Yamaha-CDS2000-cd-sm2 维修电路原理图.pdf

《Yamaha-CDS2000-cd-sm2 维修电路原理图.pdf》由会员分享，可在线阅读，更多相关《Yamaha-CDS2000-cd-sm2 维修电路原理图.pdf（59页珍藏版）》请在收音机爱好者资料库上搜索。

1、I CONTENTSTO SERVICE PERSONNEL . 23PREVENTION OF ELECTROSTATIC DISCHARGE . 4FRONT PANEL . 5REAR PANELS . 57REMOTE CONTROL PANEL . 8SPECIFICATIONS / 参考仕様. 89INTERNAL VIEW . 9DISASSEMBLY PROCEDURES / 分解手順. 1016TEST MODE / . 17UPDATING FIRMWARE / 書込. 1824DISPLAY DATA . 25IC DATA . 2628PIN CONNECTION DI

2、AGRAMS. 2930BLOCK DIAGRAM. 31PRINTED CIRCUIT BOARDS. 3240SCHEMATIC DIAGRAMS. 4145REPLACEMENT PARTS LIST . 4758REMOTE CONTROL. 59101078SERVICE MANUALSUPER AUDIO CD PLAYER 2007 All rights reserved.This manual is copyrighted by YAMAHA and may not be copied orredistributed either in print or electronica

3、lly without permission.P.O.Box 1, Hamamatsu, Japan 07.12IMPORTANT NOTICEThis manual has been provided for the use of authorized YAMAHA Retailers and their service personnel.It has been assumed that basic service procedures inherent to the industry, and more specifically YAMAHA Products, are alreadyk

4、nown and understood by the users, and have therefore not been restated.WARNING:Failure to follow appropriate service and safety procedures when servicing this product may result in personalinjury, destruction of expensive components, and failure of the product to perform as specified. For these reas

5、ons,we advise all YAMAHA product owners that any service required should be performed by an authorizedYAMAHA Retailer or the appointed service representative.IMPORTANT:The presentation or sale of this manual to any individual or firm does not constitute authorization, certification orrecognition of

6、any applicable technical capabilities, or establish a principle-agent relationship of any form.The data provided is believed to be accurate and applicable to the unit(s) indicated on the cover. The research, engineering, andservice departments of YAMAHA are continually striving to improve YAMAHA pro

7、ducts. Modifications are, therefore, inevitableand specifications are subject to change without notice or obligation to retrofit. Should any discrepancy appear to exist, pleasecontact the distributors Service Division.WARNING:Static discharges can destroy expensive components. Discharge any static e

8、lectricity your body may haveaccumulated by grounding yourself to the ground buss in the unit (heavy gauge black wires connect to this buss).IMPORTANT:Turn the unit OFF during disassembly and part replacement. Recheck all work before you apply power to the unit.CD-S2000CD-S2000RadioFans.CN 收音机爱 好者资料

9、库2CD-S2000CD-S2000WALLOUTLETEQUIPMENTUNDER TESTAC LEAKAGETESTER OREQUIVALENTINSULATINGTABLEWARNING: CHEMICAL CONTENT NOTICE!This product contains chemicals known to the State of California to cause cancer, or birth defects or other reproductiveharm.DO NOT PLACE SOLDER, ELECTRICAL/ELECTRONIC OR PLAST

10、IC COMPONENTS IN YOUR MOUTH FOR ANYREASON WHAT SO EVER!Avoid prolonged, unprotected contact between solder and your skin! When soldering, do not inhale solder fumes or exposeeyes to solder/flux vapor!If you come in contact with solder or components located inside the enclosure of this product, wash

11、your hands beforehandling food.1. Critical Components InformationComponents having special characteristics are marked sand must be replaced with parts having specifications equalto those originally installed.2. Leakage Current Measurement (For 120V Models Only)When service has been completed, it is

12、imperative to verifythat all exposed conductive surfaces are properly insulatedfrom supply circuits.GMeter impedance should be equivalent to 1500 ohms shuntedby 0.15F.GLeakage current must not exceed 0.5mA.GBe sure to test for leakage with the AC plug in both polarities.本機搭載基板付接合部無鉛付。無鉛種類、修理時下記無鉛使用推

13、奨。 Sn+Ag+Cu （錫+銀+銅） Sn+Cu （錫+銅） Sn+Zn+Bi （錫+亜鉛+）注意：無鉛融点温度通常鉛入比3040程度高、合使用。All of the P.C.B.s installed in this unit and solder joints aresoldered using the lead free solder.Among some types of lead free solder currently available,it is recommended to use one of the following types for therepair work

