Yamaha-CDS1000-cd-sm 维修电路原理图.pdf

《Yamaha-CDS1000-cd-sm 维修电路原理图.pdf》由会员分享，可在线阅读，更多相关《Yamaha-CDS1000-cd-sm 维修电路原理图.pdf（57页珍藏版）》请在收音机爱好者资料库上搜索。

1、I CONTENTSTO SERVICE PERSONNEL . 23PREVENTION OF ELECTROSTATIC DISCHARGE . 4FRONT PANEL . 5REAR PANELS . 57REMOTE CONTROL PANEL . 8SPECIFICATIONS / 参考仕様. 89INTERNAL VIEW . 9DISASSEMBLY PROCEDURES / 分解手順. 1016TEST MODE / . 17UPDATING FIRMWARE / 書込. 1824DISPLAY DATA . 25IC DATA . 2628PIN CONNECTION DI

2、AGRAMS. 2930BLOCK DIAGRAM. 31PRINTED CIRCUIT BOARDS. 3240SCHEMATIC DIAGRAMS. 4145REPLACEMENT PARTS LIST . 4756REMOTE CONTROL. 57101092SERVICE MANUALSUPER AUDIO CD PLAYERCopyright 2008 All rights reserved.This manual is copyrighted by YAMAHA and may not be copied orredistributed either in print or el

3、ectronically without permission.P.O.Box 1, Hamamatsu, Japan 08.05IMPORTANT NOTICEThis manual has been provided for the use of authorized YAMAHA Retailers and their service personnel.It has been assumed that basic service procedures inherent to the industry, and more specifically YAMAHA Products, are

4、 alreadyknown and understood by the users, and have therefore not been restated.WARNING:Failure to follow appropriate service and safety procedures when servicing this product may result in personalinjury, destruction of expensive components, and failure of the product to perform as specified. For t

5、hese reasons,we advise all YAMAHA product owners that any service required should be performed by an authorizedYAMAHA Retailer or the appointed service representative.IMPORTANT:The presentation or sale of this manual to any individual or firm does not constitute authorization, certification orrecogn

6、ition of any applicable technical capabilities, or establish a principle-agent relationship of any form.The data provided is believed to be accurate and applicable to the unit(s) indicated on the cover. The research, engineering, andservice departments of YAMAHA are continually striving to improve Y

7、AMAHA products. Modifications are, therefore, inevitableand specifications are subject to change without notice or obligation to retrofit. Should any discrepancy appear to exist, pleasecontact the distributors Service Division.WARNING:Static discharges can destroy expensive components. Discharge any

8、 static electricity your body may haveaccumulated by grounding yourself to the ground buss in the unit (heavy gauge black wires connect to this buss).IMPORTANT:Turn the unit OFF during disassembly and part replacement. Recheck all work before you apply power to the unit.CD-S1000CD-S1000RadioFans.CN

9、收音机爱 好者资料库2CD-S1000CD-S1000WALLOUTLETEQUIPMENTUNDER TESTAC LEAKAGETESTER OREQUIVALENTINSULATINGTABLEWARNING: CHEMICAL CONTENT NOTICE!This product contains chemicals known to the State of California to cause cancer, or birth defects or other reproductiveharm.DO NOT PLACE SOLDER, ELECTRICAL/ELECTRONIC

10、 OR PLASTIC COMPONENTS IN YOUR MOUTH FOR ANYREASON WHAT SO EVER!Avoid prolonged, unprotected contact between solder and your skin! When soldering, do not inhale solder fumes or exposeeyes to solder/flux vapor!If you come in contact with solder or components located inside the enclosure of this produ

11、ct, wash your hands beforehandling food.1. Critical Components InformationComponents having special characteristics are marked sand must be replaced with parts having specifications equalto those originally installed.2. Leakage Current Measurement (For 120V Models Only)When service has been complete

12、d, it is imperative to verifythat all exposed conductive surfaces are properly insulatedfrom supply circuits.GMeter impedance should be equivalent to 1500 ohms shuntedby 0.15F.GLeakage current must not exceed 0.5mA.GBe sure to test for leakage with the AC plug in both polarities.本機搭載基板付接合部無鉛付。無鉛種類、修

13、理時下記無鉛使用推奨。 Sn+Ag+Cu （錫+銀+銅） Sn+Cu （錫+銅） Sn+Zn+Bi （錫+亜鉛+）注意：無鉛融点温度通常鉛入比3040程度高、合使用。All of the P.C.B.s installed in this unit and solder joints aresoldered using the lead free solder.Among some types of lead free solder currently available,it is recommended to use one of the following types for there

