Sony-DZ500F-sacd-sm 维修电路原理图.pdf

《Sony-DZ500F-sacd-sm 维修电路原理图.pdf》由会员分享，可在线阅读，更多相关《Sony-DZ500F-sacd-sm 维修电路原理图.pdf（79页珍藏版）》请在收音机爱好者资料库上搜索。

1、SERVICE MANUALSony CorporationHome Audio DivisionPublished by Sony Techno Create CorporationAEP ModelUK ModelSUPER AUDIO CD/DVD RECEIVER9-879-629-032006C16-1 2006.03Ver. 1.2 2006.03HCD-DZ500FHCD-DZ500F is the amplifier, DVD/CD andtuner section in DAV-DZ500F.SPECIFICATIONSModel Name Using Similar Mec

2、hanismHCD-DZ300Mechanism TypeCDM85-DVBU102Optical Pick-up NameKHM-310CAA/C2NPThis system incorporates with Dolby*1 Digital and DolbyPro Logic (II) adaptive matrix surround decoder and theDTS*2 Digital Surround System.*1 Manufactured under license from Dolby Laboratories.“Dolby,” “Pro Logic,” and the

3、 double-D symbol aretrademarks of Dolby Laboratories.*2 Manufactured under license from Digital TheaterSystems, Inc.“DTS” and “DTS Digital Surround” are trademarks ofDigital Theater Systems, Inc.Amplifier sectionStereo mode (rated)55 W + 55 W (3 ohms at 1 kHz, DIN)Surround mode (reference)music powe

4、r outputFront: 143 W + 143 W(with SS-TS46)Center*: 143 W(with SS-CT46)Surround*: 143 W + 143 W(with SS-TS46B)Subwoofer*: 285 W(with SS-WS42)* Depending on the sound field settings and the source, there may be no sound output.InputsTV, SATSensitivity: 450 mVImpedance: 50 kilohmsAUDIO IN Sensitivity:

5、250/125 mVImpedance: 50 kilohmsPhonesAccepts low-and high-impedance headphones.Super Audio CD/DVD systemLaser Semiconductor laser(Super Audio CD/DVD: = 650 nm)(CD: = 790 nm)Emission duration: continuousSignal format systemPAL/NTSCFrequency response (at 2 CH STEREO mode)DVD (PCM): 2 Hz to 22 kHz (1.0

6、 dB)CD: 2 Hz to 20 kHz (1.0 dB)Harmonic distortionLess than 0.03 %Tuner sectionSystemPLL quartz-locked digital synthesizer systemFM tuner sectionTuning range87.5 108.0 MHz (50 kHz step)Antenna (aerial)FM wire antenna (aerial)Antenna (aerial) terminals 75 ohms, unbalancedIntermediate frequency10.7 MH

7、zAM tuner sectionTuning range531 1,602 kHz (with the interval set at 9 kHz)Antenna (aerial)AM loop antenna (aerial)Intermediate frequency450 kHzVideo sectionOutputsVideo: 1 Vp-p 75 ohmsR/G/B: 0.7 Vp-p 75 ohmsCOMPONENT:Y: 1 Vp-p 75 ohmsPB/CB, PR/CR: 0.7 Vp-p 75 ohmsInputVIDEO: 1 Vp-p 75 ohmsGeneralPo

8、wer requirements220 240 V AC, 50/60 HzPower consumptionOn: 160 WStandby: 0.3 W (at the Power Saving mode) Dimensions (approx.)430 70 295 mm (w/h/d) incl. projecting partsMass (approx.)3.6 kgDesign and specifications are subject to change without notice.RadioFans.CN 收音机爱 好者资料库2HCD-DZ500FMODEL IDENTIF

9、ICATION Rear Panel ModelPart No.EXCEPT RU model2-588-156-0RU model2-588-156-1 AbbreviationRU: Russian model.CAUTIONUse of controls or adjustments or performance of proceduresother than those specified herein may result in hazardous radiationexposure.UNLEADED SOLDERBoards requiring use of unleaded so