14、.Sn + Ag + Cu (tin + silver + copper)Sn + Cu (tin + copper)Sn + Zn + Bi (tin + zinc + bismuth)Caution:As the melting point temperature of the lead free solder isabout 30C to 40C (50F to 70F) higher than that of the leadsolder, be sure to use a soldering iron suitable to each solder.About lead free s

15、older / 無鉛I TO SERVICE PERSONNELWARNING: Laser SafetyThis product contains a laser beam component. This component may emit invisible, as well as visible radiation,which may cause eye damage. To protect your eyes and skin from laser radiation, the following precautions must beused during servicing of

16、 the unit.1) When testing and/or repairing any component within the product, keep your eyes and skin more than 30 cm away fromthe laser pick-up unit at all times. Do not stare at the laser beam at any time.2) Do not attempt to readjust, disassemble or repair the laser pick-up, unless noted elsewhere

17、 in this manual.3) CAUTION : Use of controls, adjustments or performance of procedures other than those specified herein may result inhazardous radiation exposure.Laser Emitting conditions:1) When the top cover is removed, and the STANDBY/ON SW is turned to the “ON” position, the laser component wil

18、l emita beam for several seconds to detect if a disc is present. During this time (5-10 sec.) the laser may radiate through thelens of the laser pick-up unit. Do not attempt any servicing during this period!If no disc is detected, the laser will stop emitting the beam. When a disc is loaded, you wil

19、l not be exposed to any laseremissions.2) The laser power level can be adjusted with the VR on the pick-up PWB, however, this level has been set by the factoryprior to shipping from the factory. Do not adjust this laser level control unless instruction is provided elsewhere in thismanual. Adjustment

20、 of this control can increase the laser emission level from the device.RadioFans.CN 收音机爱 好者资料库3CD-S2000CD-S2000Material:SA-CDSemiconductor laser (AlGaInP)CDSemiconductor laser (AlGaAs)Wavelength:SA-CD650 nmCD780 nmWarning for power supplyThe primary side of the power supply carries live mains voltag

21、e when the player is connected to the mains even whenthe player is switched off !This primary area is not shielded so it is possible to touch copper tracks and/or components when servicing the player.Service personnel have to take precautions to prevent touching this area or components in this area.

22、Note:The screws on the DVD mechanism may never be touched, removed or re-adjusted.Handle the DVD mechanism with care when the unit has to be exchanged!The DVD mechanism is very sensitive for dropping or giving shocks.Laser Diode PropertiesLaser Output:SA-CD5 mW (max.)CD7 mW (max.)B, G models4CD-S200

23、0CD-S2000I PREVENTION OF ELECTROSTATIC DISCHARGESome semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are calledElectrostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field-effect transis-tors

24、 and semiconductor “chip” components. The following techniques should be used to help reduce the incidence of compo-nent damage caused by electro static discharge (ESD).1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any ESD onyour body by tou

25、ching a known earth ground. Alternatively, obtain and wear a commercially available discharging ESD wriststrap, which should be removed for potential shock reasons prior to applying power to the unit under test.2. After removing an electrical assembly equipped with ES devices, place the assembly on

26、a conductive surface such asaluminum foil, to prevent electrostatic charge buildup or exposure of the assembly.3. Use only a grounded-tip soldering iron to solder or unsolder ES devices.4. Use only an anti-static solder removal device. Some solder removal devices not classified as “anti-static (ESD

27、protected)”can generate electrical charge sufficient to damage ES devices.5. Do not use freon-propelled chemicals. These can generate electrical charges sufficient to damage ES devices.6. Do not remove a replacement ES device from its protective package until immediately before you are ready to inst

28、all it. (Mostreplacement ES devices are packaged with leads electrically shorted together by conductive foam, aluminum foil or compa-rable conductive material).7. Immediately before removing the protective material from the leads of a replacement ES divice, touch the protective mate-rial to the chas

29、sis or circuit assembly into which the device will be installed.CAUTION: Be sure no power is applied to the chassis or circuit, and observe all other safety precautions.8. Minimize bodily motions when handling unpackaged replacement ES devices. (Otherwise harmless motion such as brush-ing together o

30、f your fabric clothes or lifting of your foot from a carpeted floor can generate static electricity (ESD) sufficientto damage an ES device).Grounding for electrostatic breakdown prevention1. Human body grounding.Use the antistatic wrist strap to discharge the static electricity from your body.2. Wor

