HarmanKardon-DVD27-cd-sm维修电路原理图.pdf
《HarmanKardon-DVD27-cd-sm维修电路原理图.pdf》由会员分享,可在线阅读,更多相关《HarmanKardon-DVD27-cd-sm维修电路原理图.pdf(110页珍藏版)》请在收音机爱好者资料库上搜索。
1、 harman kardon Model DVD 27DVD 27 DVD/CD/CD-R/CD-RW/VCD MP3 Player Service Manual - Contents - SERVICE PRECAUTIONS.2 BASIC SPECIFICATIONS.5 PACKAGE (120V).6 PACKAGE (230V).7 DETAILED SPECIFICATIONS.8 FRONT PANEL CONTROLS.11 INFORMATION DISPLAY.12 REMOTE CONTROL.13 REAR PANEL CONNECTIONS.16 CONNECTIO
2、NS/SETUP.17 TEST SCREEEN.19 PLAYBACK BASICS.20 BASIC TROUBLESHOOTING GUIDE.22 DISASSEMBLY PROCEDURE (120/230v).23 EXPLODED VIEW (120v).26 EXPLODED VIEW (230v).27 BLOCK DIAGRAM.28 ELECTRICAL PARTS LIST (120v) .29 SEMICONDUCTOR PINOUTS44 PCB DRAWINGS.96 SCHEMATICS.105 WIRING DIAGRAM.110 harman/kardon,
3、 Inc. 250 Crossways Park Dr. Woodbury, New York 11797 Rev0 3/2006 RadioFans.CN 收音机爱 好者资料库1SERVICING PRECAUTIONSNOTES REGARDING HANDLING OF THE PICK-UP1. Notes for transport and storage1) The pick-up should always be left in its conductive bag until immediately prior to use.2) The pick-up should neve
4、r be subjected to external pressure or impact.2. Repair notes1) The pick-up incorporates a strong magnet, and so should never be brought close to magnetic materials.2) The pick-up should always be handled correctly and carefully, taking care to avoid external pressure andimpact. If it is subjected t
5、o strong pressure or impact, the result may be an operational malfunctionand/or damage to the printed-circuit board.3) Each and every pick-up is already individually adjusted to a high degree of precision, and for that reasonthe adjustment point and installation screws should absolutely never be tou
6、ched.4) Laser beams may damage the eyes!Absolutely never permit laser beams to enter the eyes!Also NEVER switch ON the power to the laser output part (lens, etc.) of the pick-up if it is damaged.5) Cleaning the lens surfaceIf there is dust on the lens surface, the dust should be cleaned away by usin
7、g an air bush (such as usedfor camera lens). The lens is held by a delicate spring. When cleaning the lens surface, therefore, a cot-ton swab should be used, taking care not to distort this.6) Never attempt to disassemble the pick-up.Spring by excess pressure. If the lens is extremely dirty, apply i
8、sopropyl alcohol to the cotton swab. (Donot use any other liquid cleaners, because they will damage the lens.) Take care not to use too much ofthis alcohol on the swab, and do not allow the alcohol to get inside the pick-up.Storage in conductive bagNEVER look directly at the laser beam, and dont let
9、 contactfingers or other exposed skin.MagnetHow to hold the pick-upConductive SheetCotton swabPressurePressureDrop impactDVD27 DVD27 harman/kardon 2RadioFans.CN 收音机爱 好者资料库2NOTES REGARDING COMPACT DISC PLAYER REPAIRS1. Preparations1) Compact disc players incorporate a great many ICs as well as the pi
10、ck-up (laser diode). These compo-nents are sensitive to, and easily affected by, static electricity. If such static electricity is high voltage,components can be damaged, and for that reason components should be handled with care.2) The pick-up is composed of many optical components and other high-p
11、recision components. Care mustbe taken, therefore, to avoid repair or storage where the temperature of humidity is high, where strongmagnetism is present, or where there is excessive dust.2. Notes for repair1) Before replacing a component part, first disconnect the power supply lead wire from the un
12、it2) All equipment, measuring instruments and tools must be grounded.3) The workbench should be covered with a conductive sheet and grounded.When removing the laser pick-up from its conductive bag, do not place the pick-up on the bag. (This isbecause there is the possibility of damage by static elec
