Kenwood-DV303-cd-sm 维修电路原理图.pdf

《Kenwood-DV303-cd-sm 维修电路原理图.pdf》由会员分享，可在线阅读，更多相关《Kenwood-DV303-cd-sm 维修电路原理图.pdf（80页珍藏版）》请在收音机爱好者资料库上搜索。

1、DVD VCD CD PLAYERDV-303/DVF-5020/K5020SERVICE MANUALREVISED 1999-10/B51-5583-00 (K/K) 183670%In compliance with Federal Regulations, following are repro-ductions of labels on, or inside the product relating to laserproduct safety.KENWOOD-Crop. certifies this equipment conforms to DHHSRegulations No.

2、 21 DFR 1040. 10, Chapter 1, Subchapter J.DANGER : Laser radiation when open and interlockdefeated.AVOID DIRECT EXPOSURE TO BEAMCaution : No connection of ground line if disassemblethe unit. Please connect the ground line onrear panel, PCBs, Chassis and some others.NOTE : Please use the remote contr

3、ollerfor self-diagnosis and tilt adjust-ment.STANDBYVIRTUALSURROUNDOPEN/CLOSEDIGITAL OUTPUT(PCM/BIT STREAM)OPTICALCOAXIALAUDIO OUTPUTVIDEO OUTPUTVIDEO OUTPUTSELECTIONCOMPONENTVIDEO OUTPUTCrCbYS-VIDEOAC INLRFront panel(A60-1788-08)Tray top(A29-1088-08)Top cover(A01-3749-08)Leg(J02-1468-08)Pin jack(E6

4、3-1135-08)Oscillating module(W02-2736-08)Y/C connector(E40-8534-08)RCA jack(E63-1134-08)Front cover(B10-3573-08)Power button(K27-2389-08)Switch(S90-0134-08)Connector(E40-8535-08)Pin jack(E63-1133-08)Figure is DV-303.Please use this manual instead of DV-303s manual (B51-5561-00), when repair of DV-30

5、3.DV-303/DVF-5020(k) COVER1,1P( 99.11.2 10:39 AM yW 1RadioFans.CN 收音机爱 好者资料库DV-303/DVF-5020/K50202CONTENTS / ACCESSORIESCONTENTS / ACCESSORIES . 2DISASSEMBLY FOR REPAIR.3BLOCK DIAGRAM .13CIRCUIT DESCRIPTION.17ADJUSTMENT.21ABBREVIATION.22VOLTAGE CHART.24WIRING DIAGRAM.30PC BOARD . 32SCHEMATIC DIAGRAM

6、 . 41EXPLODED VIEW .93PARTS LIST.96SPECIFICATIONS .Back coverContents(A70-1353-08): K,K1,Y(A70-1369-08): M(E30-2937-08): K,K1(E30-2946-08): Y,M(E30-2938-08)(E30-2365-05)Remote control unit . . . . . . . . . 1for remote control unit size AABatteries. . . . . . . . . . . . . . . . . . . . 2AC cord. .

7、. . . . . . . . . . . . . . . . . . . 1Video/audio cable. . . . . . . . . . . . 1Digital cord. . . . . . . . . . . . . . . . . . . 1(E03-0115-05): MAc plug adapter. . . . . . . . . . . . . . . 1Use to adapt the plug on the power cord tothe shape of the wall outlet.(Accessory only for regions where u

8、se isnecesary.)AccessoriesNote: There is different part in this manual as compared with a usual one because we use OEMfactorys data.Disassembly for repair is for DV-303.KENWOOD MODELOEM MODELDV-303,DVF-5020DVD-A120UDVF-K5020DVD-A160ENHow to read the schematic diagram There are some destinations in t

9、his schematic. Figures which is more than 20,000 is omitted first digit in Mic jack and Mic volume circuit. (Example) R4001 R24001Connection of from or to.Port nameDV-303/DVF-5020(k) COVER1,1P( 99.11.2 10:39 AM yW 2RadioFans.CN 收音机爱 好者资料库DV-303/DVF-5020/K50203DISASSEMBLY FOR REPAIR1-1 Casing Parts a

