Yamaha-DVDS830-dvd-sm 维修电路原理图.pdf

《Yamaha-DVDS830-dvd-sm 维修电路原理图.pdf》由会员分享，可在线阅读，更多相关《Yamaha-DVDS830-dvd-sm 维修电路原理图.pdf（104页珍藏版）》请在收音机爱好者资料库上搜索。

1、DVD-S830100825P.O.Box 1, Hamamatsu, JapanI CONTENTSTO SERVICE PERSONNEL . 2PREVENTION OF ELECTRO STATIC DISCHARGE.34LOCALE MANAGEMENT INFORMATION . 4FRONT PANELS. 4REAR PANELS . 5REMOTE CONTROL PANEL . 5SPECIFICATIONS. 6DISASSEMBLY PROCEDURES ANDSERVICE POSITION. 711OPTICAL PICKUP SELF-DIAGNOSIS AND

2、REPLACEMENT PROCEDURE . 1213SELF-DIAGNOSIS FUNCTION ANDSERVICE MODES. 1419ASSEMBLING AND DISASSEMBLING THEMECHANISM UNIT .2028ADJUSTMENT . 2930BLOCK DIAGRAM. 3139INTERCONNECTION SCHEMATIC DIAGRAM. 40ABBREVIATIONS . 41PRINTED CIRCUIT BOARD . 4253SCHEMATIC DIAGRAM . 5482VOLTAGE CHART. 8394PARTS LIST.

3、95102Parts List for Chip Carbon Resistors . 103Parts List for Carbon Resistors . 104SERVICE MANUALDVD PLAYERDVD-S830IMPORTANT NOTICEThis manual has been provided for the use of authorized YAMAHA Retailers and their service personnel.It has been assumed that basic service procedures inherent to the i

4、ndustry, and more specifically YAMAHA Products, are alreadyknown and understood by the users, and have therefore not been restated.WARNING:Failure to follow appropriate service and safety procedures when servicing this product may result in personalinjury, destruction of expensive components, and fa

5、ilure of the product to perform as specified. For these reasons,we advise all YAMAHA product owners that any service required should be performed by an authorizedYAMAHA Retailer or the appointed service representative.IMPORTANT:The presentation or sale of this manual to any individual or firm does n

6、ot constitute authorization, certification orrecognition of any applicable technical capabilities, or establish a principle-agent relationship of any form.The data provided is believed to be accurate and applicable to the unit(s) indicated on the cover. The research, engineering, andservice departme

7、nts of YAMAHA are continually striving to improve YAMAHA products. Modifications are, therefore, inevitableand specifications are subject to change without notice or obligation to retrofit. Should any discrepancy appear to exist, pleasecontact the distributors Service Division.WARNING:Static dischar

8、ges can destroy expensive components. Discharge any static electricity your body may haveaccumulated by grounding yourself to the ground buss in the unit (heavy gauge black wires connect to this buss).IMPORTANT:Turn the unit OFF during disassembly and part replacement. Recheck all work before you ap

9、ply power to the unit.RadioFans.CN 收音机爱 好者资料库DVD-S8302DVD-S830WALLOUTLETEQUIPMENTUNDER TESTAC LEAKAGETESTER OREQUIVALENTINSULATINGTABLEWARNING: CHEMICAL CONTENT NOTICE!The solder used in the production of this product contains LEAD. In addition, other electrical/electronic and/or plastic (whereappli

10、cable) components may also contain traces of chemicals found by the California Health and Welfare Agency (andpossibly other entities) to cause cancer and/or birth defects or other reproductive harm.DO NOT PLACE SOLDER, ELECTRICAL/ELECTRONIC OR PLASTIC COMPONENTS IN YOUR MOUTH FOR ANY REA-SON WHATSOE

11、VER!Avoid prolonged, unprotected contact between solder and your skin! When soldering, do not inhale solder fumes or exposeeyes to solder/flux vapor!If you come in contact with solder or components located inside the enclosure of this product, wash your hands beforehandling food.WARNING: Laser Safet

12、yThis product contains a laser beam component. This component may emit invisible, as well as visible radiation, which maycause eye damage. To protect your eyes and skin from laser radiation, the following precautions must be used duringservicing of the unit.1) When testing and/or repairing any compo

