio track on a DVD-A

41、udio disc.M96KHz 24bit DVD600II DVD600II 9Component Video Outputs: If your TV orvideo projector has component video inputs,you may connect these output jacks to the setfor the highest video quality available. Notethat the component video inputs may belabeled as Y/Pr/Pb or Y/Cr/Cb but, for connec-tio

42、n purposes, they are the same. The outputsof these jacks should NOT be connected to astandard composite video input.S-Video Output: Connect this jack to theS-Video input on a television or video projector,or to an S-Video input on an A/V receiver orprocessor if you are using that type of devicefor S

43、-Video input switching.Composite Video Output: Connect thisjack to the video input on a television or videoprojector, or to a video input on an A/V receiveror processor if you are using that type ofdevice for video input switching.Coaxial Digital Output: Connect this jackto the coaxial digital input

44、 of an A/V receiveror surround processor for Dolby Digital, DTS orPCM audio playback. NOTE: The coaxial digital output should onlybe connected to a digital input. Even though itis the same RCA-type connector as standardanalog audio connections, DO NOT connect itto a conventional analog input jack.Re

45、mote Control Output: Connect thisjack to the infrared (IR) input jack of anotherJBL (or other compatible) remote-controlledproduct to have the built-in Remote Sensoron the DVD600IIprovide IR signals toother compatible products.Remote Control Input: Connect the out-put of a remote infrared sensor, or

46、 the remotecontrol output of another JBL (or other compat-ible) product, to this jack. This will enable theremote control to operate even when the frontpanel Remote Sensor is blocked. Thisjack may also be used with compatible IRremote control-based automation systems.AC Power Cord: Connect this plug

47、 to an AC outlet. If the outlet is controlled by aswitch, make certain that it is in the ON position.DVD600IIRear Panel Connections DVD600II DVD600II 10Remote Control FunctionsIMPORTANT NOTE: The remote control forthe JBL Cinema ProPack 600IImay be pro-grammed to control up to eight devices, includ-

48、ing the DCR600IIand DVD600II. It is helpful tothink of the remote as being organized into“pages,” with one page for each device.Depending on which device has been selected,the buttons on that devices page will performdifferent functions, as listed starting on thispage. These functions may vary from

49、the labelson the remote, and from one device to thenext. Some buttons may perform no functionat all for a given device.In order to go to the page for a particulardevice, such as the DVD600II, you will need topress the Input Selector button for that device(DVD in this case), located in a grouping jus

50、tbelow the power buttons. The remote will thenfunction as if it were dedicated to the DVD600II.If you would like to make an adjustment thataffects the DCR600IIreceiver, such as turningthe volume up or down, you must first go tothe page for the DCR600IIby pressing its InputSelector button. This butto