10、nd C.B.A. Positions1. Assembling and Disassembling the Casingand Checking C.B.A.s (DV-303)1-4 Disassembling the Front Panel1. Release the 3 tabs on the bottom.2. Release the 2 tabs on the left and right.3. Release the 2 tabs.4. Disconnect the 2 flexible cables.1-5 Disassembling the Loading Base Unit

11、1. Remove the 4 screws.2. Pull out the loading base unit vertically.NoteThere is a danger of damaging the connectors.1-2 Service PositionsNoteTo inspect the loading base unit, position the left sideupward (as viewed from the front).1-3 Disassembling the Tray1. Turn the lever clockwise.2. Move the tr

12、ay in the direction of the arrow until it locks.3. Release the tab locks on the left and right, then pull outthe tray.Extension cable (A)Extension cable (B)x2DV-303/DVF-5020(k) COVER1,1P( 99.11.2 10:39 AM yW 3DV-303/DVF-5020/K50204DISASSEMBLY FOR REPAIR1-6 Checking the Module C.B.A.1. Remove the 2 s

13、crews.2. Connect the module C.B.A. to the mother C.B.A. with theextension cables for inspection. Extension cable (B)x2Mother C.B.A. Module C.B.A.PP24201-PS4201PP23201-PS3201NoteBe sure to initialize the player whenever you replace aC.B.A. (Refer to page21/4-1 Initializing the DVD Player.)1-7 Disasse

14、mbling the Rear Panel,1. Remove all of the screws connected to the rear panel.(The number of screws varies according to the model).1-8 Checking the Power Supply C.B.A.1. Remove the 3 screws.2. Carefully pull out the power supply C.B.A.NoteThere is a danger of damaging the connectors.3. Connect the p

15、ower supply C.B.A. and the mother C.B.A.with the extension cable for inspection. Extension cable(A) (connects the power supply C.B.A.PS1101 and the mother C.B.A. PP21101)2. Release the two tabs on the left and right.Extension cable(A)DV-303/DVF-5020(k) COVER1,1P( 99.11.2 10:39 AM yW 4DV-303/DVF-5020

16、/K50205DISASSEMBLY FOR REPAIR1-9 Checking the Mother C.B.A.1. Remove the 5 screws.2. Release the 2 tabs.2. To preserve the quality of the optical pickup replacementparts during transport and installation, the terminals ofthe laser diode are short-circuited. After replacing theparts, use the proper p

17、rocedure to return the laser diodeto its original condition. (Refer to page9/2-12 Assemblingthe Optical Pickup.)3. Testers cannot be used to check the laser diode of theoptical pickup. The power supply inside the tester caneasily damage the laser diode.4. Take care when handling the flexible cable b

18、ecauseexcessive force can cause it to break.5. You cannot adjust the semifixed resistor for laser poweradjustment. Do not turn it.2-2 Disassembly ProcedureUse the following procedure to replace major parts. For the assembly procedure, follow the flow chart in reverse.3. Checked by connecting the mod

19、ule C.B.A. and the moth-er C.B.A. with the extension cables.Extension cable (B)x2Module C.B.A. Mother C.B.A.PS3201-PP23201PS4201-PP24201NoteBe sure to initialize the player whenever you replace aC.B.A. (Refer to page21/4-1, Initializing the DVD player.)2. Assembling and Disassembling the OpticalPick

20、up (Mechanical Parts)The optical pickup can be damaged by static electricity fromyour body. Be sure to take static electricity countermeasureswhen working around the optical pickup.2-1 Handling the Optical PickupThe optical pickup can be damaged by static electricityfrom your body. Be sure to take s

21、tatic electricity counter-measures when working around the optical pickup.1. The optical pickup is an extremely high-precision mecha-nism. Do not subject it to strong impact.Extension cable(B)Extensioncable(B)DV-303/DVF-5020(k) COVER1,1P( 99.11.2 10:40 AM yW 5DV-303/DVF-5020/K50206DISASSEMBLY FOR RE