10、lder are printed with the lead-free mark (LF) indicating the solder contains no lead.(Caution: Some printed circuit boards may not come printed withthe lead free mark due to their particular size): LEAD FREE MARKUnleaded solder has the following characteristics.Unleaded solder melts at a temperature

11、 about 40 C higherthan ordinary solder.Ordinary soldering irons can be used but the iron tip has to beapplied to the solder joint for a slightly longer time.Soldering irons using a temperature regulator should be set toabout 350 C.Caution: The printed pattern (copper foil) may peel away ifthe heated

12、 tip is applied for too long, so be careful!Strong viscosityUnleaded solder is more viscou-s (sticky, less prone to flow)than ordinary solder so use caution not to let solder bridgesoccur such as on IC pins, etc.Usable with ordinary solderIt is best to use only unleaded solder but unleaded solder ma

13、yalso be added to ordinary solder.Notes on chip component replacementNever reuse a disconnected chip component.Notice that the minus side of a tantalum capacitor may bedamaged by heat.Flexible Circuit Board RepairingKeep the temperature of the soldering iron around 270 Cduring repairing.Do not touch

14、 the soldering iron on the same conductor of thecircuit board (within 3 times).Be careful not to apply force on the conductor when solderingor unsoldering.SAFETY-RELATED COMPONENT WARNING!COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINEWITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND INTHE PARTS LIST ARE CRI

15、TICAL TO SAFE OPERATION.REPLACE THESE COMPONENTS WITH SONY PARTS WHOSEPART NUMBERS APPEAR AS SHOWN IN THIS MANUAL ORIN SUPPLEMENTS PUBLISHED BY SONY.Laser component in this product is capable of emitting radiationexceeding the limit for Class 1.This appliance is classified asa CLASS 1 LASER product.

16、The CLASS 1 LASERPRODUCT MARKING islocated on the rear exterior.SPEAKERCOAXIALFM75YR AUDIO INVIDEO INLPB/CBPR/CRDVD ONLYSATCOMPONENT VIDEO OUTEURO AVOUTPUT(TO TV)AMFRONT RFRONT LSURR RSURR LCENTERWOOFERParts No.RadioFans.CN 收音机爱 好者资料库3HCD-DZ500FTABLE OF CONTENTS1.SERVICING NOTE.42.GENERAL.63.DISASSE

17、MBLY3-1.Disassembly Flow .83-2.Case, Front Panel Assy .93-3.FL Board, H/P Board. 103-4.STBY Board, IPOD Board, KEY Board . 103-5.I/O Board, DC Fan . 113-6.DMB10 Board . 113-7.MAIN Board. 123-8.DVD Mechanism Deck (CDM85-DVBU102) . 133-9.Tray. 133-10. Belt, MS-203 Board . 143-11. Base Unit . 153-12. O

18、ptical Pick-up (KHM-310CAA/C2NP) . 154.TEST MODE. 165.DIAGRAMS5-1.Block Diagram RF/SERVO Section . 22 VIDEO Section . 23 AMP Section . 24 AUDIO Section . 25 POWER Section . 265-2.Printed Wiring Board DMB10 Section (Side A) . 275-3.Printed Wiring Board DMB10 Section (Side B) . 285-4.Schematic Diagram

19、 DMB10 Section (1/4) . 295-5.Schematic Diagram DMB10 Section (2/4) . 305-6.Schematic Diagram DMB10 Section (3/4) . 315-7.Schematic Diagram DMB10 Section (4/4) . 325-8.Printed Wiring Board MAIN Section (Side A) . 335-9.Printed Wiring Board MAIN Section (Side B) . 345-10. Schematic Diagram MAIN Sectio

20、n (1/7) . 355-11. Schematic Diagram MAIN Section (2/7) . 365-12. Schematic Diagram MAIN Section (3/7) . 375-13. Schematic Diagram MAIN Section (4/7) . 385-14. Schematic Diagram MAIN Section (5/7) . 395-15. Schematic Diagram MAIN Section (6/7) . 405-16. Schematic Diagram MAIN Section (7/7) . 415-17.