31、k table grounding.Put a conductive material (sheet) or steel sheet on the area where the optical pickup is placed and ground the sheet.Caution:The static electricity of your clothes will not be grounded through the wrist strap. So take care not to let your clothes touch theoptical pickup.1M-ohmsCond

32、uctive material(sheet) or steel sheetAnti-static wrist strap5CD-S2000CD-S2000I FRONT PANELCD-S2000 (U, C, R, T, K, A, B, G, L, J models)I REAR PANELSCD-S2000 (U, C models)CD-S2000 (R model)6CD-S2000CD-S2000CD-S2000 (T model)CD-S2000 (K model)CD-S2000 (A model)7CD-S2000CD-S2000CD-S2000 (B, G models)C

33、D-S2000 (L model)CD-S2000 (J model)8CD-S2000CD-S2000I Audio Section / 部Frequency Response / 周波数特性SA-CD . 2 Hz to 50 kHz (-3 dB)CD .2 Hz to 20 kHzTotal Harmonic Distortion + Noise (1 kHz) / 高調波歪率 （1 kHz）SA-CD . 0.0017 % or lessCD .0.002 % or lessSignal to Noise Ratio / 信号対雑音比 (IHF-A Network).116 dB o

34、r moreDynamic Range / SA-CD .110 dB or moreCD .100 dB or moreOutput Voltage (1 kHz, 0 dB) / 出力電圧 （1 kHz、0 dB）. 2.0 0.3 VI General / 総合Power Supply / 電源電圧U, C models .AC 120 V, 60 HzR, L models .AC 110/120/220/230-240 V, 50/60 HzT model.AC 220 V, 50 HzK model.AC 220 V, 60 HzA model.AC 240 V, 50 HzB,

35、G models .AC 230 V, 50 HzJ model . AC 100 V, 50/60 HzPower Consumption / 消費電力U, C, R, T, K, A, B, G, L models . 30 WJ model . 25 WOff-state Power Consumption / OFF時消費電力. 0 WDimensions (W x H x D) / 寸法 （幅高奥行）. 435 x 137 x 440 mm (17-1/8” x 5-3/8” x 17-5/16”)Weight / 質量. 15 kg (33 lbs. 1 oz.)Finish /

36、仕上Black color . U, C, R, T, K, A, B, G, L, J modelsSilver color . U, C, R, T, K, A, B, G, L, J modelsAccessories / 付属品Remote control x 1, Battery (R6, AA, UM-3) x 2, Audio pin cable (1.5 m)x 1, Power cable (2 m) x 1*Specifications are subject to change without notice due to productimprovements. 参考仕様

37、外観予告変更。I SPECIFICATIONS / 参考仕様U . U.S.A. modelC . Canadian modelR . General modelT . Chinese modelK . Korean modelA . Australian modelB . British modelG . European modelL . Singapore modelJ. Japanese modelI REMOTE CONTROL PANELCDX59CD-S2000CD-S2000435 (17-1/8)137 (5-3/8)440 (17-5/16)418 (16-7/16)120

38、 (4-3/4)8(5/16)14(9/16)17(11/16)DIMENSIONS / 寸法図Unit: mm (inch)単位：mm （）I INTERNAL VIEW1 POWER TRANSFORMER for DIGITAL/ LOADER2 POWER TRANSFORMER for AUDIO3 POWER (2) P.C.B. (R, L models)4 POWER (1) P.C.B.5 LOADER ASSY6 AUDIO P.C.B.7 DIGITAL (1) P.C.B.8 DIGITAL (5) P.C.B.9 POWER (3) P.C.B.0 DIGITAL (

39、4) P.C.B.A DIGITAL (3) P.C.B.B DIGITAL (2) P.C.B.2345678B90A110CD-S2000CD-S2000I DISASSEMBLY PROCEDURES / 分解手順Fig. 1(Remove parts in the order as numbered.)Disconnect the power cable from the AC outlet.1. Removal of Panel Side L/Ra. Remove 2 screws (1), coned disc spring L and washerside. (Fig. 1)b.