22、PAIR2-3Lubricating the Loading Base UnitWhen replacing parts, lubricate the parts maked “xxx” in the diagramPart numberService ToolGrease410-0013-05Grease EM-30LGDV-303/DVF-5020(k) COVER1,1P( 99.11.2 10:40 AM yW 6DV-303/DVF-5020/K50207DISASSEMBLY FOR REPAIR2-4 Static Electricity CountermeasuresThe l

23、aser diode inside the traverse unit (optical pickup) canbe damaged by static electricity from your body. Be sure totake static electricity countermeasures when working aroundthe optical pickup.2-4-1 Static Electricity Countermeasure Methods1. Ground yourself Use an anti-static wrist strap to dischar

24、ge static electrici-ty from your body.2. Ground the workbenchLay a conductive material (sheet) or steel sheet on thesurface where the traverse unit (optical pickup) is to beplaced, then ground the sheet.2-5 Disassembling the Clamp Base UnitRemove the 2 screws.2-6 Disassembling the Clamper Weight, Cl

25、amperYoke, Magnet and Clamper1. Release the tab, and pull out the clamper.2. Release the 3 tabs on the clamper.2-4-2 Short-circuit the laser diodeSolder the land in the flexible cable of the optical pickup.Notes Be sure to do this befer disconnecting the flexible cableof the optical pickup from the

26、module C.B.A. Use an anti-static soldering iron to short-circuit andunshort-circuit laser diode.(Recommended soldering iron: Hakko with ESD counter-measure) After you have finished repairing the laser diode, followthe correct procedure to remove the solder from theshort-circuit location. (Refer to p

27、age5/2. Assembling andDisassembling the Optical Pickup (Mechanical Parts).)DV-303/DVF-5020(k) COVER1,1P( 99.11.2 10:40 AM yW 7DV-303/DVF-5020/K50208DISASSEMBLY FOR REPAIR2-7 Disassembling the Traverse Unit1. Remove the 3 screws.NoteBe sure to take static electricitiy countermeasures beferdisconnecti

28、ng the flexible cable.(Refer to page7/2-4 Stat-ic Electricity Countermeasures.)2. Disconnect the 2 flexible cables.2-8 Disassembling the Stepping Motor Unit1. Disconnect the flexible cable.2. Remove the 2 screws.NoteTake care when handling the flexible cable because itcan be broken by excessive forc

29、e.2-9 Disassembling the Optical Pickup Unit1. Remove the hook of the FPC holder, then remove theFPC holder itself.2. Remove the screw.3. Release the tab, then remove spring holder 1.NoteBe sure not to lose the spring.4. Remove the guide shaft.NoteBe sure to adjust the optical pickup tilt after repla

30、cing theoptical pickup.(Refer to page10/2-14 Opitcal Pickup Tilt Adjustment.)DV-303/DVF-5020(k) COVER1,1P( 99.11.2 10:40 AM yW 8DV-303/DVF-5020/K50209DISASSEMBLY FOR REPAIR2-10 Disassembling the Nut Unit1. Remove the screw.Notes The nut unit is not part of the optical pickup.Before replacing the opt

31、ical pickup, remove the nut unitfor use with the new optical pickup. After installation, use screw lock to lock the screw in posi-tion. When reassembling, use screw lock to lock the screw inposition after attaching it.2-12 Assembling the Optical Pickup1. Install the optical pickup.NoteTake care not

32、ot attach the tilt spring and guide shaft inthe wrong order.2. Fit the protruding part of the pickup FPC into the convex-part of the FPC holder to install it.2-11 Disassembling the Sub-Shaft Preload Spring1. Remove the screw.Notes Handle the sub-shaft preload spring carefully because theshape of the

33、 tip is easily deformed. The sub-shaft preload spring is not part of the opticalpickup. Before replacing the optical pickup, remove thesub-sahft preload spring for use with the new opticalpickup. After installation, use screw lock to lock the screw in posi-tion.DV-303/DVF-5020(k) COVER1,1P( 99.11.2

34、10:40 AM yW 9DV-303/DVF-5020/K502010DISASSEMBLY FOR REPAIR3. Insert the pickup FPC into connector FP5201 on the mod-ule C.B.A.2-14 Optical Pickup Tilt Adjustment4. Remove the solder from the pickup FPCs soldered short-circuit.5. Adjust the optical pickup tilt after removing the solder.(Refer to page