21、Printed Wiring Board PANEL Section (1/2) . 425-18. Schematic Diagram PANEL Section (1/2) . 435-19. Printed Wiring Board PANEL Section (2/2) . 445-20. Schematic Diagram PANEL Section (2/2) . 455-21. Printed Wiring Board I/O Section (Side A) . 465-22. Printed Wiring Board I/O Section (Side B) . 475-23

22、. Schematic Diagram I/O Section (1/2) . 485-24. Schematic Diagram I/O Section (2/2) . 496.EXPLODED VIEWS6-1.Overall Section . 616-2.Front Panel Assy Section. 626-3.Chassis Section. 636-4.DVD Mechanism Deck Section . 647.ELECTRICAL PARTS LIST. 654HCD-DZ500FSECTION 1SERVICING NOTENOTES ON HANDLING THE

23、 OPTICAL PICK-UP BLOCKOR BASE UNITThe laser diode in the optical pick-up block may suffer electrostaticbreak-down because of the potential difference generated by thecharged electrostatic load, etc. on clothing and the human body.During repair, pay attention to electrostatic break-down and alsouse t

24、he procedure in the printed matter which is included in therepair parts.The flexible board is easily damaged and should be handled withcare.NOTES ON LASER DIODE EMISSION CHECKThe laser beam on this model is concentrated so as to be focused onthe disc reflective surface by the objective lens in the o

25、ptical pick-up block. Therefore, when checking the laser diode emission,observe from more than 30 cm away from the objective lens.LASER DIODE AND FOCUS SEARCH OPERATIONCHECKCarry out the “S curve check” in “CD section adjustment” and checkthat the S curve waveform is output several times.DISC SLOT L

26、OCKThe disc slot lock function for the antitheft of an demonstrationdisc in the store is equipped.Setting Procedure :1.Press the ?/1 button to turn the set on.2.Press the FUNCTION button to set DVD function.3.Insert a disc.4.Press the x stick and the A button simultaneously for fiveseconds.5.The mes

27、sage “LOCKED” is displayed and the slot is locked.Releasing Procedure :1.Press the x stick and the A button simultaneously for fiveseconds again.2.The message “UNLOCKED” is displayed and the slot isunlocked.Note:When “LOCKED” is displayed, the slot lock is not released byturning power on/off with th

28、e ?/1 button.Note 1:Regarding the notification symbol “R”Because the number of the operating buttons of this product arelimited, some operations require use of the operating buttons ofthe remote commander, When a specific operation requires useof the operating buttons of the remote commander, “R” is

29、 addedto the specific operating procedure in this manual.Example MENU/NO “R” The MENU/NO button of remotecommander.Note 2:Incorrect operations may be performed if the test mode ia notentered properly.In this case, press the ?/1 button to turn the power off, andretry to enter the test mode.Note 3:If

30、the disc tray does not open and the message “LOCKED”appears, press the x stick and the A button simultaneouslyfor seconds or longer.Then remove your fingers from the above stick and the button.The message “UNLOCKED” appears for 2 seconds and the disctray opens.Note on DMB10 board replacementNew part

31、 of EEP ROM (IC103) on the DMB10 board cannot beused. Therefore, if the mounted DMB10 board (A-1108-644-A)is replaced, exchange new EEP ROM (IC103) with that usedbefore the replacement.When the self-diagnosis function is activated to prevent the system from malfunctioning, a 5-character service numb

32、er (e.g., C 13 50) with a combination of a letter and 4 digits appears on the screen and the front panel display. In this case, check the following table.Self-diagnosis Function (When letters/numbers appear in the display)First 3 characters of the service numberCause and/or corrective actionC 13The