13、nent within the product, keep your eyes and skin more than 30 cm away fromthe laser pick-up unit at all times. Do not stare at the laser beam at any time.2) Do not attempt to readjust, disassemble or repair the laser pick-up, unless noted elsewhere in this manual.3) CAUTION : Use of controls, adjust

14、ments or performance of procedures other than those specified herein may result inhazardous radiation exposure.Laser Emitting conditions:1) When the Top Cover is removed, and the STANDBY/ON SW is turned to the ON position, the laser component willemit a beam for several seconds to detect if a disc i

15、s present. During this time (5-10 sec.) the laser may radiate throughthe lens of the laser pick-up unit. Do not attempt any servicing during this period!If no disc is detected, the laser will stop emitting the beam. When a disc is set, you will not be exposed to any laseremissions.2) The laser power

16、 level can be adjusted with the VR on the pick-up PWB. However, this level has been set by the factoryprior to shipping from the factory. Do not adjust this laser level control unless instruction is provided elsewhere in thismanual.Adjustment of this control can increase the laser emission level fro

17、m the device.Laser Diode PropertiesType:Semiconductor laser GaAlAsWave length:658 nm (DVD)790 nm (VCD/CD)Output Power: CLASS IIa 1mW (DVD)CLASS I1mW (VCD/CD)I TO SERVICE PERSONNEL1. Critical Components InformationComponents having special characteristics are marked sand must be replaced with parts h

18、aving specifications equalto those originally installed.2. Leakage Current Measurement (For 120V Models Only)When service has been completed, it is imperative to verifythat all exposed conductive surfaces are properly insulatedfrom supply circuits.GMeter impedance should be equivalent to 1500 ohm sh

19、untedby 0.15F.GLeakage current must not exceed 0.5mA.GBe sure to test for leakage with the AC plug in both polarities.RadioFans.CN 收音机爱 好者资料库DVD-S8303DVD-S830VARO!:AVATTAESSA JA SUOJALUKITUS OHITETTAESSA OLET ALTTIINA NKYMTTMLLE LASER-STEILYLLE. L KATSO STEESEEN.VARNING!:OSYNLIG LASERSTRLNING NR DEN

20、NA DEL R PPNAD OCH SPRREN R URKOPPLAD.BETRAKTA EJ STRLEN.WARNINGThe use of optical instruments with this product will increase eye hazard.Repair handling should take place as much as possible with a disc loaded inside the playerB, G modelsA, R modelsI PREVENTION OF ELECTRO STATIC DISCHARGEThe laser

21、diode in the traverse unit (optical pickup) may be damaged due to static electricity from clothes or the human body.Use caution to prevent electrostatic damage when servicing or handling the laser diode.1. Grounding for Electrostatic Damage PreventionSome devices, such as the DVD player, use an opti

22、cal pickup (laser diode) that will be damaged by static electricity in theworking environment. Only attempt service after ensuring that all grounding procedures have been completed.1. Worktable groundingPut a grounded conductive material (sheet) or iron sheet on the area where the optical pickup is

23、placed.2. Human body groundingUse an anti-static wrist strap to discharge the static electricity from your body.1MConductive material(sheet) or iron sheetAnti-static wrist strapDVD-S8304DVD-S830I FRONT PANELS2. Handling of the Optical Pickup1. To prevent damage to the optical pickup replacement part

24、s during transportation and before installation, both ends of thelaser diode are short-circuited. After installing the new part, remove the short circuit according to the correct procedure inthis service manual.2. Do not use a tester to check the laser diode in the optical pickup. The power supply i

25、n the tester will damage the laserdiode.3. Handling Precautions for the Traverse Unit (Optical Pickup)1. Handle the traverse unit (optical pickup) gently, as it is an extremely high-precision assembly.2. The flexible cable lines may break if an excessive force is applied to it. Use caution when hand

26、ling the cable.3. The semi-fixed resistor for laser power adjustment should not be adjusted. Do not turn the resistor.12425542635I LOCALE MANAGEMENT INFORMATIONLocale Management Information : This DVD player is designed and manufactured to respond to the Locale ManagementInformation that is recorded

27、 on the DVD disc. If the Locale number described on the DVD disc does not correspond to theLocale number of this DVD player, this DVD player cannot play this disc.This product incorporates copyright protectiontechnology that is protected by method claims ofcertain U.S. patents and other intellectual