14、pair work.Sn + Ag + Cu (tin + silver + copper)Sn + Cu (tin + copper)Sn + Zn + Bi (tin + zinc + bismuth)Caution:As the melting point temperature of the lead free solder isabout 30C to 40C (50F to 70F) higher than that of the leadsolder, be sure to use a soldering iron suitable to each solder.About le

15、ad free solder / 無鉛I TO SERVICE PERSONNELWARNING: Laser SafetyThis product contains a laser beam component. This component may emit invisible, as well as visible radiation,which may cause eye damage. To protect your eyes and skin from laser radiation, the following precautions must beused during ser

16、vicing of the unit.1) When testing and/or repairing any component within the product, keep your eyes and skin more than 30 cm away fromthe laser pick-up unit at all times. Do not stare at the laser beam at any time.2) Do not attempt to readjust, disassemble or repair the laser pick-up, unless noted

17、elsewhere in this manual.3) CAUTION : Use of controls, adjustments or performance of procedures other than those specified herein may result inhazardous radiation exposure.Laser Emitting conditions:1) When the top cover is removed, and the STANDBY/ON SW is turned to the “ON” position, the laser comp

18、onent will emita beam for several seconds to detect if a disc is present. During this time (5-10 sec.) the laser may radiate through thelens of the laser pick-up unit. Do not attempt any servicing during this period!If no disc is detected, the laser will stop emitting the beam. When a disc is loaded

19、, you will not be exposed to any laseremissions.2) The laser power level can be adjusted with the VR on the pick-up PWB, however, this level has been set by the factoryprior to shipping from the factory. Do not adjust this laser level control unless instruction is provided elsewhere in thismanual. A

20、djustment of this control can increase the laser emission level from the device.RadioFans.CN 收音机爱 好者资料库3CD-S1000CD-S1000CAUTION - VISIBLE AND / OR INVISIBLE LASER RADIATION WHEN OPEN. AVOID EXPOSURE TO BEAM.VARNING - SYNLIG OCH / ELLER OSYNLIG LASERSTRLNING NR DENNA DEL R PPNAD. STRLEN R FARLIG.VARO

21、 ! AVATTAESSA OLET ALTTIINA NKYVLLE JA / TAI NKYMTMLLE LASERSTEILYLLE. L KATSO STEESEEN.VARNING - SYNLIG OCH / ELLER OSYNLIG LASERSTRLNING NR DENNA DEL R PPNAD. BETRAKTA EJ STRLEN.VORSICHT ! SICHTBARE UND / ODER UNSICHTBARE LASERSTRAHLUNG WENN ABDECKUNG GEFFNET. NICHT DEM STRAHL AUSSETZEN.ATTENTION

22、- PADIATION VISIBLE ET / OU INVISIBLE LORSQUE LAPPAREIL EST OUVERT. EVITEZ TOUTE EXPOSITION AU FAISCEAU.CAUTION-CLASS 1M LASER RADIATION WHEN OPENDO NOT VIEW DIRECTLY WITH OPTICAL INSTRUMENTS.Material:SA-CDSemiconductor laser (AlGaInP)CDSemiconductor laser (AlGaAs)Wavelength:SA-CD650 nmCD780 nmWarni

23、ng for power supplyThe primary side of the power supply carries live mains voltage when the player is connected to the mains even whenthe player is switched off !This primary area is not shielded so it is possible to accidentally touch copper tracks and/or components when servicing theplayer.Service

24、 personnel have to take precautions to prevent touching this area or components in this area.Note:The screws on the DVD mechanism may never be touched, removed or re-adjusted.Handle the DVD mechanism with care when the unit has to be exchanged!The DVD mechanism is very sensitive for dropping or givi

25、ng shocks.Laser Diode PropertiesLaser Output:SA-CD5 mW (max.)CD7 mW (max.)B, G models4CD-S1000CD-S1000I PREVENTION OF ELECTROSTATIC DISCHARGESome semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are calledElectrostatically Sensitive (ES) Devic

26、es. Examples of typical ES devices are integrated circuits and some field-effect transis-tors and semiconductor “chip” components. The following techniques should be used to help reduce the incidence of compo-nent damage caused by electro static discharge (ESD).1. Immediately before handling any sem

27、iconductor component or semiconductor-equipped assembly, drain off any ESD onyour body by touching a known earth ground. Alternatively, obtain and wear a commercially available discharging ESD wriststrap, which should be removed for potential shock reasons prior to applying power to the unit under t

28、est.2. After removing an electrical assembly equipped with ES devices, place the assembly on a conductive surface such asaluminum foil, to prevent electrostatic charge buildup or exposure of the assembly.3. Use only a grounded-tip soldering iron to solder or unsolder ES devices.4. Use only an anti-s