33、disc is dirty.,Clean the disc with a soft cloth C 31The disc is not inserted correctly.,Restart the system, then re-insert the disc correctly.E XX(xx is a number)To prevent a malfunction, the system has performed the self-diagnosis function.,Contact your nearest Sony dealer or local authorized Sony

34、service facility and give the 5-character service number.Example: E 61 10C:13:505HCD-DZ500F SERVICE POSITION (DMB10 BOARD)When servicing side B of the DMB10 boardRemove the DMB10 board from bracket.(Refer to DISASSEMBLY 3-6. (page 11).Set the DMB10 board facing the side B upward as shown.Connect the

35、 cable and make the repair work.DMB10 board (side B)DMB bracket6HCD-DZ500FSECTION 2GENERALThis section is extractedfrom instruction manual.For more information, refer to the pages indicated in parentheses.Front panelA /1 (on/standby) (30, 34, 75)B Disc tray (34)C A (open/close) (34, 75)D H (play) (3

36、4)E X (pause) (34)F x (stop) (34, 75)G ./ (34)H FUNCTION (34)I PHONES jack (34)J VOLUME (34)K (remote sensor) (13)L Front panel display (94)M AUDIO IN jackIndex to Parts and ControlsRear panelA SPEAKER jacks (15)B COMPONENT VIDEO OUT jacks (24)C EURO AV T OUTPUT (TO TV) jacks (24)D AM terminal (23)E

37、 FM 75 COAXIAL jack (23)F SAT VIDEO/AUDIO IN jacks (26, 28)SPEAKERCOAXIALFM75YR AUDIO INVIDEO INLPB/CBPR/CRDVD ONLYSATCOMPONENT VIDEO OUTEURO AVOUTPUT(TO TV)AMFRONT RFRONT LSURR RSURR LCENTERWOOFER7HCD-DZ500FRemoteA TV /1 (on/standby) (69)B TV/VIDEO (69)C TUNER MENU (72)D SLEEP (74)E SA-CD/CD (39)F

38、PROGRESSIVE (25)G REPEAT/FM MODE (37, 73)H MULTI/2CH (39)I Number buttons (38, 65, 69)The number 5 button has a tactile dot.*J CLEAR, - (31, 36, 69, 70)K TOP MENU (38)L C/X/x/c/ENTER (30, 36, 60, 65, 71, 75, 76)M O RETURN (40)N REPLAY, STEP (34)O . PRESET , TV CH (31, 34, 69, 73)P m/ SLOW, TUNING (5

39、0, 72)Q H (play) (34)The H button has a tactile dot.*R TV (69)S THEATRE SYNC (70)T /1 (on/standby) (30, 34, 73)U AMP MENU (30, 71, 75)V DSGX (63)W FUNCTION (25, 34, 62, 71)X SOUND FIELD (60)Y DISPLAY (73)Z PICTURE NAVI (44)wj AUDIO (58)wk SUBTITLE (64)wl ANGLE (64)e; ALBUM /+ (34, 70)ea MENU (38)es

40、MUTING (34)ed VOLUME, TV VOL +/ (34, 69, 73)The VOLUME, TV VOL + button has a tactile dot.*ef DISPLAY (10, 31, 36, 65, 76)eg PRESET +, TV CH + (31, 34, 69, 73)eh ADVANCE, STEP (34)ej M/ SLOW, TUNING + (50, 72)ek x (stop) (34, 65, 73)el X (pause) (34)* Use the tactile dot as a reference when operatin

41、g the system.8HCD-DZ500FSECTION 3DISASSEMBLY3-1.DISASSEMBLY FLOWThis set can be disassembled in the order shown below.The dotted square with arrow () prompts you to move to the next job when all of the works within the dotted square () arecompleted.3-3.FL BOARD, H/P BOARD(Page 10)3-4.STBY BOARD, IPO