28、property rights owned by Macrovision Corporationand other rights owners. Use of this copyrightprotection technology must be authorized byMacrovision Corporation, and is intended forhome and other limited viewing uses only unlessotherwise authorized by Macrovision Corporation.Reverse engineering or d

29、isassembly is prohibited.DVD-S830 (A, R models)DVD-S830 (B, G models)DVD-S8305DVD-S830DVD-S830 (A model)DVD-S830 (B, G models)I REAR PANELSDVD-S830 (R model)I REMOTE CONTROL PANELZOOMSET UPON SCREENRETURNTOP MENUMENUENTERPAUSESTOPSKIPPLAYSLOW/SEARCHOPEN/CLOSEPOWERCINEMASUB TITLEPROGA-BREPEATRANDOMCA

30、NCELV.S.S.V975640AUDIOANGLEGROUPPAGEVIDEO OFFPOS. MEMO.DVD-S8306DVD-S830G DIMENSIONS435 (17-1/8)60(2-3/8)258 (10-1/8)Unit : mm (inch)単位: mm （）I SPECIFICATIONSSignal System:PAL 625/50, PAL525/60, NTSCOperating Temperature Range: +5 to +35COperating Humidity Range:5 to 90 % RH (no condensation)Discs P

31、layed 8 cm or 12 cm:(1) DVD-Audio(2) DVD-Video(3) DVD+RW/DVD+R(4) DVD-R/DVD-RW (DVD-Video compatible)(5) CD-Audio (CD-DA)(6) Video CD(7) CD-R/CD-RW (CD-DA, Video-CD formatted discs)(8) MP3Maximum Number of Tracks and Groups Recognizable:999 tracks and 99 groupsCompatible Compression Rate:between 32

32、kbps and 320 kbpsVideo Output:Output Level:1 Vp-p (75 )Output Terminal:Pin jack (1 system)S Video Output:Y Output Level:1 Vp-p (75 )C Output Level:NTSC;0.286 Vp-p (75 )PAL;0.300 Vp-p (75 )Output Terminal:S terminal (1 system)RGB Video Output B, G models:R Output Level:0.7 Vp-p (75 )G Output Level:0.

33、7 Vp-p (75 )B Output Level:0.7 Vp-p (75 )Output Connector:SCARTComponent Video Output A, R models:(NTSC: 480P/480I, PAL: 576I)Y Output Level:1 Vp-p (75 )PB Output Level:0.7 Vp-p (75 )PR Output Level:0.7 Vp-p (75 )Output Connector:Pin jack(Y: green, PB : blue, PR : red)Number of Connectors: 1 systemA

34、udio Output:Output Level:2 Vrms (1 kHz, 0 dB)Output Connector:Pin jackNumber of Connectors:2 Channel:1 system5.1-channel Discrete Output (5.1 Channel): 1 systemAudio Performance:(1) Frequency Response:DVD (linear audio): 2 Hz22 kHz (48 kHz sampling)2 Hz44 kHz (96 kHz sampling)DVD-Audio:2 Hz88 kHz (1

35、92 kHz sampling)CD audio:2 Hz 20 kHz(2) S/N Ratio:CD audio:115 dB(3) Dynamic Range:DVD (linear audio): 102 dBCD audio:98 dB(4) Total Harmonic Distortion:CD audio:0.0025 %Digital Audio Output:Optical Digital Output:Optical terminalCoaxial Digital Output: Pin jackPickup: Wave Length:658 nm/790 nmLaser

36、 power:CLASS 2/CLASS 1Power Supply:A, B, G models:AC 220240 V, 50 HzR model:AC 110240 V, 50/60 HzPower Consumption:A, B, G models:15 WR model:16 WStandby Power Consumption: approx. 4 WDimensions (W x H x D): 435 x 60 x 258 mm(17-1/8 x 2-3/8 x 10-1/8)Weight:3.3 kg (7 lbs. 4 oz.)Finish:Gold color:R mo

37、delBlack color:A, B, G modelsTitanium color:B, G modelsAccessories:Remote Control, Batteries, Audio/Video Cable, PowerCable* Specifications are subject to change without notice dueto product improvements.A . Australian modelB. British modelG. European modelR . General modelManufactured under license

38、 from Dolby Laboratories.“Dolby”, “Pro Logic” and the double-D symbol are trademarks ofDolby Laboratories.“DTS” and “DTS Digital Surround” are registered trademarks ofDigital Theater Systems, Inc.DVD-S8307DVD-S830I DISASSEMBLY PROCEDURES AND SERVICE POSITION (Remove parts in the order as numbered.)D

39、isconnect the power cable from the AC outlet.1. Disassembly Procedure2. Casing Parts and P.C.B. LocationsRear PanelMODULE P.C.B.TrayMechanism UnitTop CoverFRONT 1 P.C.B. / FRONT 2 P.C.B.TERMINAL P.C.B. / POWER P.C.B.SCART P.C.B.(B, G models)Front PanelINTERMEDIATE P.C.B.Mechanism UnitINTERMEDIATE P.