29、tatic solder removal device. Some solder removal devices not classified as “anti-static (ESD protected)”can generate electrical charge sufficient to damage ES devices.5. Do not use freon-propelled chemicals. These can generate electrical charges sufficient to damage ES devices.6. Do not remove a rep

30、lacement ES device from its protective package until immediately before you are ready to install it. (Mostreplacement ES devices are packaged with leads electrically shorted together by conductive foam, aluminum foil or compa-rable conductive material).7. Immediately before removing the protective m

31、aterial from the leads of a replacement ES divice, touch the protective mate-rial to the chassis or circuit assembly into which the device will be installed.CAUTION: Be sure no power is applied to the chassis or circuit, and observe all other safety precautions.8. Minimize bodily motions when handli

32、ng unpackaged replacement ES devices. (Otherwise harmless motion such as brush-ing together of your fabric clothes or lifting of your foot from a carpeted floor can generate static electricity (ESD) sufficientto damage an ES device).Grounding for electrostatic breakdown prevention1. Human body groun

33、ding.Use the antistatic wrist strap to discharge the static electricity from your body.2. Work table grounding.Put a conductive material (sheet) or steel sheet on the area where the optical pickup is placed and ground the sheet.Caution:The static electricity of your clothes will not be grounded thro

34、ugh the wrist strap. So take care not to let your clothes touch theoptical pickup.1M-ohmsConductive material(sheet) or steel sheetAnti-static wrist strap5CD-S1000CD-S1000I FRONT PANELCD-S1000 (U, C, R, T, K, A, B, G, L, J models)I REAR PANELSCD-S1000 (U, C models)CD-S1000 (R model)6CD-S1000CD-S1000C

35、D-S1000 (T model)CD-S1000 (K model)CD-S1000 (A model)7CD-S1000CD-S1000CD-S1000 (B, G models)CD-S1000 (L model)CD-S1000 (J model)8CD-S1000CD-S1000I Audio Section / 部Frequency Response / 周波数特性SA-CD . 2 Hz to 50 kHz (-3 dB)CD .2 Hz to 20 kHzTotal Harmonic Distortion (1 kHz) / 高調波歪率 （1 kHz）.0.002 % or l

36、essSignal to Noise Ratio / 信号対雑音比 (IHF-A Network).113 dB or moreDynamic Range / SA-CD .105 dB or moreCD .100 dB or moreOutput Level (1 kHz, 0 dB) / 出力 （1 kHz、0 dB）. 2.0 0.3 VI General / 総合Power Supply / 電源電圧U, C models .AC 120 V, 60 HzR, L models .AC 110/120/220/230-240 V, 50/60 HzT model.AC 220 V,

37、50 HzK model.AC 220 V, 60 HzA model.AC 240 V, 50 HzB, G models .AC 230 V, 50 HzJ model . AC 100 V, 50/60 HzPower Consumption / 消費電力U, C, R, T, K, A, B, G, L models . 30 WJ model . 25 WOff-state Power Consumption / OFF時消費電力. 0 WDimensions (W x H x D) / 寸法 （幅高奥行）. 435 x 137 x 440 mm (17-1/8” x 5-3/8”

38、x 17-5/16”)Weight / 質量. 15 kg (33 lbs. 1 oz.)Finish / 仕上Black color . U, C, R, T, K, A, B, G, L, J modelsSilver color . U, C, R, T, K, A, B, G, L, J modelsAccessories / 付属品Remote control x 1, Battery (R6, AA, UM-3) x 2, Audio pin cable (1.5 m)x 1, Power cable (2 m) x 1*Specifications are subject to

39、change without notice due to productimprovements. 参考仕様外観予告変更。I SPECIFICATIONS / 参考仕様U . U.S.A. modelC . Canadian modelR . General modelT . Chinese modelK . Korean modelA . Australian modelB . British modelG . European modelL . Singapore modelJ. Japanese modelI REMOTE CONTROL PANELCDX59CD-S1000CD-S10

40、00DIMENSIONS / 寸法図Unit: mm (inch)単位：mm （）I INTERNAL VIEW435 (17-1/8)371 (14-5/8)137 (5-3/8)440 (17-5/16)418 (16-7/16)362 (14-1/4)120 (4-3/4)8(5/16)14(9/16)17(11/16)1 POWER TRANSFORMER2 POWER (2) P.C.B. (R, L models)3 POWER (1) P.C.B.4 LOADER UNIT5 AUDIO P.C.B.6 DIGITAL (1) P.C.B.7 DIGITAL (5) P.C.B.