35、10/2-14 Optical Pickup Tilt Adjustment.)2-13 Disassembling the Spindle Motor Unit1. Remove the three screws.NoteBe sure to adjust the optical pickup tilt after replacing thespindle motor unit.DV-303/DVF-5020(k) COVER1,1P( 99.11.2 10:40 AM yW 10DV-303/DVF-5020/K502011DISASSEMBLY FOR REPAIRNotes Adjus

36、tment is generally unnecessary after replacing otherparts of the traverse unit. However, adjust if there is anoticeable degradation in picture quality. Optical adjustments cannot be made inside the opticalpickup. Adjustment is generally unnecessary after replacing thetraverse unit. Adjustment is gen

37、erally unnecessary after replacing thetraverse unit.DV-303/DVF-5020(k) COVER1,1P( 99.11.2 10:40 AM yW 11DV-303/DVF-5020/K502012DISASSEMBLY FOR REPAIR2-15 Disassembling the Intermediate Chassis1. Push the stopper downward, then rotate it until it contactsthe Vertical cam.2. Release the 2 tabs.2-17 Di

38、sassembling the Pulley Gear and Decelera-tion Gear1. Remove the screw.2. Remove the pulley gear.3. Remove the belt.4. Remove the deceleration gear.2-18 Disassembling the Mechanism LoadingC.B.A.1. Remove the 2 screws.2. Remove the 2 screws.3. Release the three tabs.2-16 Disassembling the Vertical cam

39、 and Drivegear1. Rotate the Vertical cam until it reaches the contact posi-tion.2. Lift the Vertical cam straight upward to pull it out.3. Remove the Drive gear.DV-303/DVF-5020(k) COVER1,1P( 99.11.2 10:40 AM yW 12DV-303/DVF-5020/K502013OVERALL BLOCK DIAGRAM27MHzRGB VIDEO/COMPONENT VIDEO OUT MODEL ON

40、LYONLYMODEL5.1chAUDIOAUDIO DIGITAL OUTIC3201 MOTHER C.B.A. PAL MODEL ONLYIC3061IC3051IC6001IC2511IC2501 MECHANISM UNIT MODULE C.B.A. CR(R)CB(B)Y(G)S-VIDEO OUTVIDEO OUTIC3531IC4221IC4211IC4201CNTSWSLSRFRFLCONVERTERD/AVIDEODRIVERVIDEOCONVERTERD/AAUDIOCONVERTERD/AAUDIOCONVERTERD/AAUDIOIC3001IC7001IC200

41、1IC5202(AV DEC)DECODERAVSRAM4BIT(ODC)CONTROLLERDISCOPTICALSRAM16BITCOILTRACKINGCOILFOCUSMOTORSTEPPINGCPUSUBKEYREMOCONLEDOSDFL(DSC)CONTROLLERSERVODIGITALIC6302IC6201CPUMAINDRAM4M16.9MHzDRIVEMOTOR4chMOTORLOADINGDRIVEMOTORSPINDLEMOTORSPINDLE(FEP)PROCESSORENDFRONTUNITPICK UPOPTICALDV-303/DVF-5020(k) COV

42、ER1,1P( 99.11.2 10:41 AM yW 13DV-303/DVF-5020/K502014(0.5sec./DIV.)CLOSE 2.5Vp-pIC2501-25(UP),IC2501-27(DOWN)5.0Vp-p(20usec./div.)IC2501-247.2Vp-p(20usec./div.)IC2511-11,12,13,14(0.5sec./DIV.)OPEN 2.5Vp-pIC2501-25(UP),IC2501-27(DOWN)RF SIGNALSPINDLE MOTOR DRIVE SIGNALSTEPPING MOTOR DRIVE SIGNALTRACK

43、ING ERROR SIGNALFOCUS ERROR SIGNALBRKFINRINSSFGCFGECECROPIN2-OPIN1-OPIN3-OPIN4-TRAY CLOSETRAY OPENBRKTRAY SET2TRAY SET1SSFGCFGECECRTRV-SWFOCUS DRIVETRAKING DRIVETRSDRV-BTRSDRV-AX TRONOFTRBDOJIT OUTLDONALDONBFBALFETBALTERDCKPRDCKNRDTPRDTNVIN4VIN3VIN2VIN1VIN5VIN6STNBYSTD1SCKSENDAT3DAT2DAT1DAT0SBI1SBO1