40、C.B.SCART P.C.B. (B, G models)TERMINAL P.C.B.MODULE P.C.B.FRONT 2 P.C.B.Front PanelFRONT 1 P.C.B.POWER P.C.B.Top CoverDVD-S8308DVD-S8303. Top CoverRemove the screws.4. Tray1. Remove the gear for opening the tray from the mechanismunit and install it onto a screwdriver to make a gear jig.2. Insert th

41、e gear jig into the tray open/close hole.3. Turn the gear jig counterclockwise to open the tray.4. Remove the tray lid from the tray section.MechanismUnitGear for opening the trayCutGearScrewdriverDVD-S8309DVD-S8302. Release the tabs.3. Remove the connectors.6. Mechanism Unit1. Remove the screws.2.

42、Remove the connectors.3. Pull out the mechanism unit vertically.5. Front Panel1. Remove the screws.ScrewFront panel7. INTERMEDIATE P.C.B.1. Remove the screws.2. Remove the solders.3. Remove the connectors.DVD-S83010DVD-S83010. Rear Panel1. Remove the screws.2. Release the tabs.9. FRONT 1 P.C.B. and

43、FRONT 2 P.C.B.1. Remove the screws (A).2. Remove the Front Angle.8. MODULE P.C.B.1. Remove the screws.2. Remove the connectors.3. Squeeze each tab with pliers to pull out the MODULEP.C.B. vertically.3. Remove the screws (B).11. SCART P.C.B. (B, G models)1. Remove the connectors.2. Squeeze each tab w

44、ith pliers to pull out the SCARTP.C.B. vertically.12. TERMINAL and POWER P.C.B.1. Remove the connectors2. Remove the screws.3. Remove the FC1001A Solder.DVD-S83011DVD-S8301TX94637026 pinsPS4201 (MODULE P.C.B.) PP4301 (TERMINAL P.C.B.)JGS00982AAX1661022 pinsPS3201 (MODULE P.C.B.) PP3201 (TERMINAL P.C

45、.B.)JGS011613.2. Servicing position of the INTERMEDIATE P.C.B.13. Servicing Position13.1. Servicing position of the MODULE P.C.B.13.3. List of the Extension CablesSCART P.C.B.(B, G models)SCART P.C.B.(B, G models)DVD-S83012DVD-S830I OPTICAL PICKUP SELF-DIAGNOSIS AND REPLACEMENT PROCEDURE1. Self-diag

46、nosisAn optical pickup self-diagnosis function and tilt adjustment check function have been included in this unit. When repairing,use the following procedure for effective Self-diagnosis and tilt adjustment. Be sure to use the self-diagnosis function beforereplacing the optical pickup when NO DISC i

47、s displayed. As a guideline, you should replace the optical pickup when thevalue of the CD laser drive current is more than 55 (70 for DVD).Note:Press the STANDBY/ON button to turn on the power. Check the value within three minutes before the unit warms up.(Otherwise, the result will be incorrect.)D

48、VD-S83013DVD-S8302.Cautions to Be Used Before Replacing the Optical Pickup Unit and Spindle Motor AssemblyBefore replacing the optical pickup unit and spindle motor assembly, check the total usage hours for each of them. Thechecking method is as follows:Note: Each of these procedures should start wi

49、th the unit stopped.Cautions to be taken when replacing the opticalpickupThe optical pickup may become damaged due to staticelectricity from the human body. Take proper protectionmeasures against static electricity before repairing theparts around the optical pickup. (See the page describingthe PREV

50、ENTION OF ELECTRO STATIC DISCHARGE.)1. Do not touch the areas around the laser diode andactuator.2. Do not judge the laser diode with a tester. (The testerwill damage the diode.)3. It is recommended to use an anti-static solderingiron for soldering or desoldering on the pickup.(Recommended soldering