41、8 POWER (3) P.C.B.9 DIGITAL (4) P.C.B.0 DIGITAL (3) P.C.B.A DIGITAL (2) P.C.B.234567A890110CD-S1000CD-S1000I DISASSEMBLY PROCEDURES / 分解手順Fig. 1(Remove parts in the order as numbered.)Disconnect the power cable from the AC outlet.1. Removal of Panel Side L/Ra. Remove 2 screws (1), coned disc spring

42、L and washerside. (Fig. 1)b. Lift the panel side L a little, release hooks at 3 locationsand then remove the panel side L. (Fig. 1)c. Remove 2 screws (2) and then remove 2 washers.(Fig. 1)d. Lift the panel side R a little, release hooks at 3 loca-tions and remove the panel side R. (Fig. 1)2. Removal

43、 of Top Covera. Remove 7 (U, C models) / 5 (R, T, K, A, B, G, L models)screws (3), 2 screws (4) and 2 screws (5). (Fig. 1)b. Remove the top cover. (Fig. 1)（番号順部品取外。）AC電源、電源抜。1. L/R外方a. 12本、L、外。 （Fig. 1）b. L少持上、3所外、L取外。 （Fig. 1）c. 22本外、2個外。 （Fig. 1）d. R少持上、3所外、R取外。 （Fig. 1）2. 外方a. 35本、42本、52本外。（Fig.

44、1）b. 取外。 （Fig. 1）Panel side L LPanel side R RWasher sideWasher sideConed disc spring LLConed disc spring LLFront panelTop cover76731333452HookU, C modelsHookPOWER ON / OFF switch“POWER ON / OFF” HookLid11CD-S1000CD-S1000Fig. 23. 外方a. 底面下図矢印方向動。 （Fig. 2） 、押出。b. 後方押、押出。 （Fig. 3）c. 62本外、取外。 （Fig. 1）d.

45、前方押、閉。e. 78本外。 （Fig. 1）f. “POWER ON/OFF” ON。g. “POWER ON/OFF” 傷前方取外。 （Fig. 1）Fig. 33. Removal of Front Panela. Using a flatblade screwdriver, move the slider at the bot-tom in the direction of the arrow shown below. (Fig. 2)*Tray lock will be released but will not come out.b. Push out the tray by pu

46、shing its rear. (Fig. 3)c. Using a phillips screwdriver, remove 2 screws (6) andthen remove the lid. (Fig. 1)d. Close the tray by pushing its front.e. Remove 8 screws (7). (Fig. 1)f.Set the “POWER ON/OFF” switch to the ON position.g. Remove the front panel forward gradually, using carenot to cause a

47、ny damage to the “POWER ON/OFF”switch. (Fig. 1)Flatblade screwdriver Tray12CD-S1000CD-S10004. ASSY外方a. 84本、92本外、取外。 （Fig. 4）b. 09本外。 （Fig. 4）c. CB601、CB902外。 （Fig. 4）d. ASSY取外。 （Fig. 4）5. AUDIO P.C.B.外方a. A6本外。 （Fig. 4）b. B4本外。 （Fig. 5）c. CB1-2、CB5-6外。 （Fig. 4） CB5、CB6同形状、取付場合必、CB5側Blue/Black色、CB6側R

48、ed/Black色取付。d. AUDIO P.C.B.前方持上、取外。（Fig. 4）Fig. 44. Removal of Front Frame assya. Remove 4 screws (8), 2 screws (9) (B, G models) andthen remove the frame top. (Fig. 4)b. Remove 9 screws (0). (Fig. 4)c. Remove CB601 and CB902. (Fig. 4)d. Remove the front frame assy. (Fig. 4)5. Removal of AUDIO P.C.B

49、.a. Remove 6 screws (A). (Fig. 4)b. Remove 4 screws (B). (Fig. 5)c. Remove CB1-2 and CB5-6. (Fig. 4)*When installing CB5 and CB6, be sure to con-nect the Blue/Black color cable to CB5 and theRed/Black cable to CB6. Both connectors havesame shape.d. Lift the front of AUDIO P.C.B. and then remove it.

50、(Fig. 4)Frame topAUDIO P.C.B.(B, G, J models)Loader unitFront frame assy ASSYSupport AUDIOAUDIOCA8GEFDD89A0000CCB301CB302CB612CB903CB601CB902CB1CB2CB5CB6Frame mecha LLFrame mecha RRPush rivetPush rivetSupport FFSupport F FCD-S100013AUDIO P.C.B.場合： 本機上布敷、上P.C.B.裏返置。 （Fig. 6） 外 （） 接続。次区間、用延長使用。AUDIO P