44、SBT1CPUIRQCPCENCPSENOUT2OUT1A3A2A1H1+H1-H2+H2-H3+H3-VO2-VO2+VO1-VO1+VO4+VO4-VO3+VO3-QCDOPTICAL PICK UP UNITPHOTO DETECTORB3B4B2B1A3A2A4A1LASER DIODEAMPHEADQ5201LD DRIVE43IC6303(EEPROM)AMP1151141131127176506052727055265IC6201(CPU)IC7001(ODC)INTERFACEBALANCEFOCUSBALANCETRACKING222120199796959492912321

45、92366656412132850494847(FEP)IC52026163626038373635343312810744819893209143424140178131216141111201211110310210510423269234567161110151219182527232628111213141516171863(DSC)IC2001QR25025413AMPQR2503QR2501AMP5413AMP(MOTOR DRIVE)(SPINDLE MOTOR DRIVE)IC2501IC2511M2601LOAD M-LOAD M+MOTORLOADINGS2601TRAY

46、OPENTRAY CLOSEM3M2M1H1-HALL1H1+H2-H2+HALL2H3+H3-TRV-SWHALL3TRAVERSE SWITCHACT T-ACT T+ACT F-ACT F+STEPPING MOTOR UNITSTEPPING MOTORLOADING MOTOR UNITSPINDLE MOTOR UNITOPTICAL PICK UP UNITACTUATORCOILTRACKINGCOILFOCUSSERVO BLOCK DIAGRAMDV-303/DVF-5020(k) COVER1,1P( 99.11.2 10:41 AM yW 14EXCEPT A112U,

47、A115UA115UA112U,EXCEPTVGOUT196Q3221Q3231AMPAMPSERIES MODEL ONLYEXCEPT A770,A360EXCEPT A770,A360 SERIES1.2Vp-p(20usec/div)IC3001-2011.5Vp-p(20usec/div)IC3001-2061.2Vp-p(20usec./div.)IC3201-232.2Vp-p(20usec./div.)IC3531-192.2Vp-p(20usec./div.)IC3531-161.5Vp-p(20usec./div.)IC3201-251.2Vp-p(20usec./div.

48、)IC3531-140.64Vp-p(20usec./div.)IC3201-320.68Vp-p(20usec./div.)IC3201-296.0Vp-p(20usec./div.)IC3001-161 to 168 MODULE C.B.A. MOTHER C.B.A. (AV DECORDER)IC3001A770,A360,SERIES MODEL ONLYXRST122IC6201-79PINFROMNRSTXRESET45VCOUTVYOUTCY201206Q3211AMPAMPQ3201FL3501B.P.F.L.P.F.FL3511Q3501AMPAMPQ3511Q3502A

49、MPAMPQ3512VR3511VR3501C ADJ.Y ADJ.A770,A360 SERIES MODEL ONLYQ3601AMPQ3602AMPQR3601NRIC6201-80PINFROMAMPQ3513AMPQ3603VIDEO OUT(VIDEO DRIVER)IC3531141619COUTVOUTCYOUT3 Y11VD7VD0168167166165164163162161(VIDEO D/A CONVERTER)IC3201IC6201-10PINFROMSDATAIC6201-9PINFROMSCLOCKP7P0SDATASCLOCK201998765432CB/B

50、 ADJVR3201CR/RCB/BY/GCYDAC-CDAC-BDAC-ADAC-FDAC-E382932352325ONLYEUROPE MODEL AMPQ3221AMPQ3231AMPQ3241FL3561FL3551B.P.F.AMPQ3571AMPQ3561Q3551AMP(VIDEO AMP)IC3581101315742OUTCOUTBOUTAINCINBINAMODELEXCEPT EUROPECR/RCB/BY/GJAPAN MODEL ONLYQR3521QR3522WIDE1IC6201-53PINFROMIC6201-5PINFROMWIDE2S-VIDEO OUTV