40、 Lift the panel side L a little, release hooks at 3 locationsand then remove the panel side L. (Fig. 1)c. Remove 2 screws (2) and then remove 2 washers.(Fig. 1)d. Lift the panel side R a little, release hooks at 3 loca-tions and remove the panel side R. (Fig. 1)2. Removal of Top Covera. Remove 7 scr

41、ews (3), 2 screws (4) and 2 screws(5). (Fig. 1)b. Remove the top cover. (Fig. 1)（番号順部品取外。）AC電源、電源抜。1. L/R外方a. 12本、L、外。 （Fig. 1）b. L少持上、3所外、L取外。 （Fig. 1）c. 22本外、2個外。 （Fig. 1）d. R少持上、3所外、R取外。 （Fig. 1）2. 外方a. 37本、42本、52本外。（Fig. 1）b. 取外。 （Fig. 1）Panel side L LPanel side R RWasher sideWasher sideConed di

42、sc spring LLConed disc spring LLFront panelTop cover767313452HookHookPOWER ON / OFF switch“POWER ON / OFF” HookLid11CD-S2000CD-S2000Fig. 23. 外方a. 底面下図矢印方向動。 （Fig. 2） 、押出。b. 後方押、押出。 （Fig. 3）c. 62本外、取外。 （Fig. 1）d. 前方押、閉。e. 78本外。 （Fig. 1）f. “POWER ON/OFF” ON。g. “POWER ON/OFF” 傷前方取外。 （Fig. 1）Fig. 33. Re

43、moval of Front Panela. Using a flatblade screwdriver, move the slider at the bot-tom in the direction of the arrow shown below. (Fig. 2)*At this time, the tray is not pushed out.b. Push out the tray by pushing its rear. (Fig. 3)c. Remove 2 screws (6) and then remove the lid. (Fig. 1)d. Close the tra

44、y by pushing its front.e. Remove 8 screws (7). (Fig. 1)f.Set the “POWER ON/OFF” switch to the ON position.g. Remove the front panel forward gradually, using carenot to cause any damage to the “POWER ON/OFF”switch. (Fig. 1)Flatblade screwdriver Tray12CD-S2000CD-S20004. ASSY外方a. 84本、92本外、取外。 （Fig. 4）b

45、. 09本外。 （Fig. 4）c. CB601、CB902外。 （Fig. 4）d. ASSY取外。 （Fig. 4）5. AUDIO P.C.B.外方a. A6本外。 （Fig. 4）b. B4本、C4本外。 （Fig. 5）c. CB1-2、CB5-6外。 （Fig. 4） CB5、CB6取付場合、必CB5側Blue/Black色、CB6側Red/Black色取付。d. AUDIO P.C.B.前方持上、取外。（Fig. 4）Fig. 44. Removal of Front Frame assya. Remove 4 screws (8), 2 screws (9) (B, G mod

46、els) andthen remove the frame top. (Fig. 4)b. Remove 9 screws (0). (Fig. 4)c. Remove CB601 and CB902. (Fig. 4)d. Remove the front frame assy. (Fig. 4)5. Removal of AUDIO P.C.B.a. Remove 6 screws (A). (Fig. 4)b. Remove 4 screws (B) and 4 screws (C). (Fig. 5)c. Remove CB1-2 and CB5-6. (Fig. 4)*When in

47、stalling CB5 and CB6, be sure to con-nect the Blue/Black color cable to CB5 and theRed/Black cable to the CB6.d. Lift the front of AUDIO P.C.B. and then remove it. (Fig. 4)Frame topAUDIO P.C.B.(B, G, J models)Loader assyASSYFront frame assy ASSYSupport AUDIOAUDIODA8HFGEE89A0000DCB301CB302CB612CB903C

48、B601CB902CB1CB2CB5CB6Frame mecha LLFrame mecha RRPush rivetPush rivetSupport FFSupport FFCD-S200013AUDIO P.C.B.場合： 本機上布敷、上P.C.B.裏返置。 （Fig. 6） 外 （） 接続。次区間、用延長使用。AUDIO P.C.B.：CB2DIGITAL P.C.B.：CB30312P、450 mm P=1.25 （MF112450） 接続際、極性注意。 本機P.C.B.接続。P.C.B.取外場合、線等接続。（Fig. 6）Fig. 5When checking the AUDIO

49、P.C.B.:Put the rubber sheet and cloth over this unit. Thenplace the P.C.B.s upside down on the cloth andcheck it. (Fig. 6)Reconnect all cables (connectors) that have beendisconnected.Be sure to use the extension cable before servicingthe following section.AUDIO P.C.B.: CB2_DIGITAL P.C.B.: CB30312P,

50、450mm P=1.25 (MF112450)When connecting the flexible flat cable, be carefulwith polarity.In this unit, the ground of P.C.B.s shown below isconnected to the rear panel and chassis. When theseP.C.B.s are removed from the rear panel, connect theground point to the rear panel or chassis, using aground le