13、tricity.)4) To prevent AC leakage, the metal part of the soldering iron should be grounded.5) Workers should be grounded by an armband (1M)6) Care should be taken not to permit the laser pick-up to come in contact with clothing, in order to preventstatic electricity changes in the clothing to escape
14、 from the armband.7) The laser beam from the pick-up should NEVER be directly facing the eyes or bare skin.Resistor(1 Mohm)ConductiveSheetResistor(1 Mohm)ArmbandDVD27 DVD27 harman/kardon 33ESD PRECAUTIONSElectrostatically Sensitive Devices (ESD)Some semiconductor (solid state) devices can be damaged
15、 easily by static electricity. Such components com-monly are called Electrostatically Sensitive Devices (ESD). Examples of typical ESD devices are integrated cir-cuits and some field-effect transistors and semiconductor chip components. The following techniques shouldbe used to help reduce the incid
16、ence of component damage caused by static electricity.1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain offany electrostatic charge on your body by touching a known earth ground. Alternatively, obtain and wear acommercially available discharging wri
17、st strap device, which should be removed for potential shock reasonsprior to applying power to the unit under test.2. After removing an electrical assembly equipped with ESD devices, place the assembly on a conductive sur-face such as aluminum foil, to prevent electrostatic charge buildup or exposur
18、e of the assembly.3. Use only a grounded-tip soldering iron to solder or unsolder ESD devices.4. Use only an anti-static solder removal device. Some solder removal devices not classified as anti-staticcan generate electrical charges sufficient to damage ESD devices.5. Do not use freon-propelled chem
19、icals. These can generate electrical charges sufficient to damage ESDdevices.6. Do not remove a replacement ESD device from its protective package until immediately before you areready to install it. (Most replacement ESD devices are packaged with leads electrically shorted together byconductive foa
20、m, aluminum foil or comparable conductive materials).7. Immediately before removing the protective material from the leads of a replacement ESD device, touch theprotective material to the chassis or circuit assembly into which the device will by installed.CAUTION : BE SURE NO POWER IS APPLIED TO THE
21、 CHASSIS OR CIRCUIT, AND OBSERVE ALLOTHER SAFETY PRECAUTIONS.8. Minimize bodily motions when handing unpackaged replacement ESD devices. (Otherwise harmless motionsuch as the brushing together of your clothes fabric or the lifting of your foot from a carpeted floor can gen-erate static electricity s
22、ufficient to damage an ESD device).DVD27 DVD27 harman/kardon 4DVD 27 TECHNICAL SPECIFICATIONSApplicable Disc:Disc formats: 5-inch (12cm) or 3-inch (8cm) DVD-Video, Standard conforming DVD-R, DVD+R, DVD-RW, DVD+RW,VCD, CD, CD-R, CD-RW or MP3 discsRegion code: DVD Video disc with Code 1 or 0 onlyDVD-L
23、ayers: Single Side/Single Layer, Single Side/Dual Layer, Dual Side/Dual LayerAudio formats: Linear PCM, MPEG,Windows Media 8, Dolby Digital or DTS Audio DiscsStill image format: JPEGVideo Signal System:NTSCComposite Video Output:1V p-p/75 ohms, sync negative polarityS-Video Output:Y/Luminance: 1V p-
24、p/75 ohms, sync negative polarityC/Chrominance: 0.286V p-pComponent Video Output:Y: 1V p-p/75 ohms, sync negative polarityPr: 0.7V p-p/75 ohmsPb: 0.7V p-p/75 ohmsAnalog Audio Output:2V rms (1kHz, 0dB)Frequency Response:DVD (Linear PCM): 2Hz 22kHz +0/0.5dB (48kHz sampling)2Hz 44kHz +0/1.5dB (96kHz sa
25、mpling)CD:2Hz 20kHz +0/0.5dBSignal/Noise Ratio (SNR):105dB (A-weighted)Dynamic Range:DVD: 100dB (18-bit)/105dB (20-bit)CD/DVD: 96dB (16-bit)THD/1kHz:DVD/CD: 0.0025%Wow & Flutter:Below Measurable LimitsAC Power:110240VAC/5060HzPower Consumption:1 Watt (On/Standby)/11 Watts (Max)Dimensions (H x W x D)
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- HarmanKardon DVD27 cd sm 维修 电路 原理图