42、D BOARD, KEY BOARD(Page 10)3-8.DVD MECHANISM DECK(CDM85-DVBU102)(Page 13)3-9.TRAY(Page 13)3-10.BELT, MS-203 BOARD(Page 14)3-11.BASE UNIT (DVBU102)(Page 15)3-12.OPTICAL PICK-UP (KHM-310CAA/C2NP)(Page 15)3-5.I/O BOARD, DC FAN(Page 11)3-7.MAIN BOARD(Page 12)3-6.DMB10 BOARD(Page 11)3-2.CASE, FRONT PANEL

43、 ASSY(Page 9)SET9HCD-DZ500F3-2.CASE, FRONT PANEL ASSYNote: Follow the disassembly procedure in the numerical order given.DVD lid 1 The lever is moved in the direction of the arrow with the thin rod. 2 3DVD lid assy4screw (CASE3 TP2)5screw (CASE3 TP2)6five screws (+BV 3) 7caseqffront panel assy8three

44、 screws (+BV 3)qswire (flat type) 19p(CN509) qdconnector (CNP309) qaconnector (CNP602) 0claw9claw10HCD-DZ500F3-4.STBY BOARD, IPOD BOARD, KEY BOARD3-3.FL BOARD, H/P BOARD2H/P board7shield (front)0FL board3knob (vol)4nut1tapping screw (DIA.2.6 8)8tapping screw (DIA.2.6 8)6three tapping screws (DIA.2.6

45、 8)5sheet 9wire (flat type) 19p(CN801)earth line9froating screw (PTPWHM 2.6)7STBY board0IPOD board2four tapping screws (DIA.2.6 8)6two tapping screws (DIA.2.6 8)5two tapping screws (DIA.2.6 8)1four tapping screws (DIA.2.6 8)4button (play)8button (power)3KEY board11HCD-DZ500F3-5.I/O BOARD, DC FAN3-6.

46、DMB10 BOARD2connector (CN300)1connector (CN901)7DC fanqdtunerqaI/O boardback panel3wire (flat type) 13p(CN4802)0wire (flat type) 11p(CN101)5wire (flat type) 23p(CN601)9two screws (+BV 3) 8two screws (+BV 3)4three screws (+BV 3)qstwo screws (+BV 3)6two screws (BVTT 4 8)qaDMB10 board3connector (CN201)

47、8connector (CN401)4wire (flat type) 24p(CN101)5wire (flat type) 13p(CN4802)7wire (flat type) 11p(CN4501)6wire (flat type) 7p(CN302)1wire (flat type) 13p(CN106)2wire (flat type) 7p(CN202)9two screws (+BV 3)0two screws (+BV 3)12HCD-DZ500F3-7.MAIN BOARD0MAIN board3heat sink (AMP)4wire (flat type) 11p(C

48、N505)5wire (flat type) 7p(CN503)6wire (flat type) 23p(CN507)7wire (flat type) 11p(CN504)8four screws (+BV 3) 1two screws (+BV 3)9five screws (+BV 3)2screw (BVTP 3 12)13HCD-DZ500F3-9.TRAY3-8.DVD MECHANISM DECK (CDM85-DVBU102)2dmb bracket1three screws (+BV 3)6DVD mechanism deck (CDM85-DVBU102)3three s

49、crews (+BV 3)4wire (flat type) 13p5connector423two claws5tray1Move the chuck cam in the direction of the arrow.bottom side14HCD-DZ500F3-10. BELT, MS-203 BOARD1two claws5three claws7 MS-203 board6 DC motor3 belt2 chuck cam4 screw(M 1.7 2.5) 15HCD-DZ500F3-12. OPTICAL PICK-UP (KHM-310CAA/C2NP)1two claw

50、sbu holder2loading base5two insulators6two insulators3four insulator screws4CDM85-DVBU1027optical pick-up (KHM-310CAA/C2NP) 3-11. BASE UNIT1two claws3two claws2 chuck cam4 base unit (DVBU102) 16HCD-DZ500FSECTION 4TEST MODENote 1:Regarding the notification symbol “R”Because the